nils/gluon
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
v2021.1.x
gluon/patches/openwrt/0008-ipq40xx-add-support-for-Aruba-AP-303.patch

647 lines
17 KiB
Diff
Raw Permalink Normal View History

ipq40xx-generic: add support for Aruba AP-303
2019-12-20 21:49:46 +00:00
From: David Bauer <mail@david-bauer.net>
Date: Wed, 23 Oct 2019 22:25:14 +0200
Subject: ipq40xx: add support for Aruba AP-303
Hardware
--------
SoC: Qualcomm IPQ4029
RAM: 512M DDR3
FLASH: - 128MB NAND (Macronix MX30LF1G18AC)
- 4MB SPI-NOR (Macronix MX25R3235F)
TPM: Atmel AT97SC3203
BLE: Texas Instruments CC2540T
attached to ttyMSM0
ETH: Atheros AR8035
LED: WiFi (amber / green)
System (red / green)
BTN: Reset
To connect to the serial console, you can solder to the labled pads next
to the USB port or use your Aruba supplied UARt adapter.
Do NOT plug a standard USB cable into the Console labled USB-port!
Aruba/HPE simply put UART on the micro-USB pins. You can solder yourself
an adapter cable:
VCC - NC
D+ - TX
D- - RX
GND - GND
The console setting in bootloader and OS is 9600 8N1. Voltage level is
3.3V.
To enable a full list of commands in the U-Boot "help" command, execute
the literal "diag" command.
Installation
------------
1. Get the OpenWrt initramfs image. Rename it to ipq40xx.ari and put it
into the TFTP server root directory. Configure the TFTP server to
be reachable at 192.168.1.75/24. Connect the machine running the TFTP
server to the ethernet port of the access point.
2. Connect to the serial console. Interrupt autobooting by pressing
Enter when prompted.
3. Configure the bootargs and bootcmd for OpenWrt.
$ setenv bootargs_openwrt "setenv bootargs console=ttyMSM1,9600n8"
$ setenv nandboot_openwrt "run bootargs_openwrt; ubi part aos1;
ubi read 0x85000000 kernel; bootm 0x85000000"
$ setenv ramboot_openwrt "run bootargs_openwrt;
setenv ipaddr 192.168.1.105; setenv serverip 192.168.1.75;
netget; set fdt_high 0x87000000; bootm"
$ setenv bootcmd "run nandboot_openwrt"
$ saveenv
4. Load OpenWrt into RAM:
$ run ramboot_openwrt
5. After OpenWrt booted, transfer the OpenWrt sysupgrade image to the
/tmp folder on the device.
6. Flash OpenWrt:
$ ubidetach -p /dev/mtd1
$ ubiformat /dev/mtd1
$ sysupgrade -n /tmp/openwrt-sysupgrade.bin
To go back to the stock firmware, simply reset the bootcmd in the
bootloader to the original value:
$ setenv bootcmd "boot"
$ saveenv
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 102c8c55f217606cdbdc9a449667e034676b3e75)
diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network
index 01825b8bac46eec6325de00396d96307c946f975..49dd570242533068adf2c9df89e78560ba5f70eb 100755
--- a/target/linux/ipq40xx/base-files/etc/board.d/02_network
+++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network
@@ -39,6 +39,7 @@ ipq40xx_setup_interfaces()
ucidef_add_switch "switch0" \
"0u@eth0" "1:lan" "2:lan" "3:lan" "4:lan"
;;
+ aruba,ap-303|\
avm,fritzrepeater-1200|\
engenius,eap1300|\
meraki,mr33|\
diff --git a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index b0035ce8a394b6e87d7d89b9f55a6ec7c66e448e..15a2f2c09f8a92cc0accfbf9a977dbeb3355570d 100644
--- a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -137,6 +137,10 @@ case "$FIRMWARE" in
qcom,ap-dk01.1-c1)
ath10kcal_extract "ART" 4096 12064
;;
+ aruba,ap-303)
+ ath10kcal_extract "ART" 4096 12064
+ ath10kcal_patch_mac_crc $(mtd_get_mac_binary mfginfo 29)
+ ;;
asus,map-ac2200)
ath10kcal_ubi_extract "Factory" 4096 12064
;;
@@ -199,6 +203,10 @@ case "$FIRMWARE" in
qcom,ap-dk01.1-c1)
ath10kcal_extract "ART" 20480 12064
;;
+ aruba,ap-303)
+ ath10kcal_extract "ART" 20480 12064
+ ath10kcal_patch_mac_crc $(macaddr_add $(mtd_get_mac_binary mfginfo 29) +1)
+ ;;
asus,map-ac2200)
ath10kcal_ubi_extract "Factory" 20480 12064
;;
diff --git a/target/linux/ipq40xx/base-files/etc/inittab b/target/linux/ipq40xx/base-files/etc/inittab
index 809bba5e5ff49869429c91cf791cea73ab67d14e..3181021a0592720657b815c3eac803a57f4ea438 100644
--- a/target/linux/ipq40xx/base-files/etc/inittab
+++ b/target/linux/ipq40xx/base-files/etc/inittab
@@ -2,3 +2,4 @@
::sysinit:/etc/init.d/rcS S boot
::shutdown:/etc/init.d/rcS K shutdown
ttyMSM0::askfirst:/usr/libexec/login.sh
+ttyMSM1::askfirst:/usr/libexec/login.sh
diff --git a/target/linux/ipq40xx/base-files/lib/preinit/06_set_preinit_iface_ipq40xx.sh b/target/linux/ipq40xx/base-files/lib/preinit/06_set_preinit_iface_ipq40xx.sh
index be4b6322cb6a91f489dfec237ac6b79ce079e0eb..a0dec1042a3dd7416ece3307666c8ecf9d15d277 100644
--- a/target/linux/ipq40xx/base-files/lib/preinit/06_set_preinit_iface_ipq40xx.sh
+++ b/target/linux/ipq40xx/base-files/lib/preinit/06_set_preinit_iface_ipq40xx.sh
@@ -4,6 +4,7 @@ set_preinit_iface() {
. /lib/functions.sh
case $(board_name) in
+ aruba,ap-303| \
asus,rt-ac58u| \
avm,fritzbox-4040| \
glinet,gl-b1300| \
diff --git a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
index a7b7da1bf378f7cc19e960c497bc52efb3bae4fb..7253139497a8a8b9fab49cef3fce5eabe98d8002 100644
--- a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
@@ -48,6 +48,7 @@ platform_do_upgrade() {
case "$(board_name)" in
8dev,jalapeno |\
alfa-network,ap120c-ac |\
+ aruba,ap-303 |\
avm,fritzbox-7530 |\
avm,fritzrepeater-1200 |\
avm,fritzrepeater-3000 |\
diff --git a/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4029-ap-303.dts b/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4029-ap-303.dts
new file mode 100644
index 0000000000000000000000000000000000000000..7929494d027aca5c696910232a36d484f5ce6562
--- /dev/null
+++ b/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4029-ap-303.dts
@@ -0,0 +1,418 @@
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/soc/qcom,tcsr.h>
+
+/ {
+ model = "Aruba AP-303";
+ compatible = "aruba,ap-303";
+
+ aliases {
+ led-boot = &led_system_green;
+ led-failsafe = &led_system_red;
+ led-running = &led_system_green;
+ led-upgrade = &led_system_red;
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x80000000 0x10000000>;
+ };
+
+ soc {
+ mdio@90000 {
+ status = "okay";
+ pinctrl-0 = <&mdio_pins>;
+ pinctrl-names = "default";
+
+ /delete-node/ ethernet-phy@0;
+ /delete-node/ ethernet-phy@2;
+ /delete-node/ ethernet-phy@3;
+ /delete-node/ ethernet-phy@4;
+
+ ethernet-phy@5 {
+ reg = <0x5>;
+ };
+ };
+
+ counter@4a1000 {
+ compatible = "qcom,qca-gcnt";
+ reg = <0x4a1000 0x4>;
+ };
+
+ ess_tcsr@1953000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1953000 0x1000>;
+ qcom,ess-interface-select = <TCSR_ESS_PSGMII_RGMII5>;
+ };
+
+ tcsr@1949000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1949000 0x100>;
+ qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
+ };
+
+ tcsr@1957000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1957000 0x100>;
+ qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
+ };
+
+ blsp1_uart2: serial@78b0000 {
+ };
+
+ crypto@8e3a000 {
+ status = "okay";
+ };
+
+ watchdog@b017000 {
+ status = "okay";
+ };
+
+ ess-switch@c000000 {
+ switch_mac_mode = <0x3>; /* mac mode for RGMII RMII */
+ switch_lan_bmp = <0x0>; /* lan port bitmap */
+ switch_wan_bmp = <0x10>; /* wan port bitmap */
+ };
+
+ edma@c080000 {
+ qcom,single-phy;
+ qcom,num_gmac = <1>;
+ phy-mode = "rgmii-id";
+ status = "okay";
+ };
+
+ i2c_0: i2c@78b7000 {
+ pinctrl-0 = <&i2c_0_pins>;
+ pinctrl-names = "default";
+ status = "ok";
+
+ tpm@29 {
+ /* No Driver */
+ compatible = "atmel,at97sc3203";
+ reg = <0x29>;
+ read-only;
+ };
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ wifi_green {
+ label = "ap-303:green:wifi";
+ gpios = <&tlmm 39 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "phy0tpt";
+ };
+
+ wifi_amber {
+ label = "ap-303:amber:wifi";
+ gpios = <&tlmm 40 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "phy1tpt";
+ };
+
+ led_system_red: system_red {
+ label = "ap-303:red:system";
+ gpios = <&tlmm 46 GPIO_ACTIVE_HIGH>;
+ };
+
+ led_system_green: system_green {
+ label = "ap-303:green:system";
+ gpios = <&tlmm 47 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "Reset button";
+ gpios = <&tlmm 50 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+ };
+};
+
+&blsp_dma {
+ status = "okay";
+};
+
+&blsp1_uart1 {
+ /* Texas Instruments CC2540T BLE radio */
+ pinctrl-0 = <&serial_0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&blsp1_uart2 {
+ pinctrl-0 = <&serial_1_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&cryptobam {
+ status = "okay";
+};
+
+&gmac0 {
+ qcom,phy_mdio_addr = <5>;
+ qcom,poll_required = <1>;
+ vlan_tag = <0 0x20>;
+};
+
+&qpic_bam {
+ status = "okay";
+};
+
+&tlmm {
+ /*
+ * In addition to the Pins listed below,
+ * the following GPIOs have "features":
+ * 54 - out - active low to force HW reset
+ * 41 - out - active low to reset TPM
+ * 43 - out - active low to reset BLE radio
+ * 19 - in - active high when DC powered
+ */
+ mdio_pins: mdio_pinmux {
+ mux_1 {
+ pins = "gpio6";
+ function = "mdio";
+ bias-pull-up;
+ };
+ mux_2 {
+ pins = "gpio7";
+ function = "mdc";
+ bias-pull-up;
+ };
+ };
+
+ nand_pins: nand_pins {
+ pullups {
+ pins = "gpio53", "gpio58", "gpio59";
+ function = "qpic";
+ bias-pull-up;
+ };
+
+ pulldowns {
+ pins = "gpio54", "gpio55", "gpio56",
+ "gpio57", "gpio60", "gpio61",
+ "gpio62", "gpio63", "gpio64",
+ "gpio65", "gpio66", "gpio67",
+ "gpio68", "gpio69";
+ function = "qpic";
+ bias-pull-down;
+ };
+ };
+
+ spi_0_pins: spi_0_pinmux {
+ pin {
+ function = "blsp_spi0";
+ pins = "gpio13", "gpio14", "gpio15";
+ drive-strength = <12>;
+ bias-disable;
+ };
+ pin_cs {
+ function = "gpio";
+ pins = "gpio12";
+ drive-strength = <2>;
+ bias-disable;
+ output-high;
+ };
+ };
+ i2c_0_pins: i2c_0_pinmux {
+ mux {
+ pins = "gpio10", "gpio11";
+ function = "blsp_i2c0";
+ drive-strength = <4>;
+ bias-disable;
+ };
+ };
+
+ serial_0_pins: serial_0_pinmux {
+ mux {
+ pins = "gpio16", "gpio17";
+ function = "blsp_uart0";
+ bias-disable;
+ };
+ };
+
+ serial_1_pins: serial_1_pinmux {
+ mux {
+ pins = "gpio8", "gpio9";
+ function = "blsp_uart1";
+ bias-disable;
+ };
+ };
+
+ phy-reset {
+ line-name = "PHY-reset";
+ gpios = <42 GPIO_ACTIVE_HIGH>;
+ gpio-hog;
+ output-high;
+ };
+};
+
+&nand {
+ pinctrl-0 = <&nand_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ nand@0 {
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ /* 'aos0' in Aruba firmware */
+ label = "aos0";
+ reg = <0x0 0x2000000>;
+ read-only;
+ };
+
+ partition@2000000 {
+ /* 'aos1' in AVM firmware */
+ label = "ubi";
+ reg = <0x2000000 0x2000000>;
+ };
+
+ partition@4000000 {
+ label = "aruba-ubifs";
+ reg = <0x4000000 0x4000000>;
+ read-only;
+ };
+ };
+ };
+};
+
+&blsp1_spi1 {
+ pinctrl-0 = <&spi_0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ cs-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>;
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <24000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ /*
+ * There is no partition map for the NOR flash
+ * in the stock firmware.
+ *
+ * All partitions here are based on offsets
+ * found in the U-Boot GPL code and information
+ * from smem.
+ */
+
+ partition@0 {
+ label = "sbl1";
+ reg = <0x0 0x40000>;
+ read-only;
+ };
+
+ partition@40000 {
+ label = "mibib";
+ reg = <0x40000 0x20000>;
+ read-only;
+ };
+
+ partition@60000 {
+ label = "qsee";
+ reg = <0x60000 0x60000>;
+ read-only;
+ };
+
+ partition@c0000 {
+ label = "cdt";
+ reg = <0xc0000 0x10000>;
+ read-only;
+ };
+
+ partition@d0000 {
+ label = "ddrparams";
+ reg = <0xd0000 0x10000>;
+ read-only;
+ };
+
+ partition@e0000 {
+ label = "ART";
+ reg = <0xe0000 0x10000>;
+ read-only;
+ };
+
+ partition@f0000 {
+ label = "appsbl";
+ reg = <0xf0000 0xf0000>;
+ read-only;
+ };
+
+ partition@1e0000 {
+ label = "mfginfo";
+ reg = <0x1e0000 0x10000>;
+ read-only;
+ };
+
+ partition@1f0000 {
+ label = "apcd";
+ reg = <0x1f0000 0x10000>;
+ read-only;
+ };
+
+ partition@200000 {
+ label = "osss";
+ reg = <0x200000 0x180000>;
+ read-only;
+ };
+
+ partition@380000 {
+ /* This is empty */
+ label = "appsblenv";
+ reg = <0x380000 0x10000>;
+ read-only;
+ };
+
+ partition@390000 {
+ label = "pds";
+ reg = <0x390000 0x10000>;
+ read-only;
+ };
+
+ partition@3a0000 {
+ label = "fcache";
+ reg = <0x3a0000 0x10000>;
+ read-only;
+ };
+
+ partition@3b0000 {
+ /* Called osss1 in smem */
+ label = "u-boot-env-bak";
+ reg = <0x3b0000 0x10000>;
+ read-only;
+ };
+
+ partition@3f0000 {
+ label = "u-boot-env";
+ reg = <0x3f0000 0x10000>;
+ read-only;
+ };
+ };
+ };
+};
+
+&wifi0 {
+ status = "okay";
+ qcom,ath10k-calibration-variant = "Aruba-AP-303";
+};
+
+&wifi1 {
+ status = "okay";
+ qcom,ath10k-calibration-variant = "Aruba-AP-303";
+};
diff --git a/target/linux/ipq40xx/image/Makefile b/target/linux/ipq40xx/image/Makefile
index 98c81726d9c12bd466df2150c3e98a76cfb46f78..68dcbc59a42f6d8360b87c7b4e74cd34f697b465 100644
--- a/target/linux/ipq40xx/image/Makefile
+++ b/target/linux/ipq40xx/image/Makefile
@@ -85,6 +85,15 @@ define Device/alfa-network_ap120c-ac
endef
TARGET_DEVICES += alfa-network_ap120c-ac
+define Device/aruba_ap-303
+ $(call Device/FitImageLzma)
+ DEVICE_TITLE := Aruba AP-303
+ DEVICE_DTS := qcom-ipq4029-ap-303
+ DEVICE_PACKAGES := ipq-wifi-aruba_ap-303
+ IMAGES := sysupgrade.bin
+endef
+TARGET_DEVICES += aruba_ap-303
+
define Device/asus_map-ac2200
$(call Device/FitImageLzma)
DEVICE_DTS := qcom-ipq4019-map-ac2200
diff --git a/target/linux/ipq40xx/patches-4.14/304-mtd-spi-nor-Add-support-for-mx25r3235f.patch b/target/linux/ipq40xx/patches-4.14/304-mtd-spi-nor-Add-support-for-mx25r3235f.patch
new file mode 100644
index 0000000000000000000000000000000000000000..d95923a1610d4764538e79bb783702903edcdcad
--- /dev/null
+++ b/target/linux/ipq40xx/patches-4.14/304-mtd-spi-nor-Add-support-for-mx25r3235f.patch
@@ -0,0 +1,26 @@
+From 158acdbf0336f601971637f988b57a6a67a0869b Mon Sep 17 00:00:00 2001
+From: David Bauer <mail@david-bauer.net>
+Date: Sun, 15 Dec 2019 13:10:50 +0100
+Subject: [PATCH] mtd: spi-nor: Add support for mx25r3235f
+
+Add MTD support for the Macronix MX25R3235F SPI NOR chip from Macronix.
+The chip has 4MB of total capacity, divided into a total of 64 sectors,
+each 64KB sized. The chip also supports 4KB large sectors.
+Additionally, it supports dual and quad read modes.
+
+Signed-off-by: David Bauer <mail@david-bauer.net>
+---
+ drivers/mtd/spi-nor/spi-nor.c | 2 ++
+ 1 file changed, 2 insertions(+)
+
+--- a/drivers/mtd/spi-nor/spi-nor.c
++++ b/drivers/mtd/spi-nor/spi-nor.c
+@@ -1024,6 +1024,8 @@ static const struct flash_info spi_nor_i
+ { "mx25l3205d", INFO(0xc22016, 0, 64 * 1024, 64, SECT_4K) },
+ { "mx25l3255e", INFO(0xc29e16, 0, 64 * 1024, 64, SECT_4K) },
+ { "mx25l6405d", INFO(0xc22017, 0, 64 * 1024, 128, SECT_4K) },
++ { "mx25r3235f", INFO(0xc22816, 0, 64 * 1024, 64,
++ SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
+ { "mx25u3235f", INFO(0xc22536, 0, 64 * 1024, 64, 0) },
+ { "mx25u2033e", INFO(0xc22532, 0, 64 * 1024, 4, SECT_4K) },
+ { "mx25u4035", INFO(0xc22533, 0, 64 * 1024, 8, SECT_4K) },
diff --git a/target/linux/ipq40xx/patches-4.14/901-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-4.14/901-arm-boot-add-dts-files.patch
index f7efd415f1f1c000867793b3b133e44b3e50b0fd..fc8a88336491c2ac7c2a93fafb1f2b6fd38695be 100644
--- a/target/linux/ipq40xx/patches-4.14/901-arm-boot-add-dts-files.patch
+++ b/target/linux/ipq40xx/patches-4.14/901-arm-boot-add-dts-files.patch
@@ -10,7 +10,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
-@@ -697,7 +697,31 @@ dtb-$(CONFIG_ARCH_QCOM) += \
+@@ -697,7 +697,32 @@ dtb-$(CONFIG_ARCH_QCOM) += \
qcom-apq8074-dragonboard.dtb \
qcom-apq8084-ifc6540.dtb \
qcom-apq8084-mtp.dtb \
@@ -37,6 +37,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
+ qcom-ipq4019-qxwlan-e2600ac-c1.dtb \
+ qcom-ipq4019-qxwlan-e2600ac-c2.dtb \
+ qcom-ipq4028-wpj428.dtb \
++ qcom-ipq4029-ap-303.dtb \
+ qcom-ipq4029-gl-b1300.dtb \
+ qcom-ipq4029-mr33.dtb \
qcom-ipq8064-ap148.dtb \
Reference in New Issue Copy Permalink