gluon/patches/lede/0045-ar71xx-add-support-for-TP-LINK-Archer-C7-v4.patch

From: Felix Fietkau <nbd@nbd.name>
Date: Tue, 25 Jul 2017 13:32:47 +0200
Subject: ar71xx: add support for TP-LINK Archer C7 v4

TP-Link Archer C7 v4 is a dual-band AC1750 router, based on Qualcomm/Atheros
QCA9561+QCA9888.

Specification:

- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 3T3R 5 GHz
- 5x 10/100/1000 Mbps Ethernet
- 7x LED, 2x button
- UART header on PCB

Flash instruction:
1. Upload lede-ar71xx-generic-archer-c7-v4-squashfs-factory.bin via Web interface

Flash instruction using TFTP recovery:
1. Set PC to fixed ip address 192.168.0.66
2. Download lede-ar71xx-generic-archer-c7-v4-squashfs-factory.bin
and rename it to ArcherC7v4_tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.

Flash instruction under U-Boot, using UART:

1. tftp 0x81000000 lede-ar71xx-...-sysupgrade.bin
2. erase 0x9f040000 +$filesize
3. cp.b $fileaddr 0x9f040000 $filesize
4. reset

Signed-off-by: Felix Fietkau <nbd@nbd.name>

diff --git a/target/linux/ar71xx/base-files/etc/board.d/01_leds b/target/linux/ar71xx/base-files/etc/board.d/01_leds
index e67b5e38561e841b88e486341950c52e1d454322..44b1c2837e8392596eed14b4bc0d761042109715 100755
--- a/target/linux/ar71xx/base-files/etc/board.d/01_leds
+++ b/target/linux/ar71xx/base-files/etc/board.d/01_leds
@@ -53,7 +53,8 @@ ap121f)
 	ucidef_set_led_netdev "lan" "LAN" "$board:green:lan" "eth0"
 	ucidef_set_led_wlan "wlan" "WLAN" "$board:green:wlan" "phy0tpt"
 	;;
-archer-c25-v1)
+archer-c25-v1|\
+archer-c7-v4)
 	ucidef_set_led_netdev "wan" "WAN" "$board:green:wan" "eth0"
 	ucidef_set_led_wlan "wlan" "WLAN" "$board:green:wlan2g" "phy1tpt"
 	ucidef_set_led_wlan "wlan5g" "WLAN5G" "$board:green:wlan5g" "phy0tpt"
@@ -61,6 +62,12 @@ archer-c25-v1)
 	ucidef_set_led_switch "lan2" "LAN2" "$board:green:lan2" "switch0" "0x08"
 	ucidef_set_led_switch "lan3" "LAN3" "$board:green:lan3" "switch0" "0x04"
 	ucidef_set_led_switch "lan4" "LAN4" "$board:green:lan4" "switch0" "0x02"
+	case "$board" in
+		archer-c7-v4)
+			ucidef_set_led_usbdev "usb1" "USB1" "$board:green:usb1" "1-1"
+			ucidef_set_led_usbdev "usb2" "USB2" "$board:green:usb2" "2-1"
+		;;
+	esac
 	;;
 arduino-yun)
 	ucidef_set_led_wlan "wlan" "WLAN" "arduino:blue:wlan" "phy0tpt"
diff --git a/target/linux/ar71xx/base-files/etc/board.d/02_network b/target/linux/ar71xx/base-files/etc/board.d/02_network
index 454abe6a5005621967dd96e0282e7bce2a0b127e..86ac949bca12561536ce2c8adb190eb004c162e4 100755
--- a/target/linux/ar71xx/base-files/etc/board.d/02_network
+++ b/target/linux/ar71xx/base-files/etc/board.d/02_network
@@ -386,6 +386,7 @@ ar71xx_setup_interfaces()
 		ucidef_set_interface_wan "eth0"
 		ucidef_set_interface_raw "wlan" "wlan0" "dhcp"
 		;;
+	archer-c7-v4|\
 	tl-wdr4300|\
 	tl-wr1041n-v2)
 		ucidef_add_switch "switch0" \
diff --git a/target/linux/ar71xx/base-files/etc/diag.sh b/target/linux/ar71xx/base-files/etc/diag.sh
index 61db387c9ecefd7090c25a5f5d75fdbf65a44d65..97372bed0ea2fadfab10f22916a1e0d6a9c65725 100644
--- a/target/linux/ar71xx/base-files/etc/diag.sh
+++ b/target/linux/ar71xx/base-files/etc/diag.sh
@@ -51,6 +51,7 @@ get_status_led() {
 		status_led="ap135:green:status"
 		;;
 	archer-c25-v1|\
+	archer-c7-v4|\
 	mr12|\
 	mr16|\
 	nbg6616|\
diff --git a/target/linux/ar71xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ar71xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index 68f90de802ddd18e09a1da39c0d56292eea9489c..96b8f6b9a4bdd6a1609a819e72ade315bccfb3c0 100644
--- a/target/linux/ar71xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ar71xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -92,6 +92,7 @@ case "$FIRMWARE" in
 		ath10kcal_extract "art" 20480 2116
 		ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) -2)
 		;;
+	archer-c7-v4|\
 	archer-c25-v1|\
 	tl-wdr6500-v2)
 		ath10kcal_extract "art" 20480 2116
diff --git a/target/linux/ar71xx/base-files/lib/ar71xx.sh b/target/linux/ar71xx/base-files/lib/ar71xx.sh
index 8f8158bac8a28db4f4f15ce5c37f48a21084dc03..c32894d95b6b09b4b8b59ba64057c23e71b9f656 100755
--- a/target/linux/ar71xx/base-files/lib/ar71xx.sh
+++ b/target/linux/ar71xx/base-files/lib/ar71xx.sh
@@ -469,6 +469,9 @@ ar71xx_board_detect() {
 	*"Archer C5")
 		name="archer-c5"
 		;;
+	*"Archer C7 v4")
+		name="archer-c7-v4"
+		;;
 	*"Archer C7")
 		name="archer-c7"
 		;;
diff --git a/target/linux/ar71xx/base-files/lib/upgrade/platform.sh b/target/linux/ar71xx/base-files/lib/upgrade/platform.sh
index e748a2559cdb3a0ca6618429b0f613a656e39388..d414af969912894574e73e286ed5a3998532d34e 100755
--- a/target/linux/ar71xx/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ar71xx/base-files/lib/upgrade/platform.sh
@@ -207,6 +207,7 @@ platform_check_image() {
 	ap132|\
 	ap90q|\
 	archer-c25-v1|\
+	archer-c7-v4|\
 	bullet-m|\
 	c-55|\
 	carambola2|\
diff --git a/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt b/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt
index 7ad5419f51ec9909d8b59f33178221a7d81ec184..0a25294c40b5e2d3be825554ec7246a50b9c029b 100644
--- a/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt
+++ b/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt
@@ -1247,6 +1247,7 @@ config ATH79_MACH_ARCHER_C25_V1
 config ATH79_MACH_ARCHER_C7
 	bool "TP-LINK Archer C5/C7/TL-WDR4900 v2 board support"
 	select SOC_QCA955X
+	select SOC_QCA956X
 	select ATH79_DEV_AP9X_PCI if PCI
 	select ATH79_DEV_ETH
 	select ATH79_DEV_GPIO_BUTTONS
diff --git a/target/linux/ar71xx/files/arch/mips/ath79/Makefile b/target/linux/ar71xx/files/arch/mips/ath79/Makefile
index 3365a43ce16fc77b3212b39b92081efe678e8803..a0c73550eb0d5bf07ee731171be9e5ef9ff073e7 100644
--- a/target/linux/ar71xx/files/arch/mips/ath79/Makefile
+++ b/target/linux/ar71xx/files/arch/mips/ath79/Makefile
@@ -58,6 +58,7 @@ obj-$(CONFIG_ATH79_MACH_AP90Q)			+= mach-ap90q.o
 obj-$(CONFIG_ATH79_MACH_AP96)			+= mach-ap96.o
 obj-$(CONFIG_ATH79_MACH_ARCHER_C25_V1)		+= mach-archer-c25-v1.o
 obj-$(CONFIG_ATH79_MACH_ARCHER_C7)		+= mach-archer-c7.o
+obj-$(CONFIG_ATH79_MACH_ARCHER_C7)		+= mach-archer-c7-v4.o
 obj-$(CONFIG_ATH79_MACH_ARDUINO_YUN)		+= mach-arduino-yun.o
 obj-$(CONFIG_ATH79_MACH_AW_NR580)		+= mach-aw-nr580.o
 obj-$(CONFIG_ATH79_MACH_BHR_4GRV2)		+= mach-bhr-4grv2.o
diff --git a/target/linux/ar71xx/files/arch/mips/ath79/mach-archer-c7-v4.c b/target/linux/ar71xx/files/arch/mips/ath79/mach-archer-c7-v4.c
new file mode 100644
index 0000000000000000000000000000000000000000..64955c79945c0b2c28d5a93be6e45662200e60ed
--- /dev/null
+++ b/target/linux/ar71xx/files/arch/mips/ath79/mach-archer-c7-v4.c
@@ -0,0 +1,260 @@
+
+/*
+ * Atheros ARCHER_C7 reference board support
+ *
+ * Copyright (c) 2017 Felix Fietkau <nbd@nbd.name>
+ * Copyright (c) 2014 The Linux Foundation. All rights reserved.
+ * Copyright (c) 2012 Gabor Juhos <juhosg@openwrt.org>
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ *
+ */
+
+#include <linux/platform_device.h>
+#include <linux/ath9k_platform.h>
+#include <linux/ar8216_platform.h>
+#include <linux/proc_fs.h>
+#include <linux/gpio.h>
+#include <linux/spi/spi_gpio.h>
+#include <linux/spi/74x164.h>
+
+#include <asm/mach-ath79/ar71xx_regs.h>
+
+#include "common.h"
+#include "dev-m25p80.h"
+#include "machtypes.h"
+#include "pci.h"
+#include "dev-eth.h"
+#include "dev-gpio-buttons.h"
+#include "dev-leds-gpio.h"
+#include "dev-spi.h"
+#include "dev-usb.h"
+#include "dev-wmac.h"
+
+
+#define ARCHER_C7_GPIO_SHIFT_OE		1
+#define ARCHER_C7_GPIO_SHIFT_SER	14
+#define ARCHER_C7_GPIO_SHIFT_SRCLK	15
+#define ARCHER_C7_GPIO_SHIFT_RCLK	16
+#define ARCHER_C7_GPIO_SHIFT_SRCLR	21
+
+#define ARCHER_C7_GPIO_BTN_RESET	5
+#define ARCHER_C7_GPIO_BTN_WPS_WIFI	2
+
+#define ARCHER_C7_GPIO_LED_WLAN5	9
+#define ARCHER_C7_GPIO_LED_POWER	6
+#define ARCHER_C7_GPIO_LED_USB1		7
+#define ARCHER_C7_GPIO_LED_USB2		8
+
+#define ARCHER_C7_74HC_GPIO_BASE	QCA956X_GPIO_COUNT
+#define ARCHER_C7_GPIO_LED_WPS		(ARCHER_C7_74HC_GPIO_BASE + 0)
+#define ARCHER_C7_GPIO_LED_LAN1		(ARCHER_C7_74HC_GPIO_BASE + 1)
+#define ARCHER_C7_GPIO_LED_LAN2		(ARCHER_C7_74HC_GPIO_BASE + 2)
+#define ARCHER_C7_GPIO_LED_LAN3		(ARCHER_C7_74HC_GPIO_BASE + 3)
+#define ARCHER_C7_GPIO_LED_LAN4		(ARCHER_C7_74HC_GPIO_BASE + 4)
+#define ARCHER_C7_GPIO_LED_WAN_GREEN	(ARCHER_C7_74HC_GPIO_BASE + 5)
+#define ARCHER_C7_GPIO_LED_WAN_AMBER	(ARCHER_C7_74HC_GPIO_BASE + 6)
+#define ARCHER_C7_GPIO_LED_WLAN2	(ARCHER_C7_74HC_GPIO_BASE + 7)
+
+#define ARCHER_C7_KEYS_POLL_INTERVAL        20     /* msecs */
+#define ARCHER_C7_KEYS_DEBOUNCE_INTERVAL    (3 * ARCHER_C7_KEYS_POLL_INTERVAL)
+
+#define ARCHER_C7_MAC0_OFFSET               0
+#define ARCHER_C7_MAC1_OFFSET               6
+#define ARCHER_C7_WMAC_CALDATA_OFFSET       0x1000
+
+#define ARCHER_C7_GPIO_MDC			3
+#define ARCHER_C7_GPIO_MDIO			4
+
+static struct spi_gpio_platform_data archer_c7_v4_spi_data = {
+	.sck		= ARCHER_C7_GPIO_SHIFT_SRCLK,
+	.miso		= SPI_GPIO_NO_MISO,
+	.mosi		= ARCHER_C7_GPIO_SHIFT_SER,
+	.num_chipselect	= 1,
+};
+
+static u8 archer_c7_v4_ssr_initdata __initdata = 0xff;
+
+static struct gen_74x164_chip_platform_data archer_c7_v4_ssr_data = {
+	.base = ARCHER_C7_74HC_GPIO_BASE,
+	.num_registers = 1,
+	.init_data = &archer_c7_v4_ssr_initdata,
+};
+
+static struct platform_device archer_c7_v4_spi_device = {
+	.name		= "spi_gpio",
+	.id		= 1,
+	.dev = {
+		.platform_data = &archer_c7_v4_spi_data,
+	},
+};
+
+static struct spi_board_info archer_c7_v4_spi_info[] = {
+	{
+		.bus_num		= 1,
+		.chip_select		= 0,
+		.max_speed_hz		= 10000000,
+		.modalias		= "74x164",
+		.platform_data		= &archer_c7_v4_ssr_data,
+		.controller_data	= (void *) ARCHER_C7_GPIO_SHIFT_RCLK,
+	},
+};
+
+static struct gpio_led archer_c7_v4_leds_gpio[] __initdata = {
+	{
+		.name		= "archer-c7-v4:green:power",
+		.gpio		= ARCHER_C7_GPIO_LED_POWER,
+		.active_low	= 1,
+	}, {
+		.name		= "archer-c7-v4:green:wps",
+		.gpio		= ARCHER_C7_GPIO_LED_WPS,
+		.active_low	= 1,
+	}, {
+		.name		= "archer-c7-v4:green:wlan2g",
+		.gpio		= ARCHER_C7_GPIO_LED_WLAN2,
+		.active_low	= 1,
+	}, {
+		.name		= "archer-c7-v4:green:wlan5g",
+		.gpio		= ARCHER_C7_GPIO_LED_WLAN5,
+		.active_low	= 1,
+	}, {
+		.name		= "archer-c7-v4:green:lan1",
+		.gpio		= ARCHER_C7_GPIO_LED_LAN1,
+		.active_low	= 1,
+	}, {
+		.name		= "archer-c7-v4:green:lan2",
+		.gpio		= ARCHER_C7_GPIO_LED_LAN2,
+		.active_low	= 1,
+	}, {
+		.name		= "archer-c7-v4:green:lan3",
+		.gpio		= ARCHER_C7_GPIO_LED_LAN3,
+		.active_low	= 1,
+	}, {
+		.name		= "archer-c7-v4:green:lan4",
+		.gpio		= ARCHER_C7_GPIO_LED_LAN4,
+		.active_low	= 1,
+	}, {
+		.name		= "archer-c7-v4:green:wan",
+		.gpio		=  ARCHER_C7_GPIO_LED_WAN_GREEN,
+		.active_low	= 1,
+	}, {
+		.name		= "archer-c7-v4:amber:wan",
+		.gpio		=  ARCHER_C7_GPIO_LED_WAN_AMBER,
+		.active_low	= 1,
+	}, {
+		.name		= "archer-c7-v4:green:usb1",
+		.gpio		=  ARCHER_C7_GPIO_LED_USB1,
+		.active_low	= 1,
+	}, {
+		.name		= "archer-c7-v4:green:usb2",
+		.gpio		=  ARCHER_C7_GPIO_LED_USB2,
+		.active_low	= 1,
+	},
+};
+
+static struct gpio_keys_button archer_c7_v4_gpio_keys[] __initdata = {
+        {
+                .desc           = "WPS and WIFI button",
+                .type           = EV_KEY,
+                .code           = KEY_WPS_BUTTON,
+                .debounce_interval = ARCHER_C7_KEYS_DEBOUNCE_INTERVAL,
+                .gpio           = ARCHER_C7_GPIO_BTN_WPS_WIFI,
+                .active_low     = 1,
+        },
+        {
+                .desc           = "Reset button",
+                .type           = EV_KEY,
+                .code           = KEY_RESTART,
+                .debounce_interval = ARCHER_C7_KEYS_DEBOUNCE_INTERVAL,
+                .gpio           = ARCHER_C7_GPIO_BTN_RESET,
+                .active_low     = 1,
+        },
+};
+
+static struct ar8327_pad_cfg archer_c7_v4_ar8337_pad0_cfg = {
+	.mode = AR8327_PAD_MAC_SGMII,
+	.sgmii_delay_en = true,
+};
+
+static struct ar8327_platform_data archer_c7_v4_ar8337_data = {
+	.pad0_cfg = &archer_c7_v4_ar8337_pad0_cfg,
+	.port0_cfg = {
+		.force_link = 1,
+		.speed = AR8327_PORT_SPEED_1000,
+		.duplex = 1,
+		.txpause = 1,
+		.rxpause = 1,
+	},
+};
+
+static struct mdio_board_info archer_c7_v4_mdio0_info[] = {
+	{
+		.bus_id = "ag71xx-mdio.0",
+		.phy_addr = 0,
+		.platform_data = &archer_c7_v4_ar8337_data,
+	},
+};
+
+
+static void __init archer_c7_v4_setup(void)
+{
+	u8 *art = (u8 *) KSEG1ADDR(0x1fff0000);
+	u8 *mac = (u8 *) KSEG1ADDR(0x1ff00008);
+
+	ath79_register_m25p80(NULL);
+
+	spi_register_board_info(archer_c7_v4_spi_info,
+				ARRAY_SIZE(archer_c7_v4_spi_info));
+
+	platform_device_register(&archer_c7_v4_spi_device);
+
+	gpio_request_one(ARCHER_C7_GPIO_SHIFT_OE,
+			 GPIOF_OUT_INIT_LOW | GPIOF_EXPORT_DIR_FIXED,
+			 "LED control");
+
+	gpio_request_one(ARCHER_C7_GPIO_SHIFT_SRCLR,
+			 GPIOF_OUT_INIT_HIGH | GPIOF_EXPORT_DIR_FIXED,
+			 "LED reset");
+
+	ath79_register_leds_gpio(-1, ARRAY_SIZE(archer_c7_v4_leds_gpio),
+				archer_c7_v4_leds_gpio);
+
+	ath79_register_gpio_keys_polled(-1, ARCHER_C7_KEYS_POLL_INTERVAL,
+					ARRAY_SIZE(archer_c7_v4_gpio_keys),
+					archer_c7_v4_gpio_keys);
+
+	ath79_register_usb();
+
+	ath79_gpio_output_select(ARCHER_C7_GPIO_MDC, QCA956X_GPIO_OUT_MUX_GE0_MDC);
+	ath79_gpio_output_select(ARCHER_C7_GPIO_MDIO, QCA956X_GPIO_OUT_MUX_GE0_MDO);
+
+	ath79_register_mdio(0, 0x0);
+
+	mdiobus_register_board_info(archer_c7_v4_mdio0_info,
+				    ARRAY_SIZE(archer_c7_v4_mdio0_info));
+
+	ath79_register_wmac(art + ARCHER_C7_WMAC_CALDATA_OFFSET, mac);
+	ath79_register_pci();
+
+	/* GMAC0 is connected to an AR8337 switch */
+	ath79_init_mac(ath79_eth0_data.mac_addr, mac, 0);
+	ath79_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_SGMII;
+	ath79_eth0_data.speed = SPEED_1000;
+	ath79_eth0_data.duplex = DUPLEX_FULL;
+	ath79_eth0_data.phy_mask = BIT(0);
+	ath79_eth0_data.mii_bus_dev = &ath79_mdio0_device.dev;
+	ath79_register_eth(0);
+}
+
+MIPS_MACHINE(ATH79_MACH_ARCHER_C7_V4, "ARCHER-C7-V4", "TP-LINK Archer C7 v4",
+	     archer_c7_v4_setup);
diff --git a/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h b/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h
index 9cb4a7f2e1df641232289721b676a9b0149c76e5..e4623fd08836d59ad4e79e96f02e75e502a55ca6 100644
--- a/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h
+++ b/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h
@@ -44,6 +44,7 @@ enum ath79_mach_type {
 	ATH79_MACH_ARCHER_C5,			/* TP-LINK Archer C5 board */
 	ATH79_MACH_ARCHER_C7,			/* TP-LINK Archer C7 board */
 	ATH79_MACH_ARCHER_C7_V2,		/* TP-LINK Archer C7 V2 board */
+	ATH79_MACH_ARCHER_C7_V4,		/* TP-LINK Archer C7 V4 board */
 	ATH79_MACH_ARDUINO_YUN,			/* Yun */
 	ATH79_MACH_AW_NR580,			/* AzureWave AW-NR580 */
 	ATH79_MACH_BHR_4GRV2,			/* Buffalo BHR-4GRV2 */
diff --git a/target/linux/ar71xx/image/tp-link.mk b/target/linux/ar71xx/image/tp-link.mk
index 5be7cbfbd4ab7d73d679d52d2581459250e04302..27d6c73454aef96e5da47033ec664d2caffca1d5 100644
--- a/target/linux/ar71xx/image/tp-link.mk
+++ b/target/linux/ar71xx/image/tp-link.mk
@@ -298,6 +298,22 @@ define Device/archer-c7-v2
     IMAGE/factory-eu.bin := append-rootfs | mktplinkfw factory -C EU
 endef
 
+define Device/archer-c7-v4
+  DEVICE_TITLE := TP-LINK Archer C7 v4
+  DEVICE_PACKAGES := kmod-ath10k ath10k-firmware-qca988x
+  BOARDNAME := ARCHER-C7-V4
+  TPLINK_BOARD_NAME := ARCHER-C7-V4
+  IMAGE_SIZE := 15104k
+  LOADER_TYPE := elf
+  KERNEL := kernel-bin | patch-cmdline | lzma | uImageArcher lzma
+  IMAGES := sysupgrade.bin factory.bin
+  IMAGE/sysupgrade.bin := append-rootfs | tplink-safeloader sysupgrade | \
+	append-metadata | check-size $$$$(IMAGE_SIZE)
+  IMAGE/factory.bin := append-rootfs | tplink-safeloader factory
+  MTDPARTS := spi0.0:128k(factory-uboot)ro,128k(u-boot)ro,1536k(kernel),13568k(rootfs),960k(config)ro,64k(art)ro,15104k@0x40000(firmware)
+  SUPPORTED_DEVICES := archer-c7-v4
+endef
+
 define Device/archer-c7-v2-il
     $(Device/tplink-16mlzma)
     DEVICE_TITLE := TP-LINK Archer C7 v2 IL
@@ -316,7 +332,7 @@ define Device/tl-wdr7500-v3
     DEVICE_PROFILE := ARCHERC7
     TPLINK_HWID := 0x75000003
 endef
-TARGET_DEVICES += archer-c5-v1 archer-c7-v1 archer-c7-v2 archer-c7-v2-il tl-wdr7500-v3
+TARGET_DEVICES += archer-c5-v1 archer-c7-v1 archer-c7-v2 archer-c7-v2-il archer-c7-v4 tl-wdr7500-v3
 
 define Device/tl-mr10u-v1
     $(Device/tplink-4mlzma)
diff --git a/tools/firmware-utils/src/tplink-safeloader.c b/tools/firmware-utils/src/tplink-safeloader.c
index 478d5d8e9b43bbe37694732c138048c8fe8d807c..fec830c23ce6707755ddefc849f195872be1e877 100644
--- a/tools/firmware-utils/src/tplink-safeloader.c
+++ b/tools/firmware-utils/src/tplink-safeloader.c
@@ -376,6 +376,49 @@ static struct device_info boards[] = {
 		.last_sysupgrade_partition = "file-system"
 	},
 
+	/** Firmware layout for the C7 */
+	{
+		.id = "ARCHER-C7-V4",
+		.support_list =
+			"SupportList:\n"
+			"{product_name:Archer C7,product_ver:4.0.0,special_id:45550000}\n"
+			"{product_name:Archer C7,product_ver:4.0.0,special_id:55530000}\n"
+			"{product_name:Archer C7,product_ver:4.0.0,special_id:43410000}\n",
+		.support_trail = '\x00',
+		.soft_ver = "soft_ver:1.0.0\n",
+
+		/**
+		    We use a bigger os-image partition than the stock images (and thus
+		    smaller file-system), as our kernel doesn't fit in the stock firmware's
+		    1MB os-image.
+		*/
+		.partitions = {
+			{"factory-boot", 0x00000, 0x20000},
+			{"fs-uboot", 0x20000, 0x20000},
+			{"os-image", 0x40000, 0x180000},	/* Stock: base 0x40000 size 0x120000 */
+			{"file-system", 0x1c0000, 0xd40000},	/* Stock: base 0x160000 size 0xda0000 */
+			{"default-mac", 0xf00000, 0x00200},
+			{"pin", 0xf00200, 0x00200},
+			{"device-id", 0xf00400, 0x00100},
+			{"product-info", 0xf00500, 0x0fb00},
+			{"soft-version", 0xf10000, 0x00100},
+			{"extra-para", 0xf11000, 0x01000},
+			{"support-list", 0xf12000, 0x0a000},
+			{"profile", 0xf1c000, 0x04000},
+			{"default-config", 0xf20000, 0x10000},
+			{"user-config", 0xf30000, 0x40000},
+			{"qos-db", 0xf70000, 0x40000},
+			{"certificate", 0xfb0000, 0x10000},
+			{"partition-table", 0xfc0000, 0x10000},
+			{"log", 0xfd0000, 0x20000},
+			{"radio", 0xff0000, 0x10000},
+			{NULL, 0, 0}
+		},
+
+		.first_sysupgrade_partition = "os-image",
+		.last_sysupgrade_partition = "file-system",
+	},
+
 	/** Firmware layout for the C9 */
 	{
 		.id = "ARCHERC9",
@@ -929,6 +972,9 @@ static void build_image(const char *output,
 	    strcasecmp(info->id, "TLWR1043NV5") == 0) {
 		const char mdat[11] = {0x00, 0x00, 0x00, 0x02, 0x00, 0x00, 0x00, 0x00, 0x01, 0x00, 0x00};
 		parts[5] = put_data("extra-para", mdat, 11);
+	} else if (strcasecmp(info->id, "ARCHER-C7-V4") == 0) {
+		const char mdat[11] = {0x01, 0x00, 0x00, 0x02, 0x00, 0x00, 0xca, 0x00, 0x01, 0x00, 0x00};
+		parts[5] = put_data("extra-para", mdat, 11);
 	}
 
 	size_t len;