ath79-generic: Add support for OpenMesh A60
Device specifications:
======================
* Qualcomm/Atheros QCA9558 ver 1 rev 0
* 720/600/240 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 3T3R 2.4 GHz Wi-Fi (11n)
* 3T3R 5 GHz Wi-Fi (11ac)
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default))
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x ethernet
- eth0
+ Label: Ethernet 1
+ AR8035 ethernet PHY (RGMII)
+ 10/100/1000 Mbps Ethernet
+ 802.3af POE
+ used as WAN interface
- eth1
+ Label: Ethernet 2
+ AR8031 ethernet PHY (SGMII)
+ 10/100/1000 Mbps Ethernet
+ used as LAN interface
* 1x USB
* internal antennas
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to the
device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
This commit is contained in:
Sven Eckelmann
parent
a3203b26c4
commit
df114faec0
@ -33,6 +33,10 @@ ath79-generic
|
|||||||
|
|
||||||
- Omega [#modular_ethernet]_
|
- Omega [#modular_ethernet]_
|
||||||
|
|
||||||
|
* OpenMesh
|
||||||
|
|
||||||
|
- A60
|
||||||
|
|
||||||
* Plasma Cloud
|
* Plasma Cloud
|
||||||
|
|
||||||
- PA300
|
- PA300
|
||||||
|
|||||||
337
patches/openwrt/0005-ath79-Add-support-for-OpenMesh-A60.patch
Normal file
337
patches/openwrt/0005-ath79-Add-support-for-OpenMesh-A60.patch
Normal file
@ -0,0 +1,337 @@
|
|||||||
|
From: Sven Eckelmann <sven@narfation.org>
|
||||||
|
Date: Mon, 23 Nov 2020 13:41:34 +0100
|
||||||
|
Subject: ath79: Add support for OpenMesh A60
|
||||||
|
|
||||||
|
Device specifications:
|
||||||
|
======================
|
||||||
|
|
||||||
|
* Qualcomm/Atheros QCA9558 ver 1 rev 0
|
||||||
|
* 720/600/240 MHz (CPU/DDR/AHB)
|
||||||
|
* 128 MB of RAM
|
||||||
|
* 16 MB of SPI NOR flash
|
||||||
|
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
|
||||||
|
* 3T3R 2.4 GHz Wi-Fi (11n)
|
||||||
|
* 3T3R 5 GHz Wi-Fi (11ac)
|
||||||
|
* multi-color LED (controlled via red/green/blue GPIOs)
|
||||||
|
* 1x GPIO-button (reset)
|
||||||
|
* external h/w watchdog (enabled by default))
|
||||||
|
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
|
||||||
|
* 2x ethernet
|
||||||
|
- eth0
|
||||||
|
+ Label: Ethernet 1
|
||||||
|
+ AR8035 ethernet PHY (RGMII)
|
||||||
|
+ 10/100/1000 Mbps Ethernet
|
||||||
|
+ 802.3af POE
|
||||||
|
+ used as WAN interface
|
||||||
|
- eth1
|
||||||
|
+ Label: Ethernet 2
|
||||||
|
+ AR8031 ethernet PHY (SGMII)
|
||||||
|
+ 10/100/1000 Mbps Ethernet
|
||||||
|
+ used as LAN interface
|
||||||
|
* 1x USB
|
||||||
|
* internal antennas
|
||||||
|
|
||||||
|
Flashing instructions:
|
||||||
|
======================
|
||||||
|
|
||||||
|
Various methods can be used to install the actual image on the flash.
|
||||||
|
Two easy ones are:
|
||||||
|
|
||||||
|
ap51-flash
|
||||||
|
----------
|
||||||
|
|
||||||
|
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
|
||||||
|
used to transfer the image to the u-boot when the device boots up.
|
||||||
|
|
||||||
|
initramfs from TFTP
|
||||||
|
-------------------
|
||||||
|
|
||||||
|
The serial console must be used to access the u-boot shell during bootup.
|
||||||
|
It can then be used to first boot up the initramfs image from a TFTP server
|
||||||
|
(here with the IP 192.168.1.21):
|
||||||
|
|
||||||
|
setenv serverip 192.168.1.21
|
||||||
|
setenv ipaddr 192.168.1.1
|
||||||
|
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
|
||||||
|
|
||||||
|
The actual sysupgrade image can then be transferred (on the LAN port) to the
|
||||||
|
device via
|
||||||
|
|
||||||
|
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
|
||||||
|
|
||||||
|
On the device, the sysupgrade must then be started using
|
||||||
|
|
||||||
|
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
|
||||||
|
|
||||||
|
Signed-off-by: Sven Eckelmann <sven@narfation.org>
|
||||||
|
(cherry picked from commit eaf2e32c12655d7fb58e158086a784393dc6f69a)
|
||||||
|
|
||||||
|
diff --git a/package/boot/uboot-envtools/files/ath79 b/package/boot/uboot-envtools/files/ath79
|
||||||
|
index abcb99663dfd8e5d1ad0ee757e17972d63c856c7..0791d58b04cd108fcd2190bcf3c39f715f0b511f 100644
|
||||||
|
--- a/package/boot/uboot-envtools/files/ath79
|
||||||
|
+++ b/package/boot/uboot-envtools/files/ath79
|
||||||
|
@@ -49,6 +49,7 @@ netgear,wnr2200-16m|\
|
||||||
|
netgear,wnr612-v2|\
|
||||||
|
ocedo,koala|\
|
||||||
|
ocedo,raccoon|\
|
||||||
|
+openmesh,a60|\
|
||||||
|
openmesh,mr600-v1|\
|
||||||
|
openmesh,mr600-v2|\
|
||||||
|
openmesh,mr900-v1|\
|
||||||
|
diff --git a/target/linux/ath79/dts/qca9558_openmesh_a60.dts b/target/linux/ath79/dts/qca9558_openmesh_a60.dts
|
||||||
|
new file mode 100644
|
||||||
|
index 0000000000000000000000000000000000000000..473f055b492f6dffb0c460fd13e7ad9b604373c6
|
||||||
|
--- /dev/null
|
||||||
|
+++ b/target/linux/ath79/dts/qca9558_openmesh_a60.dts
|
||||||
|
@@ -0,0 +1,8 @@
|
||||||
|
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||||
|
+
|
||||||
|
+#include "qca9558_openmesh_a60.dtsi"
|
||||||
|
+
|
||||||
|
+/ {
|
||||||
|
+ compatible = "openmesh,a60", "qca,qca9558";
|
||||||
|
+ model = "OpenMesh A60";
|
||||||
|
+};
|
||||||
|
diff --git a/target/linux/ath79/dts/qca9558_openmesh_a60.dtsi b/target/linux/ath79/dts/qca9558_openmesh_a60.dtsi
|
||||||
|
new file mode 100644
|
||||||
|
index 0000000000000000000000000000000000000000..9938e5f4c013575c686edce5699f3541942133d3
|
||||||
|
--- /dev/null
|
||||||
|
+++ b/target/linux/ath79/dts/qca9558_openmesh_a60.dtsi
|
||||||
|
@@ -0,0 +1,180 @@
|
||||||
|
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||||
|
+
|
||||||
|
+#include "qca955x.dtsi"
|
||||||
|
+
|
||||||
|
+#include <dt-bindings/gpio/gpio.h>
|
||||||
|
+#include <dt-bindings/input/input.h>
|
||||||
|
+
|
||||||
|
+/ {
|
||||||
|
+ chosen {
|
||||||
|
+ /delete-property/ bootargs;
|
||||||
|
+ };
|
||||||
|
+
|
||||||
|
+ aliases {
|
||||||
|
+ serial0 = &uart;
|
||||||
|
+ led-boot = &led_status_green;
|
||||||
|
+ led-failsafe = &led_status_green;
|
||||||
|
+ led-running = &led_status_green;
|
||||||
|
+ led-upgrade = &led_status_green;
|
||||||
|
+ label-mac-device = ð0;
|
||||||
|
+ };
|
||||||
|
+
|
||||||
|
+ keys {
|
||||||
|
+ compatible = "gpio-keys";
|
||||||
|
+
|
||||||
|
+ reset {
|
||||||
|
+ label = "reset";
|
||||||
|
+ linux,code = <KEY_RESTART>;
|
||||||
|
+ gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
|
||||||
|
+ };
|
||||||
|
+ };
|
||||||
|
+
|
||||||
|
+ leds {
|
||||||
|
+ compatible = "gpio-leds";
|
||||||
|
+
|
||||||
|
+ status_blue {
|
||||||
|
+ label = "blue:status";
|
||||||
|
+ gpios = <&gpio 13 GPIO_ACTIVE_HIGH>;
|
||||||
|
+ };
|
||||||
|
+
|
||||||
|
+ status_red {
|
||||||
|
+ label = "red:status";
|
||||||
|
+ gpios = <&gpio 22 GPIO_ACTIVE_HIGH>;
|
||||||
|
+ };
|
||||||
|
+
|
||||||
|
+ led_status_green: status_green {
|
||||||
|
+ label = "green:status";
|
||||||
|
+ gpios = <&gpio 23 GPIO_ACTIVE_HIGH>;
|
||||||
|
+ };
|
||||||
|
+ };
|
||||||
|
+
|
||||||
|
+ watchdog {
|
||||||
|
+ compatible = "linux,wdt-gpio";
|
||||||
|
+ gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
|
||||||
|
+ hw_algo = "toggle";
|
||||||
|
+ /* hw_margin_ms is actually 300s but driver limits it to 60s */
|
||||||
|
+ hw_margin_ms = <60000>;
|
||||||
|
+ always-running;
|
||||||
|
+ };
|
||||||
|
+};
|
||||||
|
+
|
||||||
|
+&usb_phy1 {
|
||||||
|
+ status = "okay";
|
||||||
|
+};
|
||||||
|
+
|
||||||
|
+&usb1 {
|
||||||
|
+ status = "okay";
|
||||||
|
+};
|
||||||
|
+
|
||||||
|
+&spi {
|
||||||
|
+ status = "okay";
|
||||||
|
+
|
||||||
|
+ flash@0 {
|
||||||
|
+ compatible = "jedec,spi-nor";
|
||||||
|
+ reg = <0>;
|
||||||
|
+ spi-max-frequency = <40000000>;
|
||||||
|
+
|
||||||
|
+ /* partitions are passed via bootloader */
|
||||||
|
+ partitions {
|
||||||
|
+ compatible = "fixed-partitions";
|
||||||
|
+ #address-cells = <1>;
|
||||||
|
+ #size-cells = <1>;
|
||||||
|
+
|
||||||
|
+ partition@0 {
|
||||||
|
+ label = "u-boot";
|
||||||
|
+ reg = <0x000000 0x040000>;
|
||||||
|
+ read-only;
|
||||||
|
+ };
|
||||||
|
+
|
||||||
|
+ partition@40000 {
|
||||||
|
+ label = "u-boot-env";
|
||||||
|
+ reg = <0x040000 0x010000>;
|
||||||
|
+ };
|
||||||
|
+
|
||||||
|
+ partition@50000 {
|
||||||
|
+ label = "custom";
|
||||||
|
+ reg = <0x050000 0x060000>;
|
||||||
|
+ read-only;
|
||||||
|
+ };
|
||||||
|
+
|
||||||
|
+ partition@b0000 {
|
||||||
|
+ label = "inactive";
|
||||||
|
+ reg = <0x0b0000 0x7a0000>;
|
||||||
|
+ };
|
||||||
|
+
|
||||||
|
+ partition@850000 {
|
||||||
|
+ label = "inactive2";
|
||||||
|
+ reg = <0x850000 0x7a0000>;
|
||||||
|
+ };
|
||||||
|
+
|
||||||
|
+ art: partition@ff0000 {
|
||||||
|
+ label = "ART";
|
||||||
|
+ reg = <0xff0000 0x010000>;
|
||||||
|
+ read-only;
|
||||||
|
+ };
|
||||||
|
+ };
|
||||||
|
+ };
|
||||||
|
+};
|
||||||
|
+
|
||||||
|
+&mdio0 {
|
||||||
|
+ status = "okay";
|
||||||
|
+
|
||||||
|
+ phy-mask = <0x6>;
|
||||||
|
+
|
||||||
|
+ phy1: ethernet-phy@1 {
|
||||||
|
+ reg = <1>;
|
||||||
|
+ eee-broken-100tx;
|
||||||
|
+ eee-broken-1000t;
|
||||||
|
+ };
|
||||||
|
+
|
||||||
|
+ phy2: ethernet-phy@2 {
|
||||||
|
+ reg = <2>;
|
||||||
|
+ eee-broken-100tx;
|
||||||
|
+ eee-broken-1000t;
|
||||||
|
+ at803x-override-sgmii-link-check;
|
||||||
|
+ };
|
||||||
|
+};
|
||||||
|
+
|
||||||
|
+ð0 {
|
||||||
|
+ status = "okay";
|
||||||
|
+
|
||||||
|
+ pll-data = <0x82000101 0x80000101 0x80001313>;
|
||||||
|
+
|
||||||
|
+ mtd-mac-address = <&art 0x0>;
|
||||||
|
+
|
||||||
|
+ phy-mode = "rgmii-id";
|
||||||
|
+ phy-handle = <&phy1>;
|
||||||
|
+
|
||||||
|
+ gmac-config {
|
||||||
|
+ device = <&gmac>;
|
||||||
|
+ rgmii-enabled = <1>;
|
||||||
|
+ rxd-delay = <3>;
|
||||||
|
+ rxdv-delay = <3>;
|
||||||
|
+ txd-delay = <0>;
|
||||||
|
+ txen-delay = <0>;
|
||||||
|
+ };
|
||||||
|
+};
|
||||||
|
+
|
||||||
|
+ð1 {
|
||||||
|
+ status = "okay";
|
||||||
|
+
|
||||||
|
+ pll-data = <0x03000101 0x80000101 0x80001313>;
|
||||||
|
+
|
||||||
|
+ mtd-mac-address = <&art 0x6>;
|
||||||
|
+
|
||||||
|
+ qca955x-sgmii-fixup;
|
||||||
|
+
|
||||||
|
+ phy-handle = <&phy2>;
|
||||||
|
+};
|
||||||
|
+
|
||||||
|
+&wmac {
|
||||||
|
+ status = "okay";
|
||||||
|
+
|
||||||
|
+ mtd-cal-data = <&art 0x1000>;
|
||||||
|
+ mtd-mac-address = <&art 0x0>;
|
||||||
|
+ mtd-mac-address-increment = <2>;
|
||||||
|
+};
|
||||||
|
+
|
||||||
|
+&pcie0 {
|
||||||
|
+ status = "okay";
|
||||||
|
+};
|
||||||
|
diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network b/target/linux/ath79/generic/base-files/etc/board.d/02_network
|
||||||
|
index d4f53e7dae16b84955d318b9d79b6912ee156bdb..4b83ac7d32fc372cd3b493e8ec427c04e0f2e0d1 100755
|
||||||
|
--- a/target/linux/ath79/generic/base-files/etc/board.d/02_network
|
||||||
|
+++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network
|
||||||
|
@@ -172,6 +172,7 @@ ath79_setup_interfaces()
|
||||||
|
comfast,cf-e120a-v3|\
|
||||||
|
comfast,cf-e314n-v2|\
|
||||||
|
compex,wpj531-16m|\
|
||||||
|
+ openmesh,a60|\
|
||||||
|
openmesh,om2p-v4|\
|
||||||
|
openmesh,om2p-hs-v4|\
|
||||||
|
plasmacloud,pa300|\
|
||||||
|
diff --git a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
|
||||||
|
index 69735f336070a48ddad76c72c2876bcd775c56a1..b4c8a78a7fe4ba5bd3ca1f9c6e2b5e51e7fd1882 100644
|
||||||
|
--- a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
|
||||||
|
+++ b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
|
||||||
|
@@ -99,6 +99,7 @@ case "$FIRMWARE" in
|
||||||
|
caldata_extract "art" 0x5000 0x844
|
||||||
|
ath10k_patch_mac $(mtd_get_mac_binary art 0xc)
|
||||||
|
;;
|
||||||
|
+ openmesh,a60|\
|
||||||
|
openmesh,mr1750-v1|\
|
||||||
|
openmesh,mr1750-v2|\
|
||||||
|
openmesh,om5p-ac-v2)
|
||||||
|
diff --git a/target/linux/ath79/generic/base-files/lib/upgrade/platform.sh b/target/linux/ath79/generic/base-files/lib/upgrade/platform.sh
|
||||||
|
index 1240ef51e88ed2e5d24088746596da085c01ab5c..f7862bb032fbce56be77e9db8ae2e37bf5da30ea 100644
|
||||||
|
--- a/target/linux/ath79/generic/base-files/lib/upgrade/platform.sh
|
||||||
|
+++ b/target/linux/ath79/generic/base-files/lib/upgrade/platform.sh
|
||||||
|
@@ -65,6 +65,7 @@ platform_do_upgrade() {
|
||||||
|
jjplus,ja76pf2)
|
||||||
|
redboot_fis_do_upgrade "$1" linux
|
||||||
|
;;
|
||||||
|
+ openmesh,a60|\
|
||||||
|
openmesh,mr600-v1|\
|
||||||
|
openmesh,mr600-v2|\
|
||||||
|
openmesh,mr900-v1|\
|
||||||
|
diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk
|
||||||
|
index 304e58980062465ba7955e5fe45dbd6b0097937b..c669eb2cdb3f868c320412801723ceb112b4089f 100644
|
||||||
|
--- a/target/linux/ath79/image/generic.mk
|
||||||
|
+++ b/target/linux/ath79/image/generic.mk
|
||||||
|
@@ -1640,6 +1640,16 @@ define Device/openmesh_common_256k
|
||||||
|
openmesh-image ce_type=$$$$(OPENMESH_CE_TYPE) | append-metadata
|
||||||
|
endef
|
||||||
|
|
||||||
|
+define Device/openmesh_a60
|
||||||
|
+ $(Device/openmesh_common_64k)
|
||||||
|
+ SOC := qca9558
|
||||||
|
+ DEVICE_MODEL := A60
|
||||||
|
+ DEVICE_PACKAGES += kmod-ath10k-ct ath10k-firmware-qca988x-ct kmod-usb2
|
||||||
|
+ OPENMESH_CE_TYPE := A60
|
||||||
|
+ SUPPORTED_DEVICES += a60
|
||||||
|
+endef
|
||||||
|
+TARGET_DEVICES += openmesh_a60
|
||||||
|
+
|
||||||
|
define Device/openmesh_mr600-v1
|
||||||
|
$(Device/openmesh_common_64k)
|
||||||
|
SOC := ar9344
|
||||||
@ -88,6 +88,15 @@ device('ocedo-raccoon', 'ocedo_raccoon', {
|
|||||||
-- setup via integrated (USB-)tty is possible as well
|
-- setup via integrated (USB-)tty is possible as well
|
||||||
device('onion-omega', 'onion_omega')
|
device('onion-omega', 'onion_omega')
|
||||||
|
|
||||||
|
|
||||||
|
-- OpenMesh
|
||||||
|
|
||||||
|
device('openmesh-a60', 'openmesh_a60', {
|
||||||
|
packages = ATH10K_PACKAGES_QCA9880,
|
||||||
|
factory = false,
|
||||||
|
})
|
||||||
|
|
||||||
|
|
||||||
-- Plasma Cloud
|
-- Plasma Cloud
|
||||||
|
|
||||||
device('plasma-cloud-pa300', 'plasmacloud_pa300')
|
device('plasma-cloud-pa300', 'plasmacloud_pa300')
|
||||||
|
|||||||
Loading…
Reference in New Issue
Block a user