Merge pull request #1858 from freifunk-gluon/drop-ibss

Drop IBSS support

Makefile

@@ -40,10 +40,9 @@ $(eval $(call mkabspath,GLUON_TARGETSDIR))
 $(eval $(call mkabspath,GLUON_PATCHESDIR))
 
 GLUON_MULTIDOMAIN ?= 0
-GLUON_WLAN_MESH ?= 11s
 GLUON_DEBUG ?= 0
 
-export GLUON_RELEASE GLUON_REGION GLUON_MULTIDOMAIN GLUON_WLAN_MESH GLUON_DEBUG GLUON_DEPRECATED GLUON_DEVICES \
+export GLUON_RELEASE GLUON_REGION GLUON_MULTIDOMAIN GLUON_DEBUG GLUON_DEPRECATED GLUON_DEVICES \
 	 GLUON_TARGETSDIR GLUON_PATCHESDIR GLUON_TMPDIR GLUON_IMAGEDIR GLUON_PACKAGEDIR
 
 show-release:

docs/dev/mac_addresses.rst

@@ -10,9 +10,9 @@ Gluon tries to solve this issue by using a hash of the primary MAC address as a
 
 * 0: client0; WAN
 * 1: mesh0
-* 2: ibss0
+* 2: (unused)
 * 3: wan_radio0 (private WLAN); batman-adv primary address
 * 4: client1; LAN
 * 5: mesh1
-* 6: ibss1
+* 6: (unused)
 * 7: wan_radio1 (private WLAN); mesh VPN

docs/features/multidomain.rst

@@ -198,8 +198,6 @@ domain.conf only variables
 
       -  must be a random value used to derive the vxlan id for wired meshing
 
-   -  wifi*.ibss.ssid
-   -  wifi*.ibss.bssid
    -  wifi*.mesh.id
    -  mesh_vpn.fastd.groups.*.peers.remotes
    -  mesh_vpn.fastd.groups.*.peers.key

docs/features/wlan-configuration.rst

@@ -2,10 +2,9 @@ WLAN configuration
 ==================
 
 Gluon allows to configure 2.4GHz and 5GHz radios independently. The configuration
-may include any or all of the three networks "client" (AP mode), "mesh" (802.11s
-mode) and "ibss" (adhoc mode), which can be used simultaneously (using "mesh" and
-"ibss" at same time should be avoided though as weaker hardware usually can't handle the additional
-load). See :doc:`../user/site` for details on the configuration.
+may include one or both of the two networks "client" (AP mode) and "mesh" (802.11s
+mode), which can be used simultaneously. See :doc:`../user/site` for details on the
+configuration.
 
 Upgrade behaviour
 -----------------
@@ -16,15 +15,6 @@ on upgrades the existing setting is always retained (as this setting may have be
 by the user). This means that it is not possible to enable or disable an existing network
 configurations during upgrades.
 
-For the "mesh" and "ibss" networks, the default setting only has an effect if none
-of the two has existed before. If a new configuration has been added for "mesh" or "ibss",
-while the other of the two has already existed before, the enabled/disabled state of the
-existing configuration will also be set for the new configuration.
-
-This allows upgrades to change from IBSS to 11s and vice-versa while retaining the
-"wireless meshing is enabled/disabled" property configured by the user regardless
-of the used mode.
-
 During upgrades the wifi channel of the 2.4GHz and 5GHz radio will be restored to the channel
 configured in the site.conf. If you need to preserve a user defined wifi channel during upgrades
 you can configure this via the uci section ``gluon-core.wireless``::

docs/package/gluon-scheduled-domain-switch.rst

@@ -3,7 +3,7 @@ gluon-scheduled-domain-switch
 
 This package allows to switch a routers domain at a given point
 in time. This is needed for switching between incompatible transport
-protocols (e.g. 802.11s and IBSS or VXLAN).
+protocols (e.g. wired meshing with and without VXLAN).
 
 Nodes will switch when the defined *switch-time* has passed. In case the node was
 powered off while this was supposed to happen, it might not be able to acquire the

docs/user/site.rst

@@ -120,12 +120,11 @@ wifi24 \: optional
     WLAN configuration for 2.4 GHz devices.
     ``channel`` must be set to a valid wireless channel for your radio.
 
-    There are currently three interface types available. You may choose to
+    There are currently two interface types available. You may choose to
     configure any subset of them:
 
     - ``ap`` creates a master interface where clients may connect
     - ``mesh`` creates an 802.11s mesh interface with forwarding disabled
-    - ``ibss`` creates an ad-hoc interface
 
     Each interface may be disabled by setting ``disabled`` to ``true``.
     This will only affect new installations.
@@ -139,10 +138,7 @@ wifi24 \: optional
     don't want users to connect to this mesh-SSID, so use a cryptic id that no
     one will accidentally mistake for the client WiFi.
 
-    ``ibss`` requires two parameters: ``ssid`` (a string) and ``bssid`` (a MAC).
-    An optional parameter ``vlan`` (integer) is supported.
-
-    Both ``mesh`` and ``ibss`` accept an optional ``mcast_rate`` (kbit/s) parameter for
+    ``mesh`` also accepts an optional ``mcast_rate`` (kbit/s) parameter for
     setting the multicast bitrate. Increasing the default value of 1000 to something
     like 12000 is recommended.
     ::
@@ -156,11 +152,6 @@ wifi24 \: optional
            id = 'ueH3uXjdp',
            mcast_rate = 12000,
          },
-         ibss = {
-           ssid = 'ff:ff:ff:ee:ba:be',
-           bssid = 'ff:ff:ff:ee:ba:be',
-           mcast_rate = 12000,
-         },
        },
 
 .. _user-site-wifi5:
@@ -559,11 +550,6 @@ GLUON_LANGS
     List of languages (as two-letter-codes) to be included in the web interface. Should always contain
     ``en``.
 
-GLUON_WLAN_MESH
-  Setting this to ``11s`` or ``ibss`` will enable generation of matching images for devices which don't
-  support both meshing modes, either at all (e.g. ralink and mediatek don't support AP+IBSS) or in the
-  same firmware (ath10k-based 5GHz). Defaults to ``11s``.
-
 .. _user-site-feature-flags:
 
 Feature flags

docs/user/supported_devices.rst

@@ -41,7 +41,7 @@ ar71xx-generic
 
   - GL-AR150
   - GL-AR300M
-  - GL-AR750 [#ath10k]_
+  - GL-AR750
   - GL-iNet 6408A (v1)
   - GL-iNet 6416A (v1)
 
@@ -57,7 +57,7 @@ ar71xx-generic
 
 * OCEDO
 
-  - Koala [#ath10k]_
+  - Koala
 
 * OpenMesh
 
@@ -65,24 +65,24 @@ ar71xx-generic
   - A60
   - MR600 (v1, v2)
   - MR900 (v1, v2)
-  - MR1750 (v1, v2) [#ath10k]_
+  - MR1750 (v1, v2)
   - OM2P (v1, v2, v4)
   - OM2P-HS (v1, v2, v3, v4)
   - OM2P-LC
   - OM5P
   - OM5P-AN
-  - OM5P-AC (v1, v2) [#ath10k]_
+  - OM5P-AC (v1, v2)
 
 * TP-Link
 
-  - Archer C5 (v1) [#ath10k]_
-  - Archer C59 (v1) [#80211s]_
-  - Archer C7 (v2, v4, v5) [#ath10k]_
+  - Archer C5 (v1)
+  - Archer C59 (v1)
+  - Archer C7 (v2, v4, v5)
   - CPE210 (v1.0, v1.1, v2.0, v3.0)
   - CPE220 (v1.1)
   - CPE510 (v1.0, v1.1)
   - CPE520 (v1.1)
-  - RE450 [#ath10k]_
+  - RE450
   - TL-WDR3500 (v1)
   - TL-WDR3600 (v1)
   - TL-WDR4300 (v1)
@@ -109,12 +109,12 @@ ar71xx-generic
   - Rocket M2/M5
   - Rocket M2/M5 Ti
   - Rocket M2/M5 XW
-  - UniFi AC Mesh [#ath10k]_
-  - UniFi AC Mesh Pro [#ath10k]_
+  - UniFi AC Mesh
+  - UniFi AC Mesh Pro
   - UniFi AP
-  - UniFi AP AC Lite [#ath10k]_
-  - UniFi AP AC LR [#ath10k]_
-  - UniFi AP AC Pro [#ath10k]_
+  - UniFi AP AC Lite
+  - UniFi AP AC LR
+  - UniFi AP AC Pro
   - UniFi AP LR
   - UniFi AP Pro
   - UniFi AP Outdoor
@@ -127,7 +127,7 @@ ar71xx-generic
 
 * ZyXEL
 
-  - NBG6616 [#ath10k]_
+  - NBG6616
 
 ar71xx-nand
 -----------
@@ -143,7 +143,7 @@ ar71xx-nand
 
 * ZyXEL
 
-  - NBG6716 [#ath10k]_
+  - NBG6716
 
 ar71xx-tiny [#deprecated]_
 --------------------------
@@ -191,8 +191,8 @@ brcm2708-bcm2709
 * RaspberryPi 2
 
 
-ipq40xx-generic [#80211s]_
---------------------------
+ipq40xx-generic
+---------------
 
 * AVM
 
@@ -217,8 +217,8 @@ ipq40xx-generic [#80211s]_
   - NBG6617
   - WRE6606
 
-ipq806x-generic [#80211s]_
---------------------------
+ipq806x-generic
+---------------
 
 * NETGEAR
 
@@ -249,8 +249,8 @@ mpc85xx-p1020
 
   - Panda
 
-ramips-mt7620 [#80211s]_
-------------------------
+ramips-mt7620
+-------------
 
 * GL Innovations
 
@@ -267,11 +267,11 @@ ramips-mt7621
 
 * ASUS
 
-  - RT-AC57U [#80211s]_
+  - RT-AC57U
 
 * D-Link
 
-  - DIR-860L (B1) [#80211s]_
+  - DIR-860L (B1)
 
 * Ubiquiti
 
@@ -280,11 +280,11 @@ ramips-mt7621
 
 * ZBT
 
-  - WG3526-16M [#80211s]_
-  - WG3526-32M [#80211s]_
+  - WG3526-16M
+  - WG3526-32M
 
-ramips-mt76x8 [#80211s]_
-------------------------
+ramips-mt76x8
+-------------
 
 * GL.iNet
 
@@ -306,8 +306,8 @@ ramips-mt76x8 [#80211s]_
 
   - VoCore2
 
-ramips-rt305x [#80211s]_ [#deprecated]_
----------------------------------------
+ramips-rt305x [#deprecated]_
+----------------------------
 
 * A5-V11
 
@@ -358,14 +358,5 @@ Footnotes
   The device or target is reaching its end of life soon. This means that support
   in the next major release of Gluon is doubtful.
 
-.. [#ath10k]
-  Device uses the ath10k WLAN driver. Images are built for 11s by default unless GLUON_WLAN_MESH
-  is set as described in :ref:`getting-started-make-variables`.
-
-.. [#80211s]
-  Device or target does not support IBSS. Images are built by default unless
-  GLUON_WLAN_MESH is explicitly set to something other than *11s*. Targets that
-  are affected as a whole may not be selected for build in this case.
-
 .. [#avmflash]
   For instructions on how to flash AVM devices, visit https://fritzfla.sh

package/gluon-core/check_site.lua

@@ -49,14 +49,7 @@ for _, config in ipairs({'wifi24', 'wifi5'}) do
 
 		obsolete({config, 'supported_rates'}, '802.11b rates are disabled by default.')
 		obsolete({config, 'basic_rate'}, '802.11b rates are disabled by default.')
-
-		if need_table({config, 'ibss'}, nil, false) then
-			need_string_match(in_domain({config, 'ibss', 'ssid'}), '^' .. ('.?'):rep(32) .. '$')
-			need_string_match(in_domain({config, 'ibss', 'bssid'}), '^%x[02468aAcCeE]:%x%x:%x%x:%x%x:%x%x:%x%x$')
-			need_one_of({config, 'ibss', 'mcast_rate'}, supported_rates, false)
-			need_number({config, 'ibss', 'vlan'}, false)
-			need_boolean({config, 'ibss', 'disabled'}, false)
-		end
+		obsolete({config, 'ibss'}, 'IBSS support has been dropped.')
 
 		if need_table({config, 'mesh'}, nil, false) then
 			need_string_match(in_domain({config, 'mesh', 'id'}), '^' .. ('.?'):rep(32) .. '$')

package/gluon-core/luasrc/lib/gluon/upgrade/200-wireless

@@ -98,49 +98,12 @@ local function first_non_nil(first, ...)
 end
 
 
-local function configure_ibss(config, radio, index, suffix, disabled)
-	local radio_name = radio['.name']
+local function delete_ibss(radio_name)
 	local name = 'ibss_' .. radio_name
 
 	uci:delete('network', name)
 	uci:delete('network', name .. '_vlan')
 	uci:delete('wireless', name)
-
-	if not config then
-		return
-	end
-
-	local macaddr = util.get_wlan_mac(uci, radio, index, 3)
-	if not macaddr then
-		return
-	end
-
-	if config.vlan then
-		uci:section('network', 'interface', name, {
-			proto = 'none',
-		})
-
-		uci:section('network', 'interface', name .. '_vlan', {
-			ifname = '@' .. name .. '.' .. config.vlan,
-			proto = 'gluon_mesh',
-		})
-	else
-		uci:section('network', 'interface', name, {
-			proto = 'gluon_mesh',
-		})
-	end
-
-	uci:section('wireless', 'wifi-iface', name, {
-		device = radio_name,
-		network = name,
-		mode = 'adhoc',
-		ssid = config.ssid,
-		bssid = config.bssid,
-		macaddr = macaddr,
-		mcast_rate = config.mcast_rate,
-		ifname = suffix and 'ibss' .. suffix,
-		disabled = disabled,
-	})
 end
 
 local function configure_mesh(config, radio, index, suffix, disabled)
@@ -202,20 +165,9 @@ local function configure_mesh_wireless(radio, index, config)
 	local radio_name = radio['.name']
 	local suffix = radio_name:match('^radio(%d+)$')
 
-	local ibss_disabled = is_disabled('ibss_' .. radio_name)
-	local mesh_disabled = is_disabled('mesh_' .. radio_name)
-
-	configure_ibss(config.ibss(), radio, index, suffix,
-		first_non_nil(
-			ibss_disabled,
-			mesh_disabled,
-			config.ibss.disabled(false)
-		)
-	)
 	configure_mesh(config.mesh(), radio, index, suffix,
 		first_non_nil(
-			mesh_disabled,
-			ibss_disabled,
+			is_disabled('mesh_' .. radio_name),
 			config.mesh.disabled(false)
 		)
 	)
@@ -224,6 +176,8 @@ end
 util.foreach_radio(uci, function(radio, index, config)
 	local radio_name = radio['.name']
 
+	delete_ibss(radio_name)
+
 	if not config() then
 		uci:set('wireless', radio_name, 'disabled', true)
 		return
@@ -259,7 +213,6 @@ util.foreach_radio(uci, function(radio, index, config)
 			util.add_to_set(hostapd_options, 'country3=0x4f')
 			uci:set_list('wireless', radio_name, 'hostapd_options', hostapd_options)
 
-			uci:delete('wireless', 'ibss_' .. radio_name)
 			uci:delete('wireless', 'mesh_' .. radio_name)
 		else
 			uci:delete('wireless', radio_name, 'channels')
@@ -277,12 +230,7 @@ end)
 
 
 if uci:get('system', 'rssid_wlan0') then
-	if uci:get('wireless', 'mesh_radio0') then
-		uci:set('system', 'rssid_wlan0', 'dev', 'mesh0')
-	else
-		uci:set('system', 'rssid_wlan0', 'dev', 'ibss0')
-	end
-
+	uci:set('system', 'rssid_wlan0', 'dev', 'mesh0')
 	uci:save('system')
 end
 

package/gluon-core/luasrc/usr/lib/lua/gluon/util.lua

@@ -172,11 +172,11 @@ end
 -- IDs defined so far:
 -- 0: client0; WAN
 -- 1: mesh0
--- 2: ibss0
+-- 2: (unused)
 -- 3: wan_radio0 (private WLAN); batman-adv primary address
 -- 4: client1; LAN
 -- 5: mesh1
--- 6: ibss1
+-- 6: (unused)
 -- 7: wan_radio1 (private WLAN); mesh VPN
 function M.generate_mac(i)
 	if i > 7 or i < 0 then return nil end -- max allowed id (0b111)

package/gluon-mesh-batman-adv/files/lib/gluon/core/mesh/setup.d/30-gluon-mesh-batman-adv

@@ -1,13 +1,5 @@
 #!/bin/sh
 
 if [ "$FIXED_MTU" -eq 0 ]; then
-	# In case on VLAN on IBSS, first set MTU of the underlying interface
-	for lower in /sys/class/net/"$IFNAME"/lower_*/wireless; do
-		lower="${lower%%\/wireless}"
-		lower="${lower##*\/lower_}"
-		ip link set dev "$lower" mtu 1536
-		break
-	done
-
 	ip link set dev "$IFNAME" mtu 1532
 fi

package/gluon-web-wifi-config/i18n/de.po

@@ -19,14 +19,33 @@ msgstr "2,4GHz-WLAN"
 msgid "5GHz WLAN"
 msgstr "5GHz-WLAN"
 
+msgid ""
+"Configuring the node for outdoor use tunes the 5 GHz radio to a frequency "
+"and transmission power that conforms with the local regulatory requirements. "
+"It also enables dynamic frequency selection (DFS; radar detection). At the "
+"same time, mesh functionality is disabled as it requires neighbouring nodes "
+"to stay on the same channel permanently."
+msgstr ""
+"Ist der Knoten für den Einsatz im Freien konfiguriert, wird ein WLAN-Kanal "
+"auf dem 5-GHz-Band sowie eine Sendeleistung entsprechend den gesetzlichen "
+"Frequenzregulatorien gewählt. Gleichzeitig wird die dynamische Frequenzwahl "
+"(DFS; Radarerkennung) aktiviert und die Mesh-Funktionalität deaktiviert, da "
+"sich Nachbarknoten dauerhaft auf demselben Kanal befinden müssen."
+
 msgid "Enable client network (access point)"
 msgstr "Client-Netz aktivieren (Access Point)"
 
 msgid "Enable mesh network (802.11s)"
 msgstr "Mesh-Netz aktivieren (802.11s)"
 
-msgid "Enable mesh network (IBSS)"
-msgstr "Mesh-Netz aktivieren (IBSS)"
+msgid "HT Mode"
+msgstr "HT-Modus"
+
+msgid "Node will be installed outdoors"
+msgstr "Knoten wird im Außenbereich betrieben"
+
+msgid "Outdoor Installation"
+msgstr "Outdoor-Installation"
 
 msgid "Transmission power"
 msgstr "Sendeleistung"
@@ -49,25 +68,3 @@ msgstr ""
 "werden. Wenn möglich, ist in den Werten der Sendeleistung der Antennengewinn "
 "enthalten; diese Werte sind allerdings für viele Geräte nicht verfügbar oder "
 "fehlerhaft."
-
-msgid "Outdoor installation"
-msgstr "Outdoor-Installation"
-
-msgid "Node will be installed outdoors"
-msgstr "Knoten wird im Außenbereich betrieben"
-
-msgid ""
-"Configuring the node for outdoor use tunes the 5 GHz radio to a frequency "
-"and transmission power that conforms with the local regulatory requirements. "
-"It also enables dynamic frequency selection (DFS; radar detection). At the "
-"same time, mesh functionality is disabled as it requires neighbouring nodes "
-"to stay on the same channel permanently."
-msgstr ""
-"Ist der Knoten für den Einsatz im Freien konfiguriert, wird ein WLAN-Kanal auf "
-"dem 5-GHz-Band sowie eine Sendeleistung entsprechend den gesetzlichen "
-"Frequenzregulatorien gewählt. Gleichzeitig wird die dynamische Frequenzwahl "
-"(DFS; Radarerkennung) aktiviert und die Mesh-Funktionalität deaktiviert, da "
-"sich Nachbarknoten dauerhaft auf demselben Kanal befinden müssen."
-
-msgid "HT Mode"
-msgstr "HT-Modus"

package/gluon-web-wifi-config/i18n/fr.po

@@ -1,14 +1,15 @@
 msgid ""
 msgstr ""
-"Content-Type: text/plain; charset=UTF-8\n"
 "Project-Id-Version: PACKAGE VERSION\n"
 "PO-Revision-Date: 2015-08-19 23:30+0100\n"
 "Last-Translator:Tobias Bernot <tqbs@airmail.cc>\n"
 "Language-Team: French\n"
 "Language: fr\n"
 "MIME-Version: 1.0\n"
+"Content-Type: text/plain; charset=UTF-8\n"
 "Content-Transfer-Encoding: 8bit\n"
 "Plural-Forms: nplurals=2; plural=(n != 1);\n"
+
 msgid "(default)"
 msgstr "(défaut)"
 
@@ -18,14 +19,28 @@ msgstr "2,4GHz Wi-Fi"
 msgid "5GHz WLAN"
 msgstr "5GHz Wi-Fi"
 
+msgid ""
+"Configuring the node for outdoor use tunes the 5 GHz radio to a frequency "
+"and transmission power that conforms with the local regulatory requirements. "
+"It also enables dynamic frequency selection (DFS; radar detection). At the "
+"same time, mesh functionality is disabled as it requires neighbouring nodes "
+"to stay on the same channel permanently."
+msgstr ""
+
 msgid "Enable client network (access point)"
 msgstr "Activer le réseau client (Access Point)"
 
 msgid "Enable mesh network (802.11s)"
 msgstr "Activer le réseau MESH (802.11s)"
 
-msgid "Enable mesh network (IBSS)"
-msgstr "Activer le réseau MESH (IBSS)"
+msgid "HT Mode"
+msgstr "Mode HT"
+
+msgid "Node will be installed outdoors"
+msgstr ""
+
+msgid "Outdoor Installation"
+msgstr "Installation extérieure"
 
 msgid "Transmission power"
 msgstr "Puissance d'émission"
@@ -41,14 +56,9 @@ msgid ""
 "values include the antenna gain where available, but there are many devices "
 "for which the gain is unavailable or inaccurate."
 msgstr ""
-"Ici vous pouvez activer ou désactiver la SSID du client ou MESH. "
-"Pensez a laisser la SSID du MESH activée pour que les autres nœuds puissent se connecter. "
-"<br /><br />Ici vous pouvez aussi configurer la puissance d'émmission se votre Wi-Fi. "
-"Prenez note que les valeurs fournies pour la puissance de transmission prennent "
-"en compte les gains fournis par l'antenne, et que ces valeurs ne sont pas toujours disponibles ou exactes."
-
-msgid "Outdoor installation"
-msgstr "Installation extérieure"
-
-msgid "HT Mode"
-msgstr "Mode HT"
+"Ici vous pouvez activer ou désactiver la SSID du client ou MESH. Pensez a "
+"laisser la SSID du MESH activée pour que les autres nœuds puissent se "
+"connecter. <br /><br />Ici vous pouvez aussi configurer la puissance "
+"d'émmission se votre Wi-Fi. Prenez note que les valeurs fournies pour la "
+"puissance de transmission prennent en compte les gains fournis par "
+"l'antenne, et que ces valeurs ne sont pas toujours disponibles ou exactes."

package/gluon-web-wifi-config/i18n/gluon-web-wifi-config.pot

@@ -10,13 +10,27 @@ msgstr ""
 msgid "5GHz WLAN"
 msgstr ""
 
+msgid ""
+"Configuring the node for outdoor use tunes the 5 GHz radio to a frequency "
+"and transmission power that conforms with the local regulatory requirements. "
+"It also enables dynamic frequency selection (DFS; radar detection). At the "
+"same time, mesh functionality is disabled as it requires neighbouring nodes "
+"to stay on the same channel permanently."
+msgstr ""
+
 msgid "Enable client network (access point)"
 msgstr ""
 
 msgid "Enable mesh network (802.11s)"
 msgstr ""
 
-msgid "Enable mesh network (IBSS)"
+msgid "HT Mode"
+msgstr ""
+
+msgid "Node will be installed outdoors"
+msgstr ""
+
+msgid "Outdoor Installation"
 msgstr ""
 
 msgid "Transmission power"
@@ -33,20 +47,3 @@ msgid ""
 "values include the antenna gain where available, but there are many devices "
 "for which the gain is unavailable or inaccurate."
 msgstr ""
-
-msgid "Outdoor installation"
-msgstr ""
-
-msgid "Node will be installed outdoors"
-msgstr ""
-
-msgid ""
-"Configuring the node for outdoor use tunes the 5 GHz radio to a frequency "
-"and transmission power that conforms with the local regulatory requirements. "
-"It also enables dynamic frequency selection (DFS; radar detection). At the "
-"same time, mesh functionality is disabled as it requires neighbouring nodes "
-"to stay on the same channel permanently."
-msgstr ""
-
-msgid "HT Mode"
-msgstr ""

package/gluon-web-wifi-config/luasrc/lib/gluon/config-mode/model/admin/wifi-config.lua

@@ -76,7 +76,6 @@ uci:foreach('wireless', 'wifi-device', function(config)
 
 	vif_option('client', translate('Enable client network (access point)'))
 	vif_option('mesh', translate("Enable mesh network (802.11s)"))
-	vif_option('ibss', translate("Enable mesh network (IBSS)"))
 
 	local phy = util.find_phy(config)
 	if not phy then

targets/ar71xx-generic

@@ -1,14 +1,24 @@
 config 'CONFIG_GLUON_SPECIALIZE_KERNEL=y'
 config 'CONFIG_TARGET_SQUASHFS_BLOCK_SIZE=64'
 
-local ATH10K_PACKAGES = {}
-local ATH10K_PACKAGES_QCA9887 = {}
-local ATH10K_PACKAGES_QCA9888 = {}
-if env.GLUON_WLAN_MESH == '11s' then
-	ATH10K_PACKAGES = {'kmod-ath10k', '-kmod-ath10k-ct', 'ath10k-firmware-qca988x', '-ath10k-firmware-qca988x-ct'}
-	ATH10K_PACKAGES_QCA9887 = {'kmod-ath10k', '-kmod-ath10k-ct', 'ath10k-firmware-qca9887', '-ath10k-firmware-qca9887-ct'}
-	ATH10K_PACKAGES_QCA9888 = {'kmod-ath10k', '-kmod-ath10k-ct', 'ath10k-firmware-qca9888', '-ath10k-firmware-qca9888-ct'}
-end
+local ATH10K_PACKAGES = {
+	'kmod-ath10k',
+	'-kmod-ath10k-ct',
+	'ath10k-firmware-qca988x',
+	'-ath10k-firmware-qca988x-ct',
+}
+local ATH10K_PACKAGES_QCA9887 = {
+	'kmod-ath10k',
+	'-kmod-ath10k-ct',
+	'ath10k-firmware-qca9887',
+	'-ath10k-firmware-qca9887-ct',
+}
+local ATH10K_PACKAGES_QCA9888 = {
+	'kmod-ath10k',
+	'-kmod-ath10k-ct',
+	'ath10k-firmware-qca9888',
+	'-ath10k-firmware-qca9888-ct',
+}
 
 
 -- 8devices
@@ -307,7 +317,6 @@ device('tp-link-archer-c58-v1', 'archer-c58-v1', {
 
 device('tp-link-archer-c59-v1', 'archer-c59-v1', {
 	packages = ATH10K_PACKAGES_QCA9888,
-	broken = (env.GLUON_WLAN_MESH ~= '11s'),
 })
 
 device('tp-link-archer-c60-v1', 'archer-c60-v1', {

targets/ar71xx-nand

@@ -1,9 +1,6 @@
 config 'CONFIG_GLUON_SPECIALIZE_KERNEL=y'
 
-local ATH10K_PACKAGES = {}
-if env.GLUON_WLAN_MESH == '11s' then
-	ATH10K_PACKAGES = {'kmod-ath10k', '-kmod-ath10k-ct', 'ath10k-firmware-qca988x', '-ath10k-firmware-qca988x-ct'}
-end
+local ATH10K_PACKAGES = {'kmod-ath10k', '-kmod-ath10k-ct', 'ath10k-firmware-qca988x', '-ath10k-firmware-qca988x-ct'}
 
 
 defaults {

targets/ipq40xx-generic

@@ -1,21 +1,17 @@
-local ATH10K_PACKAGES_IPQ40XX = {}
-local ATH10K_PACKAGES_IPQ40XX_QCA9888 = {}
-if env.GLUON_WLAN_MESH == '11s' then
-	ATH10K_PACKAGES_IPQ40XX = {
-		'kmod-ath10k',
-		'-kmod-ath10k-ct',
-		'ath10k-firmware-qca4019',
-		'-ath10k-firmware-qca4019-ct',
-	}
-	ATH10K_PACKAGES_IPQ40XX_QCA9888 = {
-		'kmod-ath10k',
-		'-kmod-ath10k-ct',
-		'ath10k-firmware-qca4019',
-		'-ath10k-firmware-qca4019-ct',
-		'ath10k-firmware-qca9888',
-		'-ath10k-firmware-qca9888-ct',
-	}
-end
+local ATH10K_PACKAGES_IPQ40XX = {
+	'kmod-ath10k',
+	'-kmod-ath10k-ct',
+	'ath10k-firmware-qca4019',
+	'-ath10k-firmware-qca4019-ct',
+}
+local ATH10K_PACKAGES_IPQ40XX_QCA9888 = {
+	'kmod-ath10k',
+	'-kmod-ath10k-ct',
+	'ath10k-firmware-qca4019',
+	'-ath10k-firmware-qca4019-ct',
+	'ath10k-firmware-qca9888',
+	'-ath10k-firmware-qca9888-ct',
+}
 
 
 defaults {

targets/ramips-mt7621

@@ -2,15 +2,12 @@
 
 device('asus-rt-ac57u', 'asus_rt-ac57u', {
 	factory = false,
-	broken = (env.GLUON_WLAN_MESH ~= '11s'),
 })
 
 
 -- D-Link
 
-device('d-link-dir-860l-b1', 'dir-860l-b1', {
-	broken = (env.GLUON_WLAN_MESH ~= '11s'),
-})
+device('d-link-dir-860l-b1', 'dir-860l-b1')
 
 
 -- Netgear
@@ -28,12 +25,10 @@ device('zbt-wg3526-16m', 'zbt-wg3526-16M', {
 	manifest_aliases = {
 		'zbt-wg3526',
 	},
-	broken = (env.GLUON_WLAN_MESH ~= '11s'),
 })
 
 device('zbt-wg3526-32m', 'zbt-wg3526-32M', {
 	factory = false,
-	broken = (env.GLUON_WLAN_MESH ~= '11s'),
 })
 
 

targets/sunxi-cortexa7

@@ -13,5 +13,5 @@ device('lemaker-banana-pro', 'sun7i-a20-bananapro', {
 })
 
 device('lamobo-r1', 'sun7i-a20-lamobo-r1', {
-	broken = true, -- AP+IBSS and AP+11s not working
+	broken = true, -- AP+11s not working
 })

targets/targets.mk

@@ -1,5 +1,3 @@
-GLUON_WLAN_MESH_11s := $(filter 11s,$(GLUON_WLAN_MESH))
-
 $(eval $(call GluonTarget,ar71xx,generic))
 ifneq ($(GLUON_DEPRECATED),0)
 $(eval $(call GluonTarget,ar71xx,tiny))
@@ -7,25 +5,23 @@ endif
 $(eval $(call GluonTarget,ar71xx,nand))
 $(eval $(call GluonTarget,brcm2708,bcm2708))
 $(eval $(call GluonTarget,brcm2708,bcm2709))
+$(eval $(call GluonTarget,ipq40xx,generic))
+$(eval $(call GluonTarget,ipq806x,generic))
 $(eval $(call GluonTarget,lantiq,xway))
 $(eval $(call GluonTarget,mpc85xx,generic))
 $(eval $(call GluonTarget,mpc85xx,p1020))
+$(eval $(call GluonTarget,ramips,mt7620))
 $(eval $(call GluonTarget,ramips,mt7621))
+$(eval $(call GluonTarget,ramips,mt76x8))
+$(eval $(call GluonTarget,ramips,rt305x))
 $(eval $(call GluonTarget,sunxi,cortexa7))
 $(eval $(call GluonTarget,x86,generic))
 $(eval $(call GluonTarget,x86,geode))
 $(eval $(call GluonTarget,x86,64))
 
-ifneq ($(GLUON_WLAN_MESH_11s)$(BROKEN),)
-$(eval $(call GluonTarget,ipq40xx,generic))
-$(eval $(call GluonTarget,ipq806x,generic))
-$(eval $(call GluonTarget,ramips,mt7620))
-$(eval $(call GluonTarget,ramips,mt76x8))
-$(eval $(call GluonTarget,ramips,rt305x))
-endif
 
 ifneq ($(BROKEN),)
 $(eval $(call GluonTarget,ar71xx,mikrotik)) # BROKEN: no sysupgrade support
 $(eval $(call GluonTarget,brcm2708,bcm2710)) # BROKEN: Untested
-$(eval $(call GluonTarget,mvebu,cortexa9)) # BROKEN: No AP+IBSS or 11s support
+$(eval $(call GluonTarget,mvebu,cortexa9)) # BROKEN: No 11s support
 endif

targets/x86.inc

@@ -1,11 +1,6 @@
 config 'CONFIG_VDI_IMAGES=y'
 config 'CONFIG_VMDK_IMAGES=y'
 
-local ATH10K_PACKAGES = {'kmod-ath10k-ct', 'ath10k-firmware-qca9887', 'ath10k-firmware-qca988x'}
-if env.GLUON_WLAN_MESH == 'ibss' then
-	ATH10K_PACKAGES = {'kmod-ath10k-ct', 'ath10k-firmware-qca9887-ct', 'ath10k-firmware-qca988x-ct'}
-end
-
 packages {
 	'kmod-3c59x',
 	'kmod-8139cp',
@@ -37,6 +32,7 @@ packages {
 	'kmod-usb2',
 	'kmod-usb3',
 	'kmod-usb-serial',
+	'kmod-ath10k',
+	'ath10k-firmware-qca9887',
+	'ath10k-firmware-qca988x',
 }
-
-packages(ATH10K_PACKAGES)