Before this commit the decision whether a vxlan layer will be
introduced between the lower interface before the interface is
added to batman was inside the proto. Now the decision is moved
to the user of the proto.
This device is a dual 5GHz device. It is recommended to manually change the
radio of the first device to the lower 5GHz channels and the second radio
to the upper 5GHz channels
This adds the OpenWrt label-mac device selection as the most preferred
fallback.
While this is only used on OpenWrt 19.07 for backports, we can also use
the label-mac device when backporting device support. This way, we have
to deal with less device-sepcific code downstream.
Signed-off-by: David Bauer <mail@david-bauer.net>
Specifications:
* SoC: MT7620A
* RAM: 64 MB DDR
* Flash: 8MB NOR SPI flash
* WiFi: MT7612E (5Ghz) and builtin MT7620A (2.4GHz)
* LAN: 1x100M
The -factory images can be flashed from the device's web
interface or via nmrpflash.
Both devices differ by a additional power outlet for the EX3800.
This patch has been tested on a EX3800 device.
This renames the local_client zone to loc_client, as local_clint exceeds
the maximum zone length allowed for firewall3, which is 11 bytes.
This worked previously due to firewall3 using unsafe string operations.
Now creation of the chain fails (latest OpenWrt master).
Reorder scripts so that the mesh_lan interface is accounted for.
Two other firewall upgrade scripts (mesh-babel and l3roamd) are
reordered as well. While there seems to be no hard dependency at the
moment, it makes sense to run the basic setup first, also to avoid
problems with future changes.
Closes: #2090
Fixes: ed094bc68c ("gluon-core: firewall: Allow custom gluon_wired interfaces (#2041)")
This will hide the outdoor mode setting on compatible devices in case
the defined channels should be preserved.
Otherwise a user might be under the impression their device is compliant
with outdoor operation when in reality it still uses prohibited
channels.
On lantiq, the default WAN ifname is 'dsl0' even on devices that have a
separate WAN port. At least on devices using swconfig we can override
this with the switch port labelled as 'wan'.
Because is_disabled() was always returning true or false, the
first_non_nil() would never actually check the default setting from
site.conf. This was broken since v2017.1.
Fixes: 6cf03bab37 ("treewide: replace normal uses of luci.model.uci with simple-uci to reduce LuCI dependencies")
The interfaces should always exist and just be disabled when outdoor
mode is enabled. Not creating them at all leads to an issue in the
advanced wifi settings where an additional reload of the page is
necessary after enabling or disabling the ourdoor mode to make the mesh
VIF options appear or disappear.
This allows for multiple mesh legs out of one box. Useful for offloaders
and networks using vlan for separate mesh transport.
Custom mesh interfaces in a VXLAN domain are otherwise firewalled.
This fixes#1479
This adds support for the beacon interval to be set on a per-band base.
This has the potential to reduce the amount of airtime used up for
sending beacon frames.
Separate wireless-related helper methods from the util module to a
new wireless module. This keeps them separated, as the amount of
wireless helpers increased in the past, justifying a separate module.
The netdev() lookup is confusing to use: whenever a interface does not
exist during boot (for example VLAN) or when the address is overridden
from board.json (which is not obvious at all), it will yield either no
address, or a different address than expected.
To avoid this confusion, using board.json-based interface() is
preferable. This converts all uses of netdev() to the corresponding
lan/wan lookups, except for the final fallback for eth0.
- Replace misnamed, closure-returning sysfs() to a reusable read() function
- Rename eth() to netdev(), pass full interface name
- Rename board() to interface()
- Split reuable get_netdev_addr() out of netdev()
gsub() returns the number of matches as its second return value. This
was unintendedly passed through by the util functions trim() and
node_id(). It can be presumed that this had no effect in practice, but
it can lead to surprising output when passing values to print() for
debugging.
This adds a helper method, which determines if the current platform
supports WPA3 or not.
WPA3 is supported if
- the device is not in the featureset category "tiny"
- the WiFi driver supports 802.11w management frame protection
Remove a lot of redundant code by switching to a match table listing
the targets and boards for each candidate for the primary MAC interface.
In addition, we add some flexiblity by allow to switch out the sysfs file
data source for the MAC address.
mac_to_ip() calculates an ipv6 address from a mac address according to
RFC 4291. For wireguard we have to use specially crafted addresses that
must be unique. This allows calculating such unique mac-based addresses
by allowing to optionally specifying the bytes to be inserted into the
address.
The is_outdoor function is placed inside the gluon.platform module, not
the platform_info module. Currently, the outdoor-mode wizard component
and the upgrade script fail due to nil-value calls.
Add the `wifi5.outdoor_chanlist` site configuration that
allows specifying an outdoor channel range that can be
switched to for regulatory compliance.
Upon enabling the outdoor option the device will
- configure the `outdoor_chanlist` on all 5 GHz radios
- which may enable DFS/TPC, based on the regulatory domain
- disable ibss/mesh on the 5 GHz radio, as DFS *will*
break mesh connections
- allow for htmode reconfiguration on 5 GHz radios
The outdoor option can be toggled from
- Advanced Settings
- W-LAN
- Outdoor Installation
The `preserve_channel` flag overrules the outdoor channel
selection.
The device is broken until the next release. The LEDs are currently not
working (fixed in current OpenWRT master).
Also give a brief explanation about the BROKEN status being dependent on
the WiFi chip used and not the SoC family in general.
Gluon has multiple ways to obtain unique MAC-addresses. They are either
provided by the WiFi driver or derived from the primary MAC-address.
Quoting the same file:
> It's necessary that the first 45 bits of the MAC address don't
> vary on a single hardware interface, since some chips are using
> a hardware MAC filter. (e.g 'rt305x')
This currently fails in case the rt35xx based chips mac address differs
from the primary MAC. In this case, the MAC address for the client0 radio
(vif 1) comes from the WiFi driver. As there is only a single
MAC-address provided by '/sys/class/ieee80211/phyX/addresses' but the
MAC-address for mesh 0 (vif 2) is derived from the Node-ID, resulting in
different first 45 bits. The WiFi won't come up altogether in this case.
This commit verifies at least 4 MAC-Addresses are provided by the WiFi
driver. If this is not the case, all MAC-addresses are derived from the
primary MAC. This way, affected radios are working correctly.
This commit distributes dualband radios evenly on 2.4 GHz and 5GHz with
2.4 GHz being prioritised higher than 5 GHz. This means in case a device
has only a single radio and this radio supports operation in both bands,
it will be set to 2.4 GHz.
Tested-by: Martin Weinelt <martin@darmstadt.freifunk.net>
Signed-off-by: David Bauer <mail@david-bauer.net>
This adds support for the TP-Link TL-WR902Ac v1 travel router.
The device is marked as broken due to 64MB which might be insufficient
in certain environments.
This reverts commit b3d7011130.
with this change, DNS in batman-adv based networks is broken.
although the revert breaks babel based networks, this is not as big of a problem.
This device is a dual 5GHz device. It is recommended to manually change the
radio of the first device to the lower 5GHz channels and the second radio
to the upper 5GHz channels.
In multidomain setups, VXLAN is enabled by default, but can be disabled in
domain configs using the mesh/vxlan option. In single domain setups, the
mesh/vxlan option is mandatory.
The UCI option for legacy mode is removed.
Fixes#1364
dnsmasq's caching is severly broken and does not handle all answer records
equally. In particular, its cached answers are missing DNSKEY and DS
records, breaking DNSSEC validation on clients.
Remove the cache for now. It may return if dnsmasq is fixed or we switch to
a different resolver.
net.ipv6.conf.br-client.forwarding is moved from gluon-client-bridge to
gluon-mesh-batman-adv, as the setting is not useful with non-bridged
protocols.
Both gluon.sysconfig and libgluonutil already remove the trailing newline
if it exists. It's nicer to avoid files without a trailing newline, e.g.
for printing the file contents in a terminal.
This should not convert JSON to a Lua table and back, as this loses the
distinction between arrays and objects, but as our site.conf is defined in
Lua anyways (for now), this can be fixed in a later revision.
[Matthias Schiffer: rename to gluon-show-site, rebase]
By basing the Lua gluon.site module on gluonutil_load_site_config(), the
config load implementation needs to changed only in a single place for
multi-domain support.
* gluon-core, gluon-client-bridge: introduce new firewall zone: local_client
* gluon-core: put clients in local_client zone, introduce drop-zone,
set dns-rules and zones
* gluon-respondd: allow respondd on mesh
* gluon-status-page-api: allow http input on mesh and client
The new gluon.site lua library will eventually replace gluon.site_config
(which is hereby deprecated, but will continue to be supported for a
while).
The new gluon.site library will wrap all values to allow traversing
non-existing tables without errors.
site = require 'gluon.site'
c = site.a.b.c -- doesn't fail even if a or a.b don't exist
The wrapped values must be unwrapped using call syntax:
site_name = site.site_name()
Using the call syntax on a non-existing value will return nil. An
alternative default value may be passed instead:
mac = site.next_node.mac('16:41:95:40:f7:dc')
