Hardware
--------
MediaTek MT7621AT
256M DDR3
32M SPI-NOR
MediaTek MT7603 2T2R 802.11n 2.4GHz
MediaTek MT7915 2T2R 802.11ax 5GHz
Not Working
-----------
- Bluetooth (connected to UART3)
UART
----
UART is located in the lower left corner of the board. Pinout is
0 - 3V3 (don't connect)
1 - RX
2 - TX
3 - GND
Console is 115200 8N1.
Boot
----
1. Connect to the serial console and connect power.
2. Double-press ESC when prompted
3. Set the fdt address
$ fdt addr $(fdtcontroladdr)
4. Remove the signature node from the control FDT
$ fdt rm /signature
5. Transfer and boot the OpenWrt initramfs image to the device.
Make sure to name the file C0A80114.img and have it reachable at
192.168.1.1/24
$ tftpboot; bootm
Installation
------------
1. Connect to the booted device at 192.168.1.20 using username/password
"ubnt".
2. Update the bootloader environment.
$ fw_setenv devmode TRUE
$ fw_setenv boot_openwrt "fdt addr \$(fdtcontroladdr);
fdt rm /signature; bootubnt"
$ fw_setenv bootcmd "run boot_openwrt"
3. Transfer the OpenWrt sysupgrade image to the device using SCP.
4. Check the mtd partition number for bs / kernel0 / kernel1
$ cat /proc/mtd
5. Set the bootselect flag to boot from kernel0
$ dd if=/dev/zero bs=1 count=1 of=/dev/mtdblock4
6. Write the OpenWrt sysupgrade image to both kernel0 as well as kernel1
$ dd if=openwrt.bin of=/dev/mtdblock6
$ dd if=openwrt.bin of=/dev/mtdblock7
7. Reboot the device. It should boot into OpenWrt.
* ath79-generic: add support for Onion Omega
support was previously dropped in
commit 45c84a117b ("ar71xx: drop target")
* fixup! ath79-generic: add support for Onion Omega
* fixup! ath79-generic: add support for Onion Omega
- [x] must be flashable from vendor firmware
- [ ] webinterface
- [ ] tftp
- [x] other: Console port available. Manufacturer specific cable required.
Tutorial in OpenWRT commit message https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=c6e972c8772a628a1a2f2e5590d7c6f4acef9ab0
- [x] must support upgrade mechanism
- [x] must have working sysupgrade
- [x] must keep/forget configuration (if applicable)
*think `sysupgrade [-n]` or `firstboot`*
- [x] must have working autoupdate
root@Aruba-AP-303H:~# lua -e 'print(require("platform_info").get_image_name())'
aruba-ap-303h
- [x] reset/wps/phone button must return device into config mode
- [x] primary mac should match address on device label (or packaging) (https://gluon.readthedocs.io/en/latest/dev/hardware.html#notes)
- wired network
- [x] should support all network ports on the device
- [x] must have correct port assignment (WAN/LAN)
- wifi (if applicable)
- [x] association with AP must be possible on all radios
- [x] association with 802.11s mesh must be working on all radios
- [x] ap/mesh mode must work in parallel on all radios
- led mapping
- power/sys led (_critical, because led definitions are setup on firstboot only_)
- [x] lit while the device is on
- [x] should display config mode blink sequence
(https://gluon.readthedocs.io/en/latest/features/configmode.html)
- radio leds
- [x] should map to their respective radio
- [x] should show activity
- switchport leds
- [x] should map to their respective port (or switch, if only one led present)
- [x] should show link state and activity
- outdoor devices only
- [ ] added board name to `is_outdoor_device` function in `package/gluon-core/luasrc/usr/lib/lua/gluon/platform.lua`
- ToDo (upstream):
- enable PoE pass through on interface E3
system.poe_passthrough=gpio_switch
system.poe_passthrough.name='PoE Passthrough'
system.poe_passthrough.gpio_pin='446'
system.poe_passthrough.value='0' (0 is active)
TP-Link RE200 v2 is a wireless range extender with Ethernet and 2.4G and 5G
WiFi with internal antennas. It's based on MediaTek MT7628AN+MT7610EN.
Specifications
--------------
- MediaTek MT7628AN (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 1T1R 5 GHz
- 1x 10/100 Mbps Ethernet
- UART header on PCB (57600 8n1)
- 8x LED (GPIO-controlled), 2x button
There are 2.4G and 5G LEDs in red and green which are controlled
separately.
MAC addresses
-------------
The MAC address assignment matches stock firmware, i.e.:
LAN : *:0D
2.4G: *:0E
5G : *:0F
Installation
------------
Web Interface
-------------
It is possible to upgrade to OpenWrt via the web interface. Simply flash
the -factory.bin from OEM. In contrast to a stock firmware, this will not
overwrite U-Boot.
VoCores aren't exactly useful mesh nodes except for experimentation.
They certainly aren't worth maintaining a whole target, in particular
one that has a WLAN driver not used by any other target.
Specifications:
- CPU: MediaTek MT7628AN (580MHz)
- Flash: 16MB
- RAM: 64MB DDR2
- 2.4 GHz: IEEE 802.11b/g/n with Integrated LNA and PA
- Antennas: 4x external single band antennas
- WAN: 1x 10/100M
- LAN: 2x 10/100M
- LEDs: 2x yellow/blue. Programmable (labelled as power on case)
- Non-programmable (shows WAN activity)
- Button: Reset
How to install:
1- Use OpenWRTInvasion to gain telnet and ftp access.
2- Push openwrt firmware to /tmp/ using ftp.
3- Connect to router using telnet. (IP: 192.168.31.1 -
Username: root - No password)
4- Use command "mtd -r write /tmp/firmware.bin OS1" to flash into
the router..
5- It takes around 2 minutes. After that router will restart itself
to OpenWrt.
Specifications:
- SoC: MediaTek MT7621
- Flash: 16 MiB NOR SPI
- RAM: 128 MiB DDR3
- Ethernet: 3x 10/100/1000 Mbps (switched, 2xLAN + WAN)
- WIFI0: MT7603E 2.4GHz 802.11b/g/n
- WIFI1: MT7612E 5GHz 802.11ac
- Antennas: 4x external (2 per radio), non-detachable
- LEDs: Programmable "power" LED (two-coloured, yellow/blue)
Non-programmable "internet" LED (shows WAN activity)
- Buttons: Reset
Installation:
Bootloader won't accept any serial input unless "boot_wait" u-boot
environment variable is changed to "on".
Vendor firmware won't accept any serial input until "uart_en" is
set to "1".
Using the https://github.com/acecilia/OpenWRTInvasion exploit you
can gain access to shell to enable these options:
To enable uart keyboard actions - 'nvram set uart_en=1'
To make uboot delay boot work - 'nvram set boot_wait=on'
Set boot delay to 5 - 'nvram set bootdelay=5'
Then run 'nvram commit' to make the changes permanent.
Once in the shell (following the OpenWRTInvasion instructions) you
can then run the following to flash OpenWrt and then reboot:
'cd /tmp; curl https://downloads.openwrt.org/...-sysupgrade.bin
--output firmware.bin; mtd -e OS1 -r write firmware.bin OS1'
All targets now use OpenWrt device abstraction. Thus, all targets now
can be built using a per-device RootFS.
Signed-off-by: David Bauer <mail@david-bauer.net>
Upstream removed the factory images for the Archer C20 v1 as they
potentially brick the device. Remove them from Gluon to avoid build
failures on the next OpenWrt 19.07 bump.
Signed-off-by: David Bauer <mail@david-bauer.net>
This device is a dual 5GHz device. It is recommended to manually change the
radio of the first device to the lower 5GHz channels and the second radio
to the upper 5GHz channels
Use a manifest alias for the autoupdater image string of the Netgear
EX3700 / EX3800. This way, no unnecessary symlink is created and the
autoupdater functionality is preserved.
* ar71xx-generic: only create manifest alias for Rocket M5
This follow up the discussion done in #2070 by not creating a symlink
for the Rocket M5. Images for the Rocket M2 can still be flashed on a
Rocket M5.
This change will prevent the Rocket M5 from appearing in Firmware
selectors. Existing devices will still receive updates, as the device
name is still referenced for the device name expected by the M5.
Closes#2070
* docs: remove Rocket M5 from supported devices
Specifications:
* SoC: MT7620A
* RAM: 64 MB DDR
* Flash: 8MB NOR SPI flash
* WiFi: MT7612E (5Ghz) and builtin MT7620A (2.4GHz)
* LAN: 1x100M
The -factory images can be flashed from the device's web
interface or via nmrpflash.
Both devices differ by a additional power outlet for the EX3800.
This patch has been tested on a EX3800 device.
The new options are CONFIG_GLUON_AUTOUPDATER_BRANCH and
CONFIG_GLUON_AUTOUPDATER_ENABLED and allow to control the default branch
and default enable status separately.
The `or ''` fallback in targets/generic is removed, as GLUON_ENV will
set all variables in GLUON_VARS, making previously non-existing
variables exist with an empty value.
The packages necessary to get the DSL modem working increase the
squashfs size by around 1MB.
Remove them from Gluon, as this functionality is not supported.
Normally, we build all nonshared packages (which includes all kernel
modules) to generate an opkg feed for later package installations by
users. On targets without opkg, this just wastes time - disable it.
This change stores a Kernel with Debug-Symbols for the current
architecture in a new output directory '<outputdir>/debug'.
This allows a developer or operator of a network to store the kernel
along with the actual images. In case of a kernel oops the debug
information can be used with the script
'scripts/decode_stacktrace.sh' in the kernel source tree to get the
names to the symbols of the stack trace.
OpenWRT already provides the CONFIG_COLLECT_KERNEL_DEBUG -option that
creates a kernel with debug-symbols in the OpenWRT output directory.
This change enables this option and copies the generated kernel to the
gluon output directory.
Signed-off-by: Chrissi^ <chris@tinyhost.de>
target_config.lua and target_config_check.lua don't pass a table of
callbacks anymore, so target_config_lib.lua can by simplified by moving
all the code that was in the returned function to the toplevel.
So far, we were using a sort operation on the generated .config to
implement precedence of =y packages over =m, and =m over unset.
Unfortunately, this sort not only used for packages, but for all config
lines. This made it impossible to override settings from targets/generic
in a target config when the new setting was sorted before the generic
setting.
To fix this, track configurations by their keys, so we can properly
override config keys that were set before. Value-based precedence is
only preserved for package configuration.
The config() and try_config() calls always take key and value as
separate arguments now. Strings are quoted automatically; the values
true, nil and false map to y, m and unset for tristate options. config()
can take an optional third argument to override the error message to
display when the setting fails to apply.
All existing target configs generate the same .config with the old and the
new code. The new code is also a bit faster on targets with many devices.
In OpenWrt 19.07, the block size was increased to 1024KiB for "tiny"
devices by default to save flash. Unfortunately, this also significantly
increases the cache memory required by squashfs.
In my test, the increased block size reduced the image size by ~64KiB,
but increased the RAM usage by ~2.6MiB. As most tiny devices have only
32MiB of RAM, this is not a reasonable tradeoff.
The ar71xx-generic target already defines an even lower block size of
64KiB.
As x86-generic is compiled to pentium4 (and newer) there is a need for
a subtarget for older devices. The x86-legacy subtarget is set to
compile to pentium (and newer) and should support even very old devics.
x86-legacy includes the packages from x86.inc to only maintain one
package list. The three excludes are because the packages do not exist
for x86-legacy.
The precedence of different package lists was broken since #1876,
disallowing removal of GLUON_FEATURES packages via GLUON_SITE_PACKAGES.
Including all package selections, both implicit defaults and explicit
handling in Gluon, the order of precedence is now the following:
1. OpenWrt defaults (including target-specific defaults)
2. Device-specific packages from OpenWrt
3. Generic default packages (from target/generic)
4. Target default packages (target/$(GLUON_TARGET))
5. Removal of opkg for tiny targets
6. Packages derived from GLUON_FEATURES + GLUON_FEATURES_$(class)
7. GLUON_SITE_PACKAGES
8. GLUON_SITE_PACKAGES_$(class)
9. Device-specific packages from target/$(GLUON_TARGET)
10. Device-specific packages from GLUON_$(device)_SITE_PACKAGES
This also contains various pieces of cleanup:
- No hardcoded order of device classes for target_config.lua arguments
anymore (in fact, the Makefile doesn't know anything about device
classes now)
- target_conifg_lib.lua only hardcodes the fallback class for x86, no
other occurences of specific class names
- Feature -> package list mapping is moved from Makefile to the Lua code
as well (still implemented in Shell though)
This device has broken Ethernet on both ports.
Remove support for those devices. for now, as there was no feedback from
the original author.
Closes#1943
x86-geode does not include the common x86 target-settings. Thus we need
to specify the device class in order to build images with all necessary
packages included.
When adding device classes, targets without devices such as x86 were not
handled. As site and feature packages are included on such a per-device
decision, x86 images ended up without most packages.
Include a class setting for a target and include the class-packages
target-wide when this setting is configured.
Fixes 9c52365077 ("build: introduce device classes")
This commit assigns class-flags to devices. The following scheme is
used:
- ath9k & ath10k: tiny if RAM <128M
- ath10k & ath10k: tiny if RAM <256M
- all: tiny if RAM <64M
- all: tiny if flash <8M
All other devices automatically have the default device-class selected.
