The main difference between the non-EFI and EFI images generated by
OpenWrt is that the former uses an MS-DOS partition table, while the
latter uses GPT. The EFI images still have a BIOS-compatible MBR, so
they work fine on non-EFI systems.
Closes#2403
fixes OOM reboots due too limited ram with ath10k 5Ghz enabled
add some comments to describe the need for ath10k-ct replacement
tested stable on an TP-Link Archer C25v1
more details
694757a08f
AVM Fritz!Box 7520 and Fritz!Box 7530 use the same hardware platform and can
only be distinguished by using the urlader partition or the fritz-tffs tools
and read the ProductID (Fritz_Box_HW247).
Upstream added a standalone SPI kernel-loader which fixes the unbootable
image for the WDR4900. Thus, we can re-introduce this device to Gluon.
Signed-off-by: David Bauer <mail@david-bauer.net>
Specification:
SoC: MediaTek MT7628AN
RAM: 64MiB
Flash: 8MiB
Wifi:
- 2.4GHz: MT7628AN
- 5GHz: MT7612EN
LAN: 1x 10/100 Mbps
Flash instructions:
Flash factory image through stock firmware WEB UI.
Back to stock is possible by using TFTP and stripping down the Firmware
provided by TP-Link to a initramfs.
The flash space between 0x650000 and 0x7f0000
is blank in the stock firmware so I left it out as well.
Note: Buffalo has introduced hardware changes without bumping the
revision number. 19.07 did not support the rb-variant so there's no need
to implement a migration for the rb-variant.
Every g300nh supported by Gluon should either be the s-variant or
been flashed wrongly.
Gone due to
commit 45c84a117b ("ar71xx: drop target")
Gone due to
commit 45c84a1 ("ar71xx: drop target")
Note that it was wrongly marked as device class tiny in
commit 7fd7116e2a ("targets: add device-class flags") in the past,
the device has 64MB RAM and not 32MB.
Also, the device has no "led-running" assigned in DTS. The device has
three LEDs: "green:vpn", "green:lan" and "green:wlan". The first LED,
"green:vpn", has a "V" icon and was used to show the VPN connection
status in the vendor firmware. This LED will be used via the newly
added "led-boot" fallback in gluon-setup-mode. But will be unused
during normal operation due to the unassigned "led-running" in DTS.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Specifications:
* SoC: AR7242 (Virian 400MHz)
* RAM: 64 MB DDR (W9751G6JB-25)
* Flash: 16MB SPI flash (S25FL129PIF)
* WiFi: AR9382 (2.4/5GHz) + 2x SE2595L
* LAN: 1x1000M (PEF7071V)
To install via EVA bootloader, a FTP connection need to be
established to 192.168.178.1 within the first seconds after power on:
ftp> quote USER adam2
ftp> quote PASS adam2
ftp> binary
ftp> debug
ftp> passive
ftp> quote MEDIA FLSH
ftp> put lede-ar71xx-generic-fritz300e-squashfs-sysupgrade.bin mtd1
The Ubiquiti UniFi 6 LR now has a v2 with a different LED setup, thus
the previous model was added a v1 suffix.
Signed-off-by: David Bauer <mail@david-bauer.net>
TP-Link TL-WR902AC v1 is a pocket-size, dual-band (AC750), successor of
TL-MR3020 (both devices use very similar enclosure, in same size). New
device is based on Qualcomm QCA9531 v2 + QCA9887. FCC ID: TE7WR902AC.
Specification:
- 650/391/216 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 1x USB 2.0 (GPIO-controlled power)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz (QCA9531)
- 1T1R 5 GHz (QCA9887)
- 5x LED (GPIO-controlled), 2x button, 1x 3-pos switch
- UART pads on PCB (TP1 -> TX, TP2 -> RX, TP3 -> GND, TP4 -> 3V3, jumper
resitors are missing on TX/RX lines)
- 1x micro USB (for power only)
Flash instructions:
Use "factory" image under vendor GUI.
Recovery instructions:
This device contains tftp recovery mode inside U-Boot. You can use it to
flash OpenWrt (use "factory" image) or vendor firmware.
1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "openwrt-ath79-generic-tplink_tl-wr902ac-v1-squashfs-factory.bin"
to "wr902acv1_un_tp_recovery.bin" and place it in tftp server dir.
3. Connect PC with LAN port, press the reset button, power up the router
and keep button pressed until WPS LED lights up.
4. Router will download file from server, write it to flash and reboot.
MAC Address summary:
- wlan1 (2.4GHz Wi-Fi): Label MAC
- wlan0 (5GHz Wi-Fi): Offset -1 from label
- eth0 (Wired): Offset +1 from label
Root access over serial line in vendor firmware: root/sohoadmin.
Based on support in ar71xx target by: Piotr Dymacz <pepe2k@gmail.com>
