A leading tab character usually marks recipe lines in Makefiles;
non-recipe lines must be indented using spaces.
The incorrect tab character doesn't seen to have caused any issues in
this case, but it should be fixed nonetheless, if only for consistency.
The file_contains_line helper function was not testing whether a file
exists or not prior attempting to read from it.
Add this check to circumvent errors on the private WiFi config in
case the hwflags file is missing.
Reported-by: Tom Herbers <freifunk@tomherbers.de>
Tested-by: Tom Herbers <freifunk@tomherbers.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
d666ebcaa3 ubus: update to the latest version
a9100f2196 base-files: wifi: tidy up the reconf code
b27b63b082 base-files: wifi: swap the order of some ubus calls
6f13a39035 mac80211: print an error if wifi teardown fails
9302e63d1a mac80211: always call wireless_set_data (FS#3784)
bea9380149 mac80211: fix no_reload logic (FS#3902)
ccbe535604 mac80211: backport fix for nl80211 control port tx (fixes FS#3857)
4c29ff7cb8 mac80211: add support for 802.3 encap offload with software rate control
a078037ace mac80211: improve rate control performance
9fa925362f busybox: sysntpd: add trigger to reload server
a75928d125 busybox: sysntpd: option to bind server to iface
Signed-off-by: David Bauer <mail@david-bauer.net>
The relevant entry for the primary MAC location was lost when rebasing
the patch on OpenWrt 21.02.
Fixes commit ded4b8a711 ("rockchip-armv8: add FriendlyARM NanoPi R2S")
Signed-off-by: David Bauer <mail@david-bauer.net>
The OpenWrt routing feed was moved to the OpenWrt GitHub org.
Update the URL, as the old one might not work in the future.
Signed-off-by: David Bauer <mail@david-bauer.net>
Configure a radio for HE (802.11ax) operation in case it's supported by
the hardware. This can be the case for 2.4 GHz as well as 5 GHz.
Signed-off-by: David Bauer <mail@david-bauer.net>
Specifications:
- CPU: MediaTek MT7628AN (580MHz)
- Flash: 16MB
- RAM: 64MB DDR2
- 2.4 GHz: IEEE 802.11b/g/n with Integrated LNA and PA
- Antennas: 4x external single band antennas
- WAN: 1x 10/100M
- LAN: 2x 10/100M
- LEDs: 2x yellow/blue. Programmable (labelled as power on case)
- Non-programmable (shows WAN activity)
- Button: Reset
How to install:
1- Use OpenWRTInvasion to gain telnet and ftp access.
2- Push openwrt firmware to /tmp/ using ftp.
3- Connect to router using telnet. (IP: 192.168.31.1 -
Username: root - No password)
4- Use command "mtd -r write /tmp/firmware.bin OS1" to flash into
the router..
5- It takes around 2 minutes. After that router will restart itself
to OpenWrt.
Specifications:
- SoC: MediaTek MT7621
- Flash: 16 MiB NOR SPI
- RAM: 128 MiB DDR3
- Ethernet: 3x 10/100/1000 Mbps (switched, 2xLAN + WAN)
- WIFI0: MT7603E 2.4GHz 802.11b/g/n
- WIFI1: MT7612E 5GHz 802.11ac
- Antennas: 4x external (2 per radio), non-detachable
- LEDs: Programmable "power" LED (two-coloured, yellow/blue)
Non-programmable "internet" LED (shows WAN activity)
- Buttons: Reset
Installation:
Bootloader won't accept any serial input unless "boot_wait" u-boot
environment variable is changed to "on".
Vendor firmware won't accept any serial input until "uart_en" is
set to "1".
Using the https://github.com/acecilia/OpenWRTInvasion exploit you
can gain access to shell to enable these options:
To enable uart keyboard actions - 'nvram set uart_en=1'
To make uboot delay boot work - 'nvram set boot_wait=on'
Set boot delay to 5 - 'nvram set bootdelay=5'
Then run 'nvram commit' to make the changes permanent.
Once in the shell (following the OpenWRTInvasion instructions) you
can then run the following to flash OpenWrt and then reboot:
'cd /tmp; curl https://downloads.openwrt.org/...-sysupgrade.bin
--output firmware.bin; mtd -e OS1 -r write firmware.bin OS1'
e16a45f258 iwinfo: update to latest Git HEAD
0c51b265bf iwinfo: update to latest Git HEAD
85cef1cf22 kernel: bump 5.4 to 5.4.128
e171d11f55 libusb: Fix parsing of descriptors for multi-configuration devices
3d62b5d5c6 base-files: fix /tmp/TZ when zoneinfo not installed
3047df2317 base-files: fix zoneinfo support
ab5010d170 exfat: update to 5.12.3
72d93c1ba4 realtek: Fix failsafe mode
7a5a247c1f base-files: failsafe: Remove the VLAN modifier from interface name
c0fdfd15fc base-files: failsafe: Fix IP configuration
98b1a6435f kernel: Backport patch to automatically bring up DSA master when opening user port
ec780bdb92 kernel-5.4: backport latest patches for wireguard
82c700de67 hostapd: fix handling of the channel utilization options
1247a6bb35 bcm4908: fix Ethernet broken state after interface restart
25daa921da bcm4908: add kmod-gpio-button-hotplug
74dbf3412b base-files: fix typo in config_generate MAC check
125deb4d78 base-files: set MAC for bridge ports (devices) instead of bridge itself
e410ef8389 hostapd: wolfssl: add RNG to EC key
f6d8c0cf2b wolfssl: always export wc_ecc_set_rng
56228e9393 ath79: don't autodetect AR8033 PHY capabilities
2e157714a8 build,json: fix generation with empty profiles
8add3e139c build: preserve profiles.json between builds
All targets now use OpenWrt device abstraction. Thus, all targets now
can be built using a per-device RootFS.
Signed-off-by: David Bauer <mail@david-bauer.net>
