61b7085ff7
2 Commits
| Author | SHA1 | Message | Date | |
|---|---|---|---|---|
David Bauer
|
70ed8ea18b |
modules: update openwrt
5b7d01b427 iwinfo: update to latest HEAD 39aaec62ca hostapd: refresh patches e2030fcfa7 hostapd: add ubus link-measurements notifications 1a2940f68e hostapd: add ubus method for requesting link measurements b4a9597154 hostapd: add support for enabling link measurements 5a18028c69 iwinfo: update to latest HEAD b519d76276 iwinfo: update to latest Git head 01cc5e195d iwinfo: update to latest Git HEAD 44781b265c iwinfo: update to the latest version f7c445aa7d iwinfo: update to the latest version 75cbd8de00 wolfssl: fix compilation with /dev/crypto 1418439da9 kernel: add missing config symbols 39f1815b3e mac80211: fix QCA9561 PA bias 1769e3162e ramips: mt7620: disable SOC VLANs for external switches 30e47fb1e4 ramips: mt7620: ethernet: use more macros and bump version 3f976d0225 ramips: mt7620: fix RGMII TXID PHY mode 6685eb29e5 ramips: mt7620: add ephy-disable option to switch driver 47db830b82 ramips: mt7620: move mt7620_mdio_mode() to ethernet driver 6876465875 ramips: mt7620: use DTS to set PHY base address for external PHYs 5d7805c78b ramips: mt7620: allow both internal and external PHYs 01bbed7444 ramips: mt7620: fix ethernet driver GMAC port init 6491212ea7 ramips: mt7620: remove useless GMAC nodes a14c2d409c ramips: mt7620: simplify DTS properties for GMAC c652a06eef ramips: mt7620: enable autonegotiation for all ports 08ec622c46 ramips: make PHY initialization more descriptive 4123f177f9 ramips: add support for the Wavlink WL-WN579X3 92af15077f ramips: split Youku YK1 to YK-L1 and YK-L1c 55f8eb84d2 ramips: improve pinctrl for Youku YK-L1 92489b4f82 ramips: speed up spi frequency for Youku YK-L1 bea1891182 ramips: remove obsolete mx25l25635f compatible hack 6c44b157e5 mvebu: kernel: enable CONFIG_BLK_DEV_NVME f0f9b7ac5c OpenWrt v21.02.3: revert to branch defaults 42a15ca378 OpenWrt v21.02.3: adjust config defaults 1d4dea6d4f ath79: Move TPLink WPA8630Pv2 to ath79-tiny target 41a97c2074 bcm27xx: add AMP2 to HifiBerry DAC+ / DAC+ Pro package 9a765554f4 ath79: add support for MikroTik RouterBOARD mAP lite 2cc9ee8000 ath79: add support for Yuncore A930 06874171d1 ath79: add support for Yuncore XD3200 c5ef62a218 wolfssl: bump to 5.2.0 99b00edf35 mac80211: Update to version 5.10.110-1 9132344444 bpftools: fix feature override for masking clang 169c9e3a88 ramips: fix reboot for remaining 32 MB boards 39bf2aee0e kernel: bump 5.4 to 5.4.188 3008f1f441 imagebuilder: fix broken image generation with external targets |
||
Sven Eckelmann
|
6e35f6b95a |
ath79-generic: Add support for OpenMesh OM5P-AC v1
Device specifications:
======================
* Qualcomm/Atheros QCA9558 ver 1 rev 0
* 720/600/240 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2T2R 2.4 GHz Wi-Fi (11n)
* 2T2R 5 GHz Wi-Fi (11ac)
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* external h/w watchdog (enabled by default))
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* TI tmp423 (package kmod-hwmon-tmp421) for temperature monitoring
* 2x ethernet
- eth0
+ AR8035 ethernet PHY (RGMII)
+ 10/100/1000 Mbps Ethernet
+ 802.3af POE
+ used as LAN interface
- eth1
+ AR8035 ethernet PHY (SGMII)
+ 10/100/1000 Mbps Ethernet
+ 18-24V passive POE (mode B)
+ used as WAN interface
* 12-24V 1A DC
* internal antennas
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to the
device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Gluon image name change
=======================
The device had the image name "openmesh-om5p-ac" in older versions of Gluon.
This had to be changed with the new name in the device trees of the ath79
device tree.
|