ath10k has to switch the regulatory domain when switching the default
country when ATH_USER_REGD is enabled. This is for example important when
switching from country US (FCC) to DE (ETSI). The ath implementation will
use ath_reg_dyn_country_user_allow to check if this is allowed.
Unfortunately, this function always seems to return false to
ath_reg_notifier_apply even when ATH_USER_REGD is enabled. But it must
actually always accept the requests from the user (when ATH_USER_REGD is
enabled) to correctly set the conformance test limits in the ath10k binary
blob.
Not doing it will sometimes allow too high transmit powers on edge channels
for correctly calibrated devices outside their default regulatory domain.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
The assignment of the gpio_count and reg_base in ath79_gpio_output_select
takes care that only supported platforms can use ath79_gpio_output_select.
But the rebase of the patches after the last OpenWrt base update
accidentally added an extra check for the SoC which was missing support
soc_is_qca955x().
Boots on QCA955X devices which were using ath79_gpio_output_select stopped
with
Kernel bug detected[#1]:
[...]
Call Trace:
[<803e6174>] ath79_gpio_output_select+0x30/0xe8
[<803ed590>] om5p_acv2_setup+0x24/0x200
[<803e4dc0>] ath79_setup+0x28/0x38
[<80069ac8>] do_one_initcall+0x148/0x1ec
[<803e2cc4>] kernel_init_freeable+0x150/0x208
[<80065218>] kernel_init+0x10/0x114
[<80060878>] ret_from_kernel_thread+0x14/0x1c
Fixes: a22c1d5670 ("Update OpenWrt base")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Some (possibly broken) bootloaders incorrectly initialize the at8033 phy.
This breaks auto-negotation on these SGMII devices. The mode has therefore
to be set back in to a valid configuration by Linux.
Fixes#911
Using HTTPS breaks the download on Debian Wheezy. The switch was an
unintended side effect of the backport from LEDE.
Also, fix the commit message of the backport patch (mwlwifi is not updated
anymore since the last OpenWrt base upgrade).
Fixes#919
Generate flashable images for the Archer C7 v2 with current stock firmware
again.
To set the region code, the GLUON_REGION variable must be set to "us" or
"eu" in site.mk or as a make argument.
Fixes#860
This patchset enables the RX LNA for the CPE210/510, improving RX by about
20dB. The profiles for CPE210 and CPE510 is split into two images.
The problematic patch switching the CPE510 to the secondary ART is left
out.
The new MR1750v2 device support is only available in LEDE master. The
relevant patches have to backported to add support for them in Gluon
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
The new OM2P-HSv3 device support is only available in LEDE master. The
relevant patches have to backported to add support for them in Gluon
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
This patchset enables the RX LNA for the CPE210/510, improving RX by about
20dB. The profiles for CPE210 and CPE510 is split into two images, so the
CPE510 can use the correct ART offset, improving the TX power by 10dB.
Fixes#796
Most doubles that are delivered via respondd have limited input
precision, but are converted with up to 17 digits of precision. That can
cause ugly blowups like 0.2800000000000001 in the output, which is
avoided by specifying better format strings (like "%.2f" in most cases).
The new ath9k/ath10k based devices are only available in OpenWrt trunk. The
relevant patches have to backported to add support for them in Gluon
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
The workaround to generate sysupgrade images for OpenMesh devices in gluon
is replaced in LEDE/OpenWrt by a special patch. It is therefore better to
drop the workaround and use the upstream version.
Reported-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Original commit message:
MIPS: ath79: make bootconsole wait for both THRE and TEMT
This makes the ath79 bootconsole behave the same way as the generic 8250
bootconsole.
Also waiting for TEMT (transmit buffer is empty) instead of just THRE
(transmit buffer is not full) ensures that all characters have been
transmitted before the real serial driver starts reconfiguring the serial
controller (which would sometimes result in garbage being transmitted.)
This change does not cause a visible performance loss.
In addition, this seems to fix a hang observed in certain configurations on
many AR7xxx/AR9xxx SoCs during autoconfig of the real serial driver.
A more complete follow-up patch will disable 8250 autoconfig for ath79
altogether (the serial controller is detected as a 16550A, which is not
fully compatible with the ath79 serial, and the autoconfig may lead to
undefined behavior on ath79.)
Patch tested on v2016.1.x branch with Freifunk Magdeburg firmware on
Debian Jessie amd64 Xen host. See the same patch in our gluon fork here:
https://github.com/FreifunkMD/gluon/blob/fix-sysupgrade-xen/patches/openwrt/0058-x86-fix-platform_export_bootpart-for-Xen-virtual-disks.patch
Sysupgrade was tested successfully by manually making the change before
upgrading in the filesystem of the running node and upgrading to the
fixed FFMD experimental build in config mode via expert settings in
webgui.
Patch also submitted to OpenWRT trunk already.
Signed-off-by: Alexander Dahl <alex@netz39.de>
The trunk version of mac80211 doesn't need these dependencies anymore as
they are compiled into the kernel.
While this didn't cause any issues for Gluon as we always build the kernel
with all modules, this fix makes the patch work on a plain OpenWrt CC as
well.
ath9k expects to get revision id 2 for the QCA9531 ver. 2 rev. 0. This
fixes the very low TX power on some devices like the TP-LINK
TL-WR841ND v10.
As ath79_soc_rev is only used to get the revision number to ath9k on the
QCA9533, just set it to the expected value on the ver. 2.
This patch adds the kernel modules to for the very common Realtek RTL8150 and Realtek 8152 based USB-to-Ethernet converters.
After this patch the following packages can be added to targets (or site.mk):
kmod-usb-net-rtl8150
kmod-usb-net-rtl8152
The modules are already available in openwrt trunk, but not in Chaos Calmer. This patch is just a temporary backport.
The modules are needed for Futros with additional USB-Ethernet-Interface and VMs with dedicated USB-NIC
We can't use the same image for these two devices, so as a workaround,
remove ZR-600DHP from the name for now, so the autoupdater can work and
users aren't confused.
hostapd would switch the primary and secondary channel on 5GHz networks in
certain circumstances, completely breaking the adhoc interfaces of the WLAN
adapter (they would lose their configuration).
As a temporary fix, disable this channel switch function.
