The new MR1750v2 device support is only available in LEDE master. The
relevant patches have to backported to add support for them in Gluon
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
The new OM2P-HSv3 device support is only available in LEDE master. The
relevant patches have to backported to add support for them in Gluon
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
This patchset enables the RX LNA for the CPE210/510, improving RX by about
20dB. The profiles for CPE210 and CPE510 is split into two images, so the
CPE510 can use the correct ART offset, improving the TX power by 10dB.
Fixes#796
Most doubles that are delivered via respondd have limited input
precision, but are converted with up to 17 digits of precision. That can
cause ugly blowups like 0.2800000000000001 in the output, which is
avoided by specifying better format strings (like "%.2f" in most cases).
The OpenMesh devices have a sticker with the eth0 mac address on the
bottom. Also all other mac addresses are calculated based on this address.
Therefore, it is better to use this as primary mac address instead of the
WiFi mac address.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
The returned name for OpenMesh devices with a an extra vX when calling
lua -e 'print(require("platform_info").get_image_name())'
doesn't contain a dash between the vX and the device name. Thus the image
should also not contain a dash.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
The new ath9k/ath10k based devices are only available in OpenWrt trunk. The
relevant patches have to backported to add support for them in Gluon
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
This patch adds a new gluon-ebtables package to filter IGMP/MLD messages
via ebtables.
For one thing this reduces multicast overhead: About one third of all
ICMPv6 multicast traffic in Lübeck or Hamburg is MLD.
Furthermore it removes a potential Distributed Denial-of-Service vector
(see Gluon ticket #553).
Finally, it is a prerequisite for enabling bridge multicast snooping in
a decentral and robust fashion.
Note that IGMP/MLD are filtered for multicast traffic coming from
the mesh, too (new MULTICAST_IN), as unfortunately there seem to
be other queriers somewhere in the mesh at least for Freifunk
Lübeck. Also adding these rules to be prepared to anyone intentionally
or unintentionally disabling these filters on his/her node.
Node operators not running Gluon (for instance gateway nodes) should
make sure to either enable multicast_router towards bat0 or disable
multicast snooping entirely if they have a bridge on top of bat0.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
ebtables actually skips any IPv6 extension headers like the hop-by-hop
one. So this rule is actually void.
The intend back then was to allow passing MLD messages into the mesh.
Since extension headers are skipped, the general icmpv6 rule will
actually match MLD messages. So the hop-by-hop rule is unnecessary,
too.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
The workaround to generate sysupgrade images for OpenMesh devices in gluon
is replaced in LEDE/OpenWrt by a special patch. It is therefore better to
drop the workaround and use the upstream version.
Reported-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Don't fork reboot process before all package hooks have been handled and
rendering is complete.
Replace debug.setfenv hack to close stdout with nixio.dup.
Fixes#772
The image validation currently fails on some devices (tested OpenMesh)
because it isn't done via sysupgrade. But the checks depend partially on
the integration in sysupgrade (e.g. via loops that can be stopped via
"break statements").
Instead of hacking its own version check, it is easier and better tested to
just use 'sysupgrade -T' like it is already done by LuCI.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Lua's tables are 1-based, so we must decrement the index by 1 to get the
desired MAC addresses. By not doing this, the second IBSS interface would
get the address with index 8, but only indices 0..7 are available.
Fixes: c73a12e0ea
