Speedy join only works when the received packet is either broadcast or an
4addr unicast packet. Thus packets converted from broadcast to unicast via
the gateway handling code have to be converted to 4addr packets to allow
the receiving gateway server to add the sender address as temporary entry
to the translation table.
Not doing it will make the batman-adv gateway server drop the DHCP response
in many situations because it doesn't yet have the TT entry for the
destination of the DHCP response.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The new MR1750v2 device support is only available in LEDE master. The
relevant patches have to backported to add support for them in Gluon
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
The new OM2P-HSv3 device support is only available in LEDE master. The
relevant patches have to backported to add support for them in Gluon
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
This patchset enables the RX LNA for the CPE210/510, improving RX by about
20dB. The profiles for CPE210 and CPE510 is split into two images, so the
CPE510 can use the correct ART offset, improving the TX power by 10dB.
Fixes#796
Most doubles that are delivered via respondd have limited input
precision, but are converted with up to 17 digits of precision. That can
cause ugly blowups like 0.2800000000000001 in the output, which is
avoided by specifying better format strings (like "%.2f" in most cases).
The OpenMesh devices have a sticker with the eth0 mac address on the
bottom. Also all other mac addresses are calculated based on this address.
Therefore, it is better to use this as primary mac address instead of the
WiFi mac address.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
The returned name for OpenMesh devices with a an extra vX when calling
lua -e 'print(require("platform_info").get_image_name())'
doesn't contain a dash between the vX and the device name. Thus the image
should also not contain a dash.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
The new ath9k/ath10k based devices are only available in OpenWrt trunk. The
relevant patches have to backported to add support for them in Gluon
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
This patch adds a new gluon-ebtables package to filter IGMP/MLD messages
via ebtables.
For one thing this reduces multicast overhead: About one third of all
ICMPv6 multicast traffic in Lübeck or Hamburg is MLD.
Furthermore it removes a potential Distributed Denial-of-Service vector
(see Gluon ticket #553).
Finally, it is a prerequisite for enabling bridge multicast snooping in
a decentral and robust fashion.
Note that IGMP/MLD are filtered for multicast traffic coming from
the mesh, too (new MULTICAST_IN), as unfortunately there seem to
be other queriers somewhere in the mesh at least for Freifunk
Lübeck. Also adding these rules to be prepared to anyone intentionally
or unintentionally disabling these filters on his/her node.
Node operators not running Gluon (for instance gateway nodes) should
make sure to either enable multicast_router towards bat0 or disable
multicast snooping entirely if they have a bridge on top of bat0.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
ebtables actually skips any IPv6 extension headers like the hop-by-hop
one. So this rule is actually void.
The intend back then was to allow passing MLD messages into the mesh.
Since extension headers are skipped, the general icmpv6 rule will
actually match MLD messages. So the hop-by-hop rule is unnecessary,
too.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
The workaround to generate sysupgrade images for OpenMesh devices in gluon
is replaced in LEDE/OpenWrt by a special patch. It is therefore better to
drop the workaround and use the upstream version.
Reported-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
