This reverts commit 9b1eb40fe7.
With the batman-adv v2019.2 upgrade reverted (c1a7733956), the batman-adv
multicast-to-multi-unicast feature is not available yet. Without that it is
going to be very unlikely of the batman-adv multicast optimizations to
take effect. E.g. some outdated nodes would disable it.
To avoid confusion and diversion with a few communities having it enabled
and most implicitly deactivated, just deactivate it for all for now
until batman-adv is updated to v2019.2 or greater again.
mac_to_ip() calculates an ipv6 address from a mac address according to
RFC 4291. For wireguard we have to use specially crafted addresses that
must be unique. This allows calculating such unique mac-based addresses
by allowing to optionally specifying the bytes to be inserted into the
address.
The new routing_algo site.conf value BATMAN_IV_LEGACY is introduced. With
these changes, the routing_algo setting becomes mandatory.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
We cannot add the same file (here: /lib/gluon/mesh-batman-adv/compat) to
two, installed packages. Therefore, instead of determining the compat
version number from this file, infer it from the batman-adv release
version number instead.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
This is a fix for the broken ingress traffic-shaping in gluon v2018.2.2
and possibly earlier.
For ingress traffic shaping the kernel option NET_ACT_POLICE is needed.
Before this patch there was no dependency to this. Neither in
gluon_core, gluon-mesh-vpn-core nor in the package.
This patch adds this dependency.
[Matthias Schiffer: move dependency from GLUON_CORE to gluon-mesh-vpn-core]
Fixes#1790
package/gluon-web-network/luasrc/lib/gluon/config-mode/model/admin/network.lua:122:16: (W431) shadowing upvalue f on line 19
Fixes: bab4af01e ("gluon-web-network: improve PoE GPIO name translation
handling")
The gluon-authorized-keys is usually installed to use SSH keys to
authenticate a user against the device. To make this useful, it is also
required to disable passwordless SSH access to the device.
This new dependency is only required when the user doesn't have
gluon-setup-mode enabled already.
Fixes: #1777
Reported-by: yanosz <github@yanosz.net>
Fixes: a753fa79e3 ("gluon-authorized-keys: add keys from site.conf")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
This MR includs only the VPN MODE of the hoodselector whitch simply set
hoods base on their geopositions.
Signed-off-by: Jan-Tarek Butt <tarek@ring0.de>
check_site.lua: fix language syntax
muss -> must
rage -> range
at lease -> at least
coordiantes -> coordinates
realaise -> realised
gluon-hoodselector: fix language syntax in hoodselector
can not -> can't
routers -> router's
continure -> continue
to next -> to the next
TMP -> temporary
for current -> for the current
continure -> continue
with next -> with the next
thier -> there
provides -> provide
possition -> position
therfore -> therefore
gluon-hoodselector: fix language syntax in util.lua
realaise -> realised
gluon-hoodselector: fix language syntax and use autoupdate lock mechanism.
gluon-hoodselector: fix spelling/grammar
gluon-hoodselector: automatically set SECTION and CATEGORY for Gluon packages
gluon-hoodselector-add-VPN-MODE: add micrond & libjson-c dependency
gluon-hoodselector-add-VPN-MODE: check running hoodselector before loading lua
gluon-hoodselector-add-VPN-MODE: remove nixio dependency from hoodselector util
Revert "gluon-hoodselector-add-VPN-MODE: check running hoodselector before loading lua"
This reverts commit 535b0a1b2fb73e563bf6a44b568a796440bd307f.
add luaposix and luabitop to pakage dependency
sbin/hoodselector: remove nixio requiemend
sbin/hoodselector: load hoods only if necessary
gluon-hoodselector: use VPN abstraction layer. the hoodselectore does
not need to know about all individual VPN protocols.
gluon-hoodselector: Makefile add gluon-mesh-vpn-core as dependency
gluon-hoodselector: apply changes of mesh vpn lib
gluon-hoodselector: remove outdated comments
package/gluon-hoodselector: check_site.lua rm domain seed check thus its already checked by gluon-core
package/gluon-hoodselector: util.lua code cleanup and refactoring
package/gluon-hoodselector: hoodselector code cleanup and refactoring
gluon-hoodselector: util.lua, use taps instead of spaces. Use posix.unistd.access instead of io.open
Signed-off-by: Jan-Tarek Butt <tarek@ring0.de>
gluon-hoodselector: hoodselector, use taps instead of spaces.
Signed-off-by: Jan-Tarek Butt <tarek@ring0.de>
gluon-hoodselector: check_site.lua: replace hood with domain
Signed-off-by: Jan-Tarek Butt <tarek@ring0.de>
gluon-hoodselector: drop VPN mode and rename hood to domain. Furthermore implement geolocator mode as neorayder way
Signed-off-by: Jan-Tarek Butt <tarek@ring0.de>
package/gluon-hoodselector: rm duplicated print output
Signed-off-by: Jan-Tarek Butt <tarek@ring0.de>
package/gluon-hoodselector util: fix wrong function signature
Signed-off-by: Jan-Tarek Butt <tarek@ring0.de>
small typo fixes
small typo fixes
Update util.lua
processes are really restarted now. new (old) problem: nodes will not forget their former ipv6-addresses. watchdog could here with that.
gluon-hoodselector util.lua: replace i iterator with _
Signed-off-by: Jan-Tarek Butt <tarek@ring0.de>
Update util.lua
now polygons with holes are recognized correctly. also a mix of nested polygons and boxes should be possible as shapes[]
package/gluon-hoodselector: hoodselector use gluon-reload for daemon restarts/reloads
Signed-off-by: Jan-Tarek Butt <tarek@ring0.de>
package/gluon-hoodselector: util.lua use math-polygon lib and rm restart_services function. Rectengles will be converted into polygons now
Signed-off-by: Jan-Tarek Butt <tarek@ring0.de>
package/gluon-hoodselector: Makefile rewrite description update depends list
Signed-off-by: Jan-Tarek Butt <tarek@ring0.de>
package/gluon-hoodselector: check_site.lua reduce complexity
Signed-off-by: Jan-Tarek Butt <tarek@ring0.de>
package/gluon-hoodselector: use : for gluon_version Val
Signed-off-by: Jan-Tarek Butt <tarek@ring0.de>
package/gluon-hoodselector: fix if equal syntax
Signed-off-by: Jan-Tarek Butt <tarek@ring0.de>
luasrc/usr/lib/lua/hoodselector/util.lua: check_site.lua simplify checksite script and fix if logic
Signed-off-by: Jan-Tarek Butt <tarek@ring0.de>
package/gluon-hoodselector: set space after comma, rm unnecessary error handling
Signed-off-by: Jan-Tarek Butt <tarek@ring0.de>
package/gluon-hoodselector: use only brackes on require function no mixup
Signed-off-by: Jan-Tarek Butt <tarek@ring0.de>
package/gluon-hoodselector: check_site.lua rm unuse variables and fix non std global function
Signed-off-by: Jan-Tarek Butt <tarek@ring0.de>
package/gluon-hoodselector: util.lua rm unuse include
Signed-off-by: Jan-Tarek Butt <tarek@ring0.de>
package/gluon-hoodselector: rm comment return nil in function get_geolocation()
Signed-off-by: Jan-Tarek Butt <tarek@ring0.de>
package/gluon-hoodselector: Makefile refactor pkg description
Signed-off-by: Jan-Tarek Butt <tarek@ring0.de>
We now keep the VPN enable state, bandwidth limit enable and actual limits
in the core config to avoid having to recover "user intent" from different
config files when the used VPN packages change.
Fixes#1736
Several fixes and enhancements related to multicast were added upstream
in batman-adv. So let's give the batman-adv multicast optimizations
another go.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
The is_outdoor function is placed inside the gluon.platform module, not
the platform_info module. Currently, the outdoor-mode wizard component
and the upgrade script fail due to nil-value calls.
adds a section to the wizard for outdoor capable devices
that informs the user of of the regulatory situation and
allows a quick toggle of the outdoor mode.
Add the `wifi5.outdoor_chanlist` site configuration that
allows specifying an outdoor channel range that can be
switched to for regulatory compliance.
Upon enabling the outdoor option the device will
- configure the `outdoor_chanlist` on all 5 GHz radios
- which may enable DFS/TPC, based on the regulatory domain
- disable ibss/mesh on the 5 GHz radio, as DFS *will*
break mesh connections
- allow for htmode reconfiguration on 5 GHz radios
The outdoor option can be toggled from
- Advanced Settings
- W-LAN
- Outdoor Installation
The `preserve_channel` flag overrules the outdoor channel
selection.
The batctl v2013.4 build was removed from the batman-adv-legacy package
as the current, upstream batctl releases work with batman-adv-legacy,
too.
As a replacement we need to add the upstream batctl dependency to
gluon-mesh-batman-adv-14 to have a batctl available again here.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
The commit a080049735 ("gluon-status-page-mesh-batman-adv: Retrieve TQ of
neighbors with non-best direct link") removed the check whether a neighbor
has the BATADV_ATTR_FLAG_BEST set. But consumers may still want to filter
out or mark neighbors which don't have this flag set. To assist with such a
feature, enhance the neighbor object with an extra boolean "best" attribute
which stores whether the BATADV_ATTR_FLAG_BEST was found or not.
Reported-by: Vincent Wiemann <webmaster@codefetch.de>
The commit ee63ed42fe ("gluon-mesh-batman-adv: List neighbors with
non-best direct link") removed the check whether a neighbor has the
BATADV_ATTR_FLAG_BEST set. But consumers may still want to filter out or
mark neighbors which don't have this flag set. To assist with such a
feature, enhance the neighbor object with an extra boolean "best" attribute
which stores whether the BATADV_ATTR_FLAG_BEST was found or not.
Reported-by: Vincent Wiemann <webmaster@codefetch.de>
Links between two direct neighbors are not always the best route between
these devices. The flag BATADV_ATTR_FLAG_BEST would not be set for these
originator entries and the respondd module would just ignore this entry.
If these neighbors are not accepted and returned to the status page then
some of the neighbor entries will show a name, (acceptable) signal strength
and mac address but no TQ value.
Fixes: 28668c8c52 ("gluon-status-page: API")
Links between two direct neighbors are not always the best route between
these devices. The flag BATADV_ATTR_FLAG_BEST would not be set for these
originator entries and the respondd module would just ignore this entry.
This causes missing links in meshviewer and similar tools. And when the
link quality is nearly equal and but fluctuates slightly, these links will
from time to time appear and disappear on the map.
Fixes: 2e0e24a992 ("announce neighbours using alfred/gluon-announce")
The device is broken until the next release. The LEDs are currently not
working (fixed in current OpenWRT master).
Also give a brief explanation about the BROKEN status being dependent on
the WiFi chip used and not the SoC family in general.
When two domains alias the same name (or one aliases another), display a
meaningful error message like:
Failed to alias domain 'foo' as 'bar', name already taken by
domain 'baz'.
The amount of local wifi clients is currently counted by two different
ways:
* asking the kernel wifi layer for the number of of clients on 2.4GHz and
5GHz band
* asking batman-adv for the number of non-timed out entries in the local
translation table with WiFi flag
The number of wifi24+wifi5 and the number of TT wifi client counts are
reported via respondd to various consumers. The ffrgb meshviewer is
displaying these values as:
* 2,4 GHz: wifi24
* 5 GHz: wifi5
* other: (TT local wifi+non-wifi clients) - (wifi24 + wifi5)
But the local translation table is holding entries much longer than the
wifi layer. It can therefore easily happen that a wifi client disappears in
the kernel wifi layer and batman-adv still has the entry stored in the
local TT.
The ffrgb meshviewer would then show this count in the category "other".
This often results in confusions because "other" is usually for ethernet
clients. And nodes with a frequently disappearing larger group of clients
(near bus stations or larger intersections) often show most clients under
the group "other" even when this devices doesn't have a LAN ethernet port.
It is better for presentation to calculate the number of total wifi clients
by summing up wifi24 + wifi5. And getting the number of total clients (non
wifi + wifi) by adding the result of the previous calculation to the sum of
non-wifi client in the local batman-adv translation table.
Fixes: 89a9d8138c ("gluon-mesh-batman-adv-core: Announce client count by frequency")
Reported-by: Pascal Wettin <p.wettin@gmx.de>
Gluon has multiple ways to obtain unique MAC-addresses. They are either
provided by the WiFi driver or derived from the primary MAC-address.
Quoting the same file:
> It's necessary that the first 45 bits of the MAC address don't
> vary on a single hardware interface, since some chips are using
> a hardware MAC filter. (e.g 'rt305x')
This currently fails in case the rt35xx based chips mac address differs
from the primary MAC. In this case, the MAC address for the client0 radio
(vif 1) comes from the WiFi driver. As there is only a single
MAC-address provided by '/sys/class/ieee80211/phyX/addresses' but the
MAC-address for mesh 0 (vif 2) is derived from the Node-ID, resulting in
different first 45 bits. The WiFi won't come up altogether in this case.
This commit verifies at least 4 MAC-Addresses are provided by the WiFi
driver. If this is not the case, all MAC-addresses are derived from the
primary MAC. This way, affected radios are working correctly.
This commit distributes dualband radios evenly on 2.4 GHz and 5GHz with
2.4 GHz being prioritised higher than 5 GHz. This means in case a device
has only a single radio and this radio supports operation in both bands,
it will be set to 2.4 GHz.
Tested-by: Martin Weinelt <martin@darmstadt.freifunk.net>
Signed-off-by: David Bauer <mail@david-bauer.net>
Allow odhcp6c to fork the script to handle router
advertisments in 30 seconds intervals. This is the value
that was previously used in Gluon v2018.1 / LEDE 17.01.
The default value is 3 seconds and while it is RFC compliant
it can put alot of pressure on even moderately sized devices.
Signed-off-by: Martin Weinelt <martin@darmstadt.freifunk.net>
log-file /dev/stderr is broken for babeld as it eats log messages for debug log.
This commit gets rid of the option. This allows -d N to be used as babeld command
line option.
This patch makes use of the new feature in l3roamd to gracefully
add, remove and list the mesh interfaces that are currently in use. This
helps when changing mesh interfaces often - a characteristic of the
wireguard protocol implementation as in the previous behavior all local
clients are dropped when adjusting mesh interfaces.
gluon-wan is a sudo-like exec wrapper that switches the process group to
gluon-mesh-vpn, making it use the WAN dnsmasq rather than resolving over
the mesh.
Note that this only affects DNS at the moment. Processes running under
gluon-wan will still use the regular mesh IPv6 routing table, and not the
WAN routing table. This is not a problem for IPv4, as there is only one
IPv4 routing table.
Fixes#1575
