Commit Graph

487 Commits

Author SHA1 Message Date
J. Burfeind
1f4c5681e4
ath79-generic: add support for CPE710v1 (#2558) 2022-06-17 23:12:36 +02:00
J. Burfeind
1ab1df080e
ath79-generic: (re)add support for NanoStation Loco M2 (XW) (#2547)
Gone due to
commit 45c84a117b ("ar71xx: drop target")
2022-06-16 14:52:05 +02:00
lemoer
707f81926f docs/user: move mtu to mtu.rst 2022-06-07 18:30:54 +02:00
lemoer
2daf13cd4a docs: add docs for gluon-mesh-vpn-wireguard 2022-06-07 18:30:54 +02:00
Matthias Schiffer
0b9d3b78c4
ath79-generic: update Archer C6 v2 image name (#2534)
The DTS model name has been changed to "TP-Link Archer C6 v2 (EU/RU/JP)"
to distinguish it from the US version.

Closes #2533
2022-06-01 01:06:06 +02:00
J. Burfeind
2887adef5f
ath79-generic: (re)add support for NanoBeam M5 (XW) (#2432)
Gone due to
commit 071cf7b20f ("Switch to Lua for target definitions")

Has prior been introduced as untested -> broken in
commit d586720c5c ("ar71xx-generic: add support for Ubiquiti NanoBeam M5")

Was commented out in the former commit.
2022-05-30 20:44:43 +02:00
David Bauer
7c7fbd14b7
Merge pull request #2524 from s-2/dir-825
ath79-generic: migrate D-Link DIR-825 B1 from ar71xx
2022-05-29 17:31:22 +02:00
Jan
b690939fae
ramips-mt7620: remove "broken" status for ASUS RT-AC51U (#2494) 2022-05-27 21:40:05 +02:00
Sebastian Schaper
d56a0f2602 ath79-generic: migrate D-Link DIR-825 B1 from ar71xx
Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
2022-05-27 19:28:04 +02:00
Matthias Schiffer
674ec7b64a
ath79-generic: re-add support for Ubiquiti UniFi AP Outdoor+ (#2440)
Removed in 45c84a117b ("ar71xx: drop target").
2022-05-26 23:35:18 +02:00
Maciej Krüger
a0df96eb97
ath79-mikrotik: add support for Mikrotik RB951Ui-2nD (#2377)
Re-add mikrotik target

Note that previous images were generic ones and as such no migration
path is provided other than manually flashing the image via config-mode.
2022-05-22 11:45:28 +02:00
David Bauer
1ef3edbe58
Merge pull request #2352 from lemoer/pr_site_vpn_mtu_in_provider
RFC: gluon-mesh-vpn-*: make MTU of VPN device provider specific
2022-05-22 11:45:10 +02:00
lemoer
d3dbc3d8ed docs: move mtu in site.rst 2022-05-21 20:09:01 +02:00
Martin Weinelt
99bdce1072
ramips-mt7621: add TP-Link RE650v1 (#2527)
- [x] Must be flashable from vendor firmware
  - [x] Web interface
  - [ ] TFTP (untested, but possible according to OpenWrt wiki)
  - [ ] Other: <specify>
- [x] Must support upgrade mechanism
  - [x] Must have working sysupgrade
    - [x] Must keep/forget configuration (`sysupgrade [-n]`, `firstboot`)
  - [x] Gluon profile name matches autoupdater image name
        (`lua -e 'print(require("platform_info").get_image_name())'`)
- [x] Reset/WPS/... button must return device into config mode
- [x] Primary MAC address should match address on device label (or packaging)
      (https://gluon.readthedocs.io/en/latest/dev/hardware.html#notes)
  - When re-adding a device that was supported by an earlier version of Gluon, a
    factory reset must be performed before checking the primary MAC address, as
    the setting from the old version is not reset otherwise.
- Wired network
  - [x] should support all network ports on the device
  - [x] must have correct port assignment (WAN/LAN)
    - On devices supplied via PoE, there is usually no explicit WAN/LAN labeling on the hardware.
      The PoE input should be the WAN port in this case.
- Wireless network (if applicable)
  - [x] Association with AP must be possible on all radios
  - [x] Association with 802.11s mesh must work on all radios
  - [x] AP+mesh mode must work in parallel on all radios
- LED mapping
  - Power/system LED
    - [x] Lit while the device is on
    - [x] Should display config mode blink sequence
          (https://gluon.readthedocs.io/en/latest/features/configmode.html)
  - Radio LEDs
    - [x] Should map to their respective radio
    - [x] Should show activity
  - Switch port LEDs
    - [x] Should map to their respective port (or switch, if only one led present)
    - [x] Should show link state and activity
2022-05-21 14:17:29 +02:00
J. Burfeind
02edf564bd
ath79-generic: (re)add CPE210v3 (#2506)
Gone due to
commit 45c84a117b ("ar71xx: drop target")
2022-05-13 23:36:34 +02:00
J. Burfeind
523dead05b
ath79-generic: (re)add support for wndr3700 (#2482)
Gone due to
commit 45c84a117b ("ar71xx: drop target")
2022-05-11 23:00:43 +02:00
J. Burfeind
743ba02fe9
ramips-mt76x8: add support for TP-Link Archer C20 v4 (#2500)
Co-authored-by: Ilja Gerhardt <ilja@cryptix.net>

Co-authored-by: Ilja Gerhardt <ilja@cryptix.net>
2022-05-05 11:10:07 +02:00
J. Burfeind
40f8275918
ath79-generic: (re)add Archer C7 v4 (#2497)
Gone due to
commit 45c84a117b ("ar71xx: drop target")
2022-05-05 01:19:29 +02:00
J. Burfeind
ab3e831b7c
ath79-generic: (re)add support for tl-wdr3500-v1 (#2450)
Gone due to
commit 45c84a117b ("ar71xx: drop target")
2022-05-04 00:33:05 +02:00
Andreas Ziegler
948d3e10e7
ath79-generic: (re)add support for archer-c59-v1 (#2489) 2022-05-01 19:38:12 +02:00
J. Burfeind
4ec8c4db19
ath79-generic: (re)add support for gl-usb150 (#2476)
Gone due to
commit 45c84a117b ("ar71xx: drop target")
2022-05-01 19:36:13 +02:00
Tom Herbers
aef006e02e
mpc85xx-p1020: add Extreme Networks WS-AP3825i (#2495) 2022-05-01 10:43:32 +02:00
David Bauer
90dfd25e06 mpc85xx-p1010: remove TP-Link WDR4900
Remove support for the TP-Link WDR4900, as it us currently unable to
load its kernel sure to factory bootloader constraints.

Progress on this topic is tracked in #2491
2022-04-30 16:35:44 +02:00
David Bauer
099d2bd693
docs: fix mpc85xx-p1010 target name (#2492)
The mpc85xx-generic target was renamed to mpc85xx-p1010 in OpenWrt
21.02. The target name in Gluon docs was never adjusted however.

Signed-off-by: David Bauer <mail@david-bauer.net>
2022-04-25 00:02:08 +02:00
J. Burfeind
374b81ddc0
ath79-generic: (re)add support for wndr3700v2 (#2485)
Gone due to
commit 45c84a117b ("ar71xx: drop target")
2022-04-21 22:34:11 +02:00
eberhab
9ec4abd043
ramips-mt76x8: add support for TP-Link Archer C20 v5 (#2481)
https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=86e7353bff2a5de257de8ec62e782f016eed143c

Co-authored-by: Tom Herbers <mail@tomherbers.de>
2022-04-17 20:47:27 +02:00
Tom Herbers
588502cff1
ath79-generic: (re)add support for tl-wr1043n-v5 (#2483)
Gone due to
commit 45c84a117b ("ar71xx: drop target")
2022-04-17 20:31:43 +02:00
Manu.WTF
f63fa832fd
ath79-generic: (re)add support for unifiac-pro (#2439) 2022-04-17 11:56:19 +02:00
J. Burfeind
684b4a80a0
ath79-generic: (re)add support for wbs210v1 (#2461)
Gone due to
commit 45c84a117b ("ar71xx: drop target")
2022-04-08 00:18:34 +02:00
J. Burfeind
8e9a186e5a
ath79-generic: (re)add support for glinet_6416 (#2453)
Gone due to
commit 45c84a117b ("ar71xx: drop target")
2022-04-05 23:02:54 +02:00
J. Burfeind
94e04393b1
ath79-nand: (re)add support for glinet_gl-ar300m (#2455)
Gone due to
commit 45c84a117b ("ar71xx: drop target")

Changed subtarget in between, similar change in
commit bed66fa248 ("ath79: move GL.iNet GL-AR750S to NAND subtarget")
2022-04-05 19:29:02 +02:00
J. Burfeind
5a0c299d8c
ath79-generic: (re)add support for tl-wr842nd-v3 (#2451)
Gone due to
commit 45c84a117b ("ar71xx: drop target")
2022-04-05 19:26:00 +02:00
Manu.WTF
2ea793f9b2
ath79-generic: (re)add support for avm_fritz4020 (#2435) 2022-04-04 19:08:38 +02:00
J. Burfeind
7c268290ee
ath79-generic: (re)add support for tl-wr1043nd-v2 (#2452)
Gone due to
commit 45c84a117b ("ar71xx: drop target")
2022-04-03 16:12:01 +02:00
J. Burfeind
a3c69d539d
ath79-generic: (re)add support for GL-AR750 (#2454)
Gone due to
commit 45c84a117b ("ar71xx: drop target")
2022-04-03 15:55:12 +02:00
J. Burfeind
dfa209a88a
ath79-generic: (re)add NanoStation M2/M5 (XW) (#2443)
Gone due to
commit 45c84a117b ("ar71xx: drop target")
2022-04-03 00:01:38 +02:00
aiyion.prime
d3a2c657f9 ath79-generic: (re)add unifi-ap-ac-lite
Gone due to
commit 45c84a117b ("ar71xx: drop target")
2022-04-02 15:49:36 +02:00
aiyion.prime
b901dfa691 ath79-generic: (re)add unifi-ap-ac-lr
Gone due to
commit 45c84a117b ("ar71xx: drop target")
2022-04-02 15:46:16 +02:00
J. Burfeind
6fe1e64f27
ath79-generic: (re)add Archer C5 v1 (#2427)
Gone due to
commit 45c84a117b ("ar71xx: drop target")
2022-04-02 00:18:47 +02:00
J. Burfeind
023c9af9dd
ath79-generic: (re)add Archer C7 v5 (#2436)
Gone due to
commit 45c84a117b ("ar71xx: drop target")
2022-03-31 18:15:12 +02:00
Manu.WTF
e2aaccda57
ath79-generic: (re)add support for tl-wr810n-v1 (#2442) 2022-03-31 16:21:44 +02:00
J. Burfeind
dbdf532867
ath79-generic: (re)add support for GL-AR150 (#2441)
Gone due to
commit 45c84a117b ("ar71xx: drop target")
2022-03-31 08:16:39 +02:00
David Bauer
55da2a7b0e
mpc85xx-p1010: add Sophos RED 15w rev.1 (#2438)
This adds support for the Sophos RED 15w rev.1 gateway.

It is a branch-office SD-WAN device based on the P1014 networking SoC.

Signed-off-by: David Bauer <mail@david-bauer.net>
2022-03-30 17:19:08 +02:00
Manu.WTF
8fdda51f98
ath79-generic: (re)add support for archer-c7-v2 (#2437) 2022-03-29 17:54:08 +02:00
aiyion.prime
4ea3478ba0 ath79-generic: (re)add support for tl-wr1043nd-v4
Gone due to
commit 45c84a117b ("ar71xx: drop target")
2022-03-26 12:45:07 +01:00
J. Burfeind
39c3c7adf3
ath79-generic: (re)add support for UniFi AP PRO (#2416)
Ubiquiti UniFi AP PRO

Gone due to
commit 45c84a1 ("ar71xx: drop target")
2022-03-26 11:11:32 +01:00
J. Burfeind
087c15ae0c
ath79-generic: (re)add support for UniFi AC Mesh (#2428)
Gone due to
commit 45c84a117b ("ar71xx: drop target")
2022-03-26 10:52:35 +01:00
J. Burfeind
1bfad8ff02
ath79-generic: (re)add support for CPE510 v1.x (#2430)
Gone due to
commit 45c84a117b ("ar71xx: drop target")
2022-03-25 23:39:19 +01:00
Sebastian Schaper
9751744797
ath79: migrate D-Link DAP-1330 and DIR-550 from ar71xx (#2417)
also add DAP-1365, which is a different case variant of DAP-1330

Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
2022-03-25 22:23:55 +01:00
J. Burfeind
d1b801b202
ath79-generic: (re)add support for tl-wr1043nd-v3 (#2415)
Gone due to
commit 45c84a1 ("ar71xx: drop target")
2022-03-25 20:37:12 +01:00
J. Burfeind
fd8d5a3cdb
ath79-generic: (re)add support for CPE210 v2.x (#2429)
Gone due to
commit 45c84a117b ("ar71xx: drop target")
2022-03-25 18:21:24 +01:00
Matthias Schiffer
138792e7eb
Merge pull request #2421 from AiyionPrime/ath79-migrate-ubnt-uap
ath79-generic: (re)add support for UniFi AP
2022-03-24 21:31:39 +01:00
J. Burfeind
a5ada094bf
ath79-generic: (re)add support for CPE210 v1.x (#2410)
Gone due to
commit 45c84a117b ("ar71xx: drop target")
2022-03-24 19:21:45 +01:00
aiyion.prime
71d3f4cad1 ath79-generic: (re)add support for UniFi AP LR
Gone due to
commit 45c84a1 ("ar71xx: drop target")
2022-03-24 12:09:22 +01:00
aiyion.prime
aa5355f662 ath79-generic: (re)add support for UniFi AP
Gone due to
commit 45c84a1 ("ar71xx: drop target")
2022-03-24 12:07:31 +01:00
Matthias Schiffer
086aa7afa0
Merge pull request #2325 from FreifunkVogtland/ath79-openmesh
ath79-generic: Re-add OpenMesh devices
2022-03-24 09:21:03 +01:00
Sebastian Schaper
866bf11903
ath79-generic: add support for D-Link DAP-2660 A1 (#2414)
Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
2022-03-23 23:35:39 +01:00
J. Burfeind
d9c7b1c6fc
ath79-generic: (re)add AVM Fritz!WLAN Repeater 450e (#2420)
Gone due to
commit 45c84a117b ("ar71xx: drop target")
2022-03-23 20:14:51 +01:00
Sven Eckelmann
979cc0a2ed ath79-generic: Add support for OpenMesh OM5P-AN
Device specifications:
======================

* Qualcomm/Atheros AR9344 rev 2
* 560/450/225 MHz (CPU/DDR/AHB)
* 64 MB of RAM
* 16 MB of SPI NOR flash
  - 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 1T1R 2.4 GHz Wi-Fi
* 2T2R 5 GHz Wi-Fi
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* TI tmp423 (package kmod-hwmon-tmp421) for temperature monitoring
* 2x ethernet
  - eth0
    + AR8035 ethernet PHY
    + 10/100/1000 Mbps Ethernet
    + 802.3af POE
    + used as LAN interface
  - eth1
    + 10/100 Mbps Ethernet
    + builtin switch port 1
    + 18-24V passive POE (mode B)
    + used as WAN interface
* 12-24V 1A DC
* internal antennas

Flashing instructions:
======================

Various methods can be used to install the actual image on the flash.
Two easy ones are:

ap51-flash
----------

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.

initramfs from TFTP
-------------------

The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):

    setenv serverip 192.168.1.21
    setenv ipaddr 192.168.1.1
    tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr

The actual sysupgrade image can then be transferred (on the LAN port) to the
device via

    scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/

On the device, the sysupgrade must then be started using

    sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
2022-03-21 09:37:03 +01:00
Sven Eckelmann
4ff8f2f770 ath79-generic: Add support for OpenMesh OM5P-AC v2
Device specifications:
======================

* Qualcomm/Atheros QCA9558 ver 1 rev 0
* 720/600/200 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
  - 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2T2R 2.4 GHz Wi-Fi (11n)
* 2T2R 5 GHz Wi-Fi (11ac)
* 4x GPIO-LEDs (3x wifi, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default))
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* TI tmp423 (package kmod-hwmon-tmp421) for temperature monitoring
* 2x ethernet
  - eth0
    + AR8035 ethernet PHY (RGMII)
    + 10/100/1000 Mbps Ethernet
    + 802.3af POE
    + used as LAN interface
  - eth1
    + AR8031 ethernet PHY (RGMII)
    + 10/100/1000 Mbps Ethernet
    + 18-24V passive POE (mode B)
    + used as WAN interface
* 12-24V 1A DC
* internal antennas

This device support is based on the partially working stub from commit
53c474abbdfe ("ath79: add new OF only target for QCA MIPS silicon").

Flashing instructions:
======================

Various methods can be used to install the actual image on the flash.
Two easy ones are:

ap51-flash
----------

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.

initramfs from TFTP
-------------------

The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):

    setenv serverip 192.168.1.21
    setenv ipaddr 192.168.1.1
    tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr

The actual sysupgrade image can then be transferred (on the LAN port) to the
device via

    scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/

On the device, the sysupgrade must then be started using

    sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin

Gluon image name change
=======================

The device had the image name "openmesh-om5p-acv2" in older versions of Gluon.
This had to be changed with the new name in the device trees of the ath79
device tree.
2022-03-21 09:37:03 +01:00
Sven Eckelmann
6e35f6b95a ath79-generic: Add support for OpenMesh OM5P-AC v1
Device specifications:
======================

* Qualcomm/Atheros QCA9558 ver 1 rev 0
* 720/600/240 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
  - 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2T2R 2.4 GHz Wi-Fi (11n)
* 2T2R 5 GHz Wi-Fi (11ac)
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* external h/w watchdog (enabled by default))
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* TI tmp423 (package kmod-hwmon-tmp421) for temperature monitoring
* 2x ethernet
  - eth0
    + AR8035 ethernet PHY (RGMII)
    + 10/100/1000 Mbps Ethernet
    + 802.3af POE
    + used as LAN interface
  - eth1
    + AR8035 ethernet PHY (SGMII)
    + 10/100/1000 Mbps Ethernet
    + 18-24V passive POE (mode B)
    + used as WAN interface
* 12-24V 1A DC
* internal antennas

Flashing instructions:
======================

Various methods can be used to install the actual image on the flash.
Two easy ones are:

ap51-flash
----------

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.

initramfs from TFTP
-------------------

The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):

    setenv serverip 192.168.1.21
    setenv ipaddr 192.168.1.1
    tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr

The actual sysupgrade image can then be transferred (on the LAN port) to the
device via

    scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/

On the device, the sysupgrade must then be started using

    sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin

Gluon image name change
=======================

The device had the image name "openmesh-om5p-ac" in older versions of Gluon.
This had to be changed with the new name in the device trees of the ath79
device tree.
2022-03-21 09:37:03 +01:00
Sven Eckelmann
e0abce03e6 ath79-generic: Add support for OpenMesh OM5P
Device specifications:
======================

* Qualcomm/Atheros AR9344 rev 2
* 560/450/225 MHz (CPU/DDR/AHB)
* 64 MB of RAM
* 16 MB of SPI NOR flash
  - 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2x 10/100 Mbps Ethernet
* 2T2R 5 GHz Wi-Fi
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x fast ethernet
  - eth0
    + builtin switch port 1
    + used as LAN interface
  - eth1
    + 18-24V passive POE (mode B)
    + used as WAN interface
* 12-24V 1A DC
* internal antennas

WAN/LAN LEDs appear to be wrong in ar71xx and have been swapped here.

Flashing instructions:
======================

Various methods can be used to install the actual image on the flash.
Two easy ones are:

ap51-flash
----------

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.

initramfs from TFTP
-------------------

The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):

    setenv serverip 192.168.1.21
    setenv ipaddr 192.168.1.1
    tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr

The actual sysupgrade image can then be transferred (on the LAN port) to the
device via

    scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/

On the device, the sysupgrade must then be started using

    sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
2022-03-21 09:37:03 +01:00
Sven Eckelmann
d427c94ee0 ath79-generic: Add support for OpenMesh OM2P-LC
Device specifications:
======================

* Qualcomm/Atheros AR9330 rev 1
* 400/400/200 MHz (CPU/DDR/AHB)
* 64 MB of RAM
* 16 MB of SPI NOR flash
  - 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2x 10/100 Mbps Ethernet
* 1T1R 2.4 GHz Wi-Fi
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x fast ethernet
  - eth0
    + builtin switch port 1
    + used as LAN interface
  - eth1
    + 18-24V passive POE (mode B)
    + used as WAN interface
* 12-24V 1A DC
* internal antennas

Flashing instructions:
======================

Various methods can be used to install the actual image on the flash.
Two easy ones are:

ap51-flash
----------

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.

initramfs from TFTP
-------------------

The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):

    setenv serverip 192.168.1.21
    setenv ipaddr 192.168.1.1
    tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr

The actual sysupgrade image can then be transferred (on the LAN port) to
the device via

    scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/

On the device, the sysupgrade must then be started using

    sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
2022-03-21 09:37:03 +01:00
Sven Eckelmann
03d894f33a ath79-generic: Add support for OpenMesh OM2P-HS v4
Device specifications:
======================

* Qualcomm/Atheros QCA9533 v2
* 650/600/217 MHz (CPU/DDR/AHB)
* 64 MB of RAM
* 16 MB of SPI NOR flash
  - 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2x 10/100 Mbps Ethernet
* 2T2R 2.4 GHz Wi-Fi
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x fast ethernet
  - eth0
    + 24V passive POE (mode B)
    + used as WAN interface
  - eth1
    + 802.3af POE
    + builtin switch port 1
    + used as LAN interface
* 12-24V 1A DC
* internal antennas

Flashing instructions:
======================

Various methods can be used to install the actual image on the flash.
Two easy ones are:

ap51-flash
----------

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.

initramfs from TFTP
-------------------

The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):

    setenv serverip 192.168.1.21
    setenv ipaddr 192.168.1.1
    tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr

The actual sysupgrade image can then be transferred (on the LAN port) to
the device via

    scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/

On the device, the sysupgrade must then be started using

    sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin

Gluon image name change
=======================

The device had the image name "openmesh-om2phsv4" in older versions of Gluon.
This had to be changed with the new name in the device trees of the ath79
device tree.
2022-03-21 09:37:03 +01:00
Sven Eckelmann
eed91a9be6 ath79-generic: add support for OpenMesh OM2P-HS v3
Device specifications:
======================

* Qualcomm/Atheros AR9341 rev 1
* 535/400/200 MHz (CPU/DDR/AHB)
* 64 MB of RAM
* 16 MB of SPI NOR flash
  - 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2x 10/100 Mbps Ethernet
* 2T2R 2.4 GHz Wi-Fi
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x fast ethernet
  - eth0
    + 802.3af POE
    + builtin switch port 1
    + used as LAN interface
  - eth1
    + 18-24V passive POE (mode B)
    + used as WAN interface
* 12-24V 1A DC
* internal antennas

Flashing instructions:
======================

Various methods can be used to install the actual image on the flash.
Two easy ones are:

ap51-flash
----------

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.

initramfs from TFTP
-------------------

The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):

    setenv serverip 192.168.1.21
    setenv ipaddr 192.168.1.1
    tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr

The actual sysupgrade image can then be transferred (on the LAN port) to
the device via

    scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/

On the device, the sysupgrade must then be started using

    sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin

Gluon image name change
=======================

The device had the image name "openmesh-om2phsv3" in older versions of Gluon.
This had to be changed with the new name in the device trees of the ath79
device tree.
2022-03-21 09:37:03 +01:00
Sven Eckelmann
ce324d11ec ath79-generic: add support for OpenMesh OM2P-HS v2
Device specifications:
======================

* Qualcomm/Atheros AR9341 rev 1
* 535/400/200 MHz (CPU/DDR/AHB)
* 64 MB of RAM
* 16 MB of SPI NOR flash
  - 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2x 10/100 Mbps Ethernet
* 2T2R 2.4 GHz Wi-Fi
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x fast ethernet
  - eth0
    + 802.3af POE
    + builtin switch port 1
    + used as LAN interface
  - eth1
    + 18-24V passive POE (mode B)
    + used as WAN interface
* 12-24V 1A DC
* internal antennas

Flashing instructions:
======================

Various methods can be used to install the actual image on the flash.
Two easy ones are:

ap51-flash
----------

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.

initramfs from TFTP
-------------------

The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):

    setenv serverip 192.168.1.21
    setenv ipaddr 192.168.1.1
    tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr

The actual sysupgrade image can then be transferred (on the LAN port) to
the device via

    scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/

On the device, the sysupgrade must then be started using

    sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin

Gluon image name change
=======================

The device had the image name "openmesh-om2phsv2" in older versions of Gluon.
This had to be changed with the new name in the device trees of the ath79
device tree.
2022-03-21 09:37:03 +01:00
Sven Eckelmann
19026314d7 ath79-generic: add support for OpenMesh OM2P-HS v1
Device specifications:
======================

* Qualcomm/Atheros AR9341 rev 1
* 535/400/200 MHz (CPU/DDR/AHB)
* 64 MB of RAM
* 16 MB of SPI NOR flash
  - 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2x 10/100 Mbps Ethernet
* 2T2R 2.4 GHz Wi-Fi
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x fast ethernet
  - eth0
    + 802.3af POE
    + builtin switch port 1
    + used as LAN interface
  - eth1
    + 18-24V passive POE (mode B)
    + used as WAN interface
* 12-24V 1A DC
* internal antennas

Flashing instructions:
======================

Various methods can be used to install the actual image on the flash.
Two easy ones are:

ap51-flash
----------

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.

initramfs from TFTP
-------------------

The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):

    setenv serverip 192.168.1.21
    setenv ipaddr 192.168.1.1
    tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr

The actual sysupgrade image can then be transferred (on the LAN port) to
the device via

    scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/

On the device, the sysupgrade must then be started using

    sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin

Gluon image name change
=======================

The device had the image name "openmesh-om2phs" in older versions of Gluon.
This had to be changed with the new name in the device trees of the ath79
device tree.
2022-03-21 09:37:03 +01:00
Sven Eckelmann
0cca0f5e7f ath79-generic: Add support for OpenMesh OM2P v4
Device specifications:
======================

* Qualcomm/Atheros QCA9533 v2
* 650/600/217 MHz (CPU/DDR/AHB)
* 64 MB of RAM
* 16 MB of SPI NOR flash
  - 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2x 10/100 Mbps Ethernet
* 1T1R 2.4 GHz Wi-Fi
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x fast ethernet
  - eth0
    + Label: Ethernet 1
    + 24V passive POE (mode B)
  - eth1
    + Label: Ethernet 2
    + 802.3af POE
    + builtin switch port 1
* 12-24V 1A DC
* external antenna

Flashing instructions:
======================

Various methods can be used to install the actual image on the flash.
Two easy ones are:

ap51-flash
----------

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.

initramfs from TFTP
-------------------

The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):

    setenv serverip 192.168.1.21
    setenv ipaddr 192.168.1.1
    tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr

The actual sysupgrade image can then be transferred (on the LAN port) to
the device via

    scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/

On the device, the sysupgrade must then be started using

    sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin

Gluon image name change
=======================

The device had the image name "openmesh-om2pv4" in older versions of Gluon.
This had to be changed with the new name in the device trees of the ath79
device tree.
2022-03-21 09:37:03 +01:00
Sven Eckelmann
5a64deec9a ath79-generic: Add support for OpenMesh OM2P v2
Device specifications:
======================

* Qualcomm/Atheros AR9330 rev 1
* 400/400/200 MHz (CPU/DDR/AHB)
* 64 MB of RAM
* 16 MB of SPI NOR flash
  - 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2x 10/100 Mbps Ethernet
* 1T1R 2.4 GHz Wi-Fi
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x fast ethernet
  - eth0
    + builtin switch port 1
    + used as LAN interface
  - eth1
    + 18-24V passive POE (mode B)
    + used as WAN interface
* 12-24V 1A DC
* external antenna

Flashing instructions:
======================

Various methods can be used to install the actual image on the flash.
Two easy ones are:

ap51-flash
----------

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.

initramfs from TFTP
-------------------

The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):

    setenv serverip 192.168.1.21
    setenv ipaddr 192.168.1.1
    tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr

The actual sysupgrade image can then be transferred (on the LAN port) to
the device via

    scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/

On the device, the sysupgrade must then be started using

    sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin

Gluon image name change
=======================

The device had the image name "openmesh-om2pv2" in older versions of Gluon.
This had to be changed with the new name in the device trees of the ath79
device tree.
2022-03-21 09:37:03 +01:00
Sven Eckelmann
47eda6a501 ath79-generic: Add support for OpenMesh OM2P v1
Device specifications:
======================

* Qualcomm/Atheros AR7240 rev 2
* 350/350/175 MHz (CPU/DDR/AHB)
* 32 MB of RAM
* 16 MB of SPI NOR flash
  - 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2x 10/100 Mbps Ethernet
* 1T1R 2.4 GHz Wi-Fi
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x fast ethernet
  - eth0
    + 18-24V passive POE (mode B)
    + used as WAN interface
  - eth1
    + builtin switch port 4
    + used as LAN interface
* 12-24V 1A DC
* external antenna

The device itself requires the mtdparts from the uboot arguments to
properly boot the flashed image and to support dual-boot (primary +
recovery image). Unfortunately, the name of the mtd device in mtdparts is
still using the legacy name "ar7240-nor0" which must be supplied using the
Linux-specfic DT parameter linux,mtd-name to overwrite the generic name
"spi0.0".

Flashing instructions:
======================

Various methods can be used to install the actual image on the flash.
Two easy ones are:

ap51-flash
----------

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.

initramfs from TFTP
-------------------

The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):

    setenv serverip 192.168.1.21
    setenv ipaddr 192.168.1.1
    tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr

The actual sysupgrade image can then be transferred (on the LAN port) to the
device via

    scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/

On the device, the sysupgrade must then be started using

    sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin

Gluon image name change
=======================

The device had the image name "openmesh-om2p" in older versions of Gluon.
This had to be changed with the new name in the device trees of the ath79
device tree.
2022-03-21 09:37:03 +01:00
Sven Eckelmann
bc71c915d2 ath79-generic: Add support for OpenMesh MR1750 v2
Device specifications:
======================

* Qualcomm/Atheros QCA9558 ver 1 rev 0
* 720/600/240 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
  - 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 3T3R 2.4 GHz Wi-Fi (11n)
* 3T3R 5 GHz Wi-Fi (11ac)
* 6x GPIO-LEDs (2x wifi, 2x status, 1x lan, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default))
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 1x ethernet
  - AR8035 ethernet PHY (RGMII)
  - 10/100/1000 Mbps Ethernet
  - 802.3af POE
  - used as LAN interface
* 12-24V 1A DC
* internal antennas

Flashing instructions:
======================

Various methods can be used to install the actual image on the flash.
Two easy ones are:

ap51-flash
----------

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.

initramfs from TFTP
-------------------

The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):

    setenv serverip 192.168.1.21
    setenv ipaddr 192.168.1.1
    tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr

The actual sysupgrade image can then be transferred (on the LAN port) to the
device via

    scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/

On the device, the sysupgrade must then be started using

    sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin

Gluon image name change
=======================

The device had the image name "openmesh-mr1750v2" in older versions of Gluon.
This had to be changed with the new name in the device trees of the ath79
device tree.
2022-03-21 09:37:03 +01:00
Sven Eckelmann
39750f19f8 ath79-generic: Add support for OpenMesh MR1750 v1
Device specifications:
======================

* Qualcomm/Atheros QCA9558 ver 1 rev 0
* 720/600/240 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
  - 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 3T3R 2.4 GHz Wi-Fi (11n)
* 3T3R 5 GHz Wi-Fi (11ac)
* 6x GPIO-LEDs (2x wifi, 2x status, 1x lan, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default))
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 1x ethernet
  - AR8035 ethernet PHY (RGMII)
  - 10/100/1000 Mbps Ethernet
  - 802.3af POE
  - used as LAN interface
* 12-24V 1A DC
* internal antennas

Flashing instructions:
======================

Various methods can be used to install the actual image on the flash.
Two easy ones are:

ap51-flash
----------

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.

initramfs from TFTP
-------------------

The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):

    setenv serverip 192.168.1.21
    setenv ipaddr 192.168.1.1
    tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr

The actual sysupgrade image can then be transferred (on the LAN port) to the
device via

    scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/

On the device, the sysupgrade must then be started using

    sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin

Gluon image name change
=======================

The device had the image name "openmesh-mr1750" in older versions of Gluon.
This had to be changed with the new name in the device trees of the ath79
device tree.
2022-03-21 09:37:03 +01:00
Sven Eckelmann
0de095fe9f ath79-generic: Add support for OpenMesh MR900 v2
Device specifications:
======================

* Qualcomm/Atheros QCA9558 ver 1 rev 0
* 720/600/240 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
  - 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 3T3R 2.4 GHz Wi-Fi
* 3T3R 5 GHz Wi-Fi
* 6x GPIO-LEDs (2x wifi, 2x status, 1x lan, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default))
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 1x ethernet
  - AR8035 ethernet PHY (RGMII)
  - 10/100/1000 Mbps Ethernet
  - 802.3af POE
  - used as LAN interface
* 12-24V 1A DC
* internal antennas

Flashing instructions:
======================

Various methods can be used to install the actual image on the flash.
Two easy ones are:

ap51-flash
----------

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.

initramfs from TFTP
-------------------

The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):

    setenv serverip 192.168.1.21
    setenv ipaddr 192.168.1.1
    tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr

The actual sysupgrade image can then be transferred (on the LAN port) to the
device via

    scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/

On the device, the sysupgrade must then be started using

    sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin

Gluon image name change
=======================

The device had the image name "openmesh-mr900v2" in older versions of Gluon.
This had to be changed with the new name in the device trees of the ath79
device tree.
2022-03-21 09:37:03 +01:00
Sven Eckelmann
9d794294b0 ath79-generic: Add support for OpenMesh MR900 v1
Device specifications:
======================

* Qualcomm/Atheros QCA9558 ver 1 rev 0
* 720/600/240 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
  - 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 3T3R 2.4 GHz Wi-Fi
* 3T3R 5 GHz Wi-Fi
* 6x GPIO-LEDs (2x wifi, 2x status, 1x lan, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default))
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 1x ethernet
  - AR8035 ethernet PHY (RGMII)
  - 10/100/1000 Mbps Ethernet
  - 802.3af POE
  - used as LAN interface
* 12-24V 1A DC
* internal antennas

Flashing instructions:
======================

Various methods can be used to install the actual image on the flash.
Two easy ones are:

ap51-flash
----------

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.

initramfs from TFTP
-------------------

The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):

    setenv serverip 192.168.1.21
    setenv ipaddr 192.168.1.1
    tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr

The actual sysupgrade image can then be transferred (on the LAN port) to the
device via

    scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/

On the device, the sysupgrade must then be started using

    sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin

Gluon image name change
=======================

The device had the image name "openmesh-mr900" in older versions of Gluon.
This had to be changed with the new name in the device trees of the ath79
device tree.
2022-03-21 09:37:03 +01:00
Sven Eckelmann
dd7eac7e7f ath79-generic: Add support for OpenMesh MR600 v2
Device specifications:
======================

* Qualcomm/Atheros AR9344 rev 2
* 560/450/225 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
  - 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2T2R 2.4 GHz Wi-Fi
* 2T2R 5 GHz Wi-Fi
* 8x GPIO-LEDs (6x wifi, 1x wps, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default))
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 1x ethernet
  - AR8035 ethernet PHY (RGMII)
  - 10/100/1000 Mbps Ethernet
  - 802.3af POE
  - used as LAN interface
* 12-24V 1A DC
* internal antennas

Flashing instructions:
======================

Various methods can be used to install the actual image on the flash.
Two easy ones are:

ap51-flash
----------

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.

initramfs from TFTP
-------------------

The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):

    setenv serverip 192.168.1.21
    setenv ipaddr 192.168.1.1
    tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr

The actual sysupgrade image can then be transferred (on the LAN port) to the
device via

    scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/

On the device, the sysupgrade must then be started using

    sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin

Gluon image name change
=======================

The device had the image name "openmesh-mr600v2" in older versions of Gluon.
This had to be changed with the new name in the device trees of the ath79
device tree.
2022-03-21 09:37:03 +01:00
Sven Eckelmann
e2ccf75342 ath79-generic: Add support for OpenMesh MR600 v1
Device specifications:
======================

* Qualcomm/Atheros AR9344 rev 2
* 560/450/225 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
  - 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2T2R 2.4 GHz Wi-Fi
* 2T2R 5 GHz Wi-Fi
* 4x GPIO-LEDs (2x wifi, 1x wps, 1x power)
* 1x GPIO-button (reset)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 1x ethernet
  - AR8035 ethernet PHY (RGMII)
  - 10/100/1000 Mbps Ethernet
  - 802.3af POE
  - used as LAN interface
* 12-24V 1A DC
* internal antennas

Flashing instructions:
======================

Various methods can be used to install the actual image on the flash.
Two easy ones are:

ap51-flash
----------

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.

initramfs from TFTP
-------------------

The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):

    setenv serverip 192.168.1.21
    setenv ipaddr 192.168.1.1
    tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr

The actual sysupgrade image can then be transferred (on the LAN port) to the
device via

    scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/

On the device, the sysupgrade must then be started using

    sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin

Gluon image name change
=======================

The device had the image name "openmesh-mr600" in older versions of Gluon.
This had to be changed with the new name in the device trees of the ath79
device tree.
2022-03-21 09:37:03 +01:00
Sven Eckelmann
767b4123cf ath79-generic: Add support for OpenMesh A40
Device specifications:
======================

* Qualcomm/Atheros QCA9558 ver 1 rev 0
* 720/600/240 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
  - 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2T2R 2.4 GHz Wi-Fi (11n)
* 2T2R 5 GHz Wi-Fi (11ac)
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default))
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x ethernet
  - eth0
    + Label: Ethernet 1
    + AR8035 ethernet PHY (RGMII)
    + 10/100/1000 Mbps Ethernet
    + 802.3af POE
    + used as WAN interface
  - eth1
    + Label: Ethernet 2
    + AR8035 ethernet PHY (SGMII)
    + 10/100/1000 Mbps Ethernet
    + used as LAN interface
* 1x USB
* internal antennas

Flashing instructions:
======================

Various methods can be used to install the actual image on the flash.
Two easy ones are:

ap51-flash
----------

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.

initramfs from TFTP
-------------------

The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):

    setenv serverip 192.168.1.21
    setenv ipaddr 192.168.1.1
    tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr

The actual sysupgrade image can then be transferred (on the LAN port) to the
device via

    scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/

On the device, the sysupgrade must then be started using

    sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
2022-03-21 09:37:03 +01:00
Sven Eckelmann
df114faec0 ath79-generic: Add support for OpenMesh A60
Device specifications:
======================

* Qualcomm/Atheros QCA9558 ver 1 rev 0
* 720/600/240 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
  - 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 3T3R 2.4 GHz Wi-Fi (11n)
* 3T3R 5 GHz Wi-Fi (11ac)
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default))
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x ethernet
  - eth0
    + Label: Ethernet 1
    + AR8035 ethernet PHY (RGMII)
    + 10/100/1000 Mbps Ethernet
    + 802.3af POE
    + used as WAN interface
  - eth1
    + Label: Ethernet 2
    + AR8031 ethernet PHY (SGMII)
    + 10/100/1000 Mbps Ethernet
    + used as LAN interface
* 1x USB
* internal antennas

Flashing instructions:
======================

Various methods can be used to install the actual image on the flash.
Two easy ones are:

ap51-flash
----------

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.

initramfs from TFTP
-------------------

The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):

    setenv serverip 192.168.1.21
    setenv ipaddr 192.168.1.1
    tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr

The actual sysupgrade image can then be transferred (on the LAN port) to the
device via

    scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/

On the device, the sysupgrade must then be started using

    sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
2022-03-21 09:37:03 +01:00
David Bauer
a3203b26c4
Merge pull request #2372 from freifunk-gluon/uci-regen
Regenerate network and system UCI configs on every reconfigure, switch to role-based interface configuration
2022-03-20 17:54:04 +01:00
Steffen Förster
6ecc0e9fd6 docs: fix invalid fritztools link 2022-03-16 15:28:49 +01:00
Matthias Schiffer
210cacdf55
docs: update for role-based interface configuration 2022-02-22 18:52:15 +01:00
Matthias Schiffer
62b24ed7ce
gluon-web-osm: update OpenLayers default URL to 5.3.0
The OpenLayers JS/CSS download URL is dead. Update it to make the map
work again:

- Update from OpenLayers 5.2.0 to 5.3.0
- Switch from the obsolete rawgit.com URL to jsdelivr.net (rawgit.com
  was only redirecting to jsdelivr.net for the last few years anyways)
- Set a fixed commit in the URL, so the URL doesn't become outdated again
2022-02-13 22:07:36 +01:00
Luflosi
55e95dd49b
ath79-generic: add support for TP-Link Archer A7 v5 (#2374) 2022-01-14 23:20:22 +01:00
Matthias Schiffer
adda317176
build: set GLUON_DEPRECATED = 0 by default
We currently don't have any deprecated devices, so it doesn't make much
sense to force every site to specify this variable. Make it default to 0
instead.
2021-12-31 14:44:47 +01:00
Matthias Schiffer
efb4a4f637
docs: user/getting_started: add a footnote regarding make update
Add some explanation when `make update` needs to be run again.
2021-12-31 02:50:23 +01:00
Matthias Schiffer
ac3ac29158
docs: minor grammer/wording fixes 2021-12-24 14:18:16 +01:00
Matthias Schiffer
854fef4e12
docs: consistently indent .rst files with 2 spaces
2 spaces is the most common indentation width used in the docs; adjust
the rest for consistency.

Also change .editorconfig accordingly.
2021-12-24 14:16:04 +01:00
Martin Weinelt
6728c4a103
Add helper to run a containerized build environment (#2292)
Using `make container` or, if you don't have automake/gmake on your host
system, `./scripts/container.sh` will build an image for the current
branch your are on and drop you into a shell running inside a container
using that image.

From there all tooling required to work on Gluon is available.

Supports both podman (preferred) and docker.
2021-12-21 21:40:27 +01:00
David Bauer
102a4b9350
ath79-generic: add support for Enterasys WS-AP3705i (#2332) 2021-11-01 00:38:36 +01:00
Manu.WTF
1eeca33c8d
ramips-mt7621: add support for Ubiquiti UniFi 6 Lite (#2310)
Hardware
--------
MediaTek MT7621AT
256M DDR3
32M SPI-NOR
MediaTek MT7603 2T2R 802.11n 2.4GHz
MediaTek MT7915 2T2R 802.11ax 5GHz

Not Working
-----------
 - Bluetooth (connected to UART3)

UART
----

UART is located in the lower left corner of the board. Pinout is

0 - 3V3 (don't connect)
1 - RX
2 - TX
3 - GND

Console is 115200 8N1.

Boot
----

1. Connect to the serial console and connect power.

2. Double-press ESC when prompted

3. Set the fdt address

   $ fdt addr $(fdtcontroladdr)

4. Remove the signature node from the control FDT

   $ fdt rm /signature

5. Transfer and boot the OpenWrt initramfs image to the device.
   Make sure to name the file C0A80114.img and have it reachable at
   192.168.1.1/24

   $ tftpboot; bootm

Installation
------------

1. Connect to the booted device at 192.168.1.20 using username/password
   "ubnt".

2. Update the bootloader environment.

   $ fw_setenv devmode TRUE
   $ fw_setenv boot_openwrt "fdt addr \$(fdtcontroladdr);
     fdt rm /signature; bootubnt"
   $ fw_setenv bootcmd "run boot_openwrt"

3. Transfer the OpenWrt sysupgrade image to the device using SCP.

4. Check the mtd partition number for bs / kernel0 / kernel1

   $ cat /proc/mtd

5. Set the bootselect flag to boot from kernel0

   $ dd if=/dev/zero bs=1 count=1 of=/dev/mtdblock4

6. Write the OpenWrt sysupgrade image to both kernel0 as well as kernel1

   $ dd if=openwrt.bin of=/dev/mtdblock6
   $ dd if=openwrt.bin of=/dev/mtdblock7

7. Reboot the device. It should boot into OpenWrt.
2021-09-15 00:44:34 +02:00
J. Burfeind
83d0e3274e
ath79-generic: add support for Onion Omega (#2306)
* ath79-generic: add support for Onion Omega

support was previously dropped in
commit 45c84a117b ("ar71xx: drop target")

* fixup! ath79-generic: add support for Onion Omega

* fixup! ath79-generic: add support for Onion Omega
2021-09-04 17:42:44 +02:00
Tom Herbers
794f4b2d3d
ramips-mt76x8: add support for GL.iNet microuter-N300 (#2303) 2021-09-04 17:42:16 +02:00
Björn Dobe
a492e629f8
ipq40xx: add support for Aruba AP-303H / Instant ON AP11D (#2302)
- [x] must be flashable from vendor firmware
  - [ ] webinterface
  - [ ] tftp
  - [x] other: Console port available. Manufacturer specific cable required.
        Tutorial in OpenWRT commit message https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=c6e972c8772a628a1a2f2e5590d7c6f4acef9ab0
- [x] must support upgrade mechanism
  - [x] must have working sysupgrade
    - [x] must keep/forget configuration (if applicable)
      *think `sysupgrade [-n]` or `firstboot`*
  - [x] must have working autoupdate
        root@Aruba-AP-303H:~# lua -e 'print(require("platform_info").get_image_name())'
        aruba-ap-303h
- [x] reset/wps/phone button must return device into config mode
- [x] primary mac should match address on device label (or packaging) (https://gluon.readthedocs.io/en/latest/dev/hardware.html#notes)
- wired network
  - [x] should support all network ports on the device
  - [x] must have correct port assignment (WAN/LAN)
- wifi (if applicable)
  - [x] association with AP must be possible on all radios
  - [x] association with 802.11s mesh must be working on all radios
  - [x] ap/mesh mode must work in parallel on all radios
- led mapping
  - power/sys led (_critical, because led definitions are setup on firstboot only_)
    - [x] lit while the device is on
    - [x] should display config mode blink sequence
(https://gluon.readthedocs.io/en/latest/features/configmode.html)
  - radio leds
    - [x] should map to their respective radio
    - [x] should show activity
  - switchport leds
    - [x] should map to their respective port (or switch, if only one led present)
    - [x] should show link state and activity
- outdoor devices only
  - [ ] added board name to `is_outdoor_device` function in `package/gluon-core/luasrc/usr/lib/lua/gluon/platform.lua`
- ToDo (upstream):
  - enable PoE pass through on interface E3
        system.poe_passthrough=gpio_switch
        system.poe_passthrough.name='PoE Passthrough'
        system.poe_passthrough.gpio_pin='446'
        system.poe_passthrough.value='0' (0 is active)
2021-09-01 23:31:01 +02:00
Tom Herbers
5a034be6b3
ath79-generic: add support for TP-Link EAP225-Outdoor v1 2021-08-28 18:52:52 +02:00
citronalco
34fc9544b8
ath79-generic: add support for TP-Link WBS210 v2 (#2299) 2021-08-27 23:15:04 +02:00
micw
a1b961994a
Add support for tp-link CPE510 V2 (#2287)
Co-authored-by: Michael Wyraz <michael.wyraz@evermind.de>
2021-08-12 17:14:38 +02:00
Martin Weinelt
e4086446cc
Use python3 in CI and documented build requirements
This has become possible with OpenWrt 21.02 and while the Dockerfile
already received that updated, we forgot to update the CI and the
documentation.
2021-08-12 01:27:50 +02:00
micw
6b699f376c
Add support for tp-link CPE510 V3 (#2283) 2021-08-11 19:15:37 +02:00
Matthias Schiffer
df06b05b2a
Merge pull request #2288 from freifunk-gluon/wdr3600
ath79-generic: add TP-Link TL-WDR3600/4300
2021-08-11 07:56:07 +02:00
David Bauer
14b1224f97
ipq40xx: add support for Aruba AP-365 / InstantOn AP17 (#2290) 2021-08-11 01:14:30 +02:00