The PHY lookup helper "find_phy_by_path" could not lookup the PHY name
for paths from multi-phy devices.
An example for such a path would be:
'1e140000.pcie/pci0000:00/0000:00:01.0/0000:02:00.0+1'
The integer after the plus (+) character determines the PHY index of the
specific device in relation to the PHY with the lowest index of the
device.
For example, if the device provides phy2 and phy3, the above path would
describe phy3. In case the device provides phy0 and phy1, it would
describe phy1.
Rewrite the "find_phy_by_path" function to support those paths as well
as regular device paths in a universal manner.
Signed-off-by: David Bauer <mail@david-bauer.net>
Delete all default network device sections upon first boot.
Only LAN & WAN networks are defined at this point. We are using the
legacy way of definiting bridges via the interface sections ifname
option.
The prior filtering was based upon a single device and didn't take into
consideration that DSA interface names can be named arbitrarily.
Signed-off-by: David Bauer <mail@david-bauer.net>
VoCores aren't exactly useful mesh nodes except for experimentation.
They certainly aren't worth maintaining a whole target, in particular
one that has a WLAN driver not used by any other target.
It was found that a one second timeout for nodeinfo data may be too low,
so that when a node is otherwise occupied that timeout may be reached
too often.
The nodeinfo query response is also vital to the status-page base
template, so that when it times out, the site will be turned in a broken
state, that it cannot recover from.
Fixes: #2256
A leading tab character usually marks recipe lines in Makefiles;
non-recipe lines must be indented using spaces.
The incorrect tab character doesn't seen to have caused any issues in
this case, but it should be fixed nonetheless, if only for consistency.
The file_contains_line helper function was not testing whether a file
exists or not prior attempting to read from it.
Add this check to circumvent errors on the private WiFi config in
case the hwflags file is missing.
Reported-by: Tom Herbers <freifunk@tomherbers.de>
Tested-by: Tom Herbers <freifunk@tomherbers.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
The relevant entry for the primary MAC location was lost when rebasing
the patch on OpenWrt 21.02.
Fixes commit ded4b8a711 ("rockchip-armv8: add FriendlyARM NanoPi R2S")
Signed-off-by: David Bauer <mail@david-bauer.net>
Configure a radio for HE (802.11ax) operation in case it's supported by
the hardware. This can be the case for 2.4 GHz as well as 5 GHz.
Signed-off-by: David Bauer <mail@david-bauer.net>
In case the limit_ingress or limit_egress options are not present in
gluon's mesh_vpn section the respondd provider compares a string literal
with a NULL pointer, crashing respondd.
Check both pointers prior to comparing them in order to mitigate this
issue.
Suggested-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: David Bauer <mail@david-bauer.net>
This fully abstracts VPN methods, making gluon-mesh-vpn-fastd and
gluon-mesh-vpn-tunneldigger completely self-contained.
Provide a LUA interface for generic interacting with VPN methods in
gluon-mesh-vpn-core and web packages.
This also adds the ability to install tunneldigger and fastd to the same
image, selecting the VPN method based on the selected domain.
Signed-off-by: David Bauer <mail@david-bauer.net>
Simplify the individual form providers by always running reconfigure. This
also commits all UCI packages, so we can remove all tracking of UCI
sections from the wizard code.
Instead of returning a list of packages to commit, the providers just
save their settings directly. Explicit runs of upgrade scripts are
removed, as they are now run by reconfigure.
This add support for a write() method on sections, in addition to the
value and form level write(). write() is only called when the section is
valid and visible. In addition, write() is empty by default, so it can be
overridden more easily.
Before this commit the decision whether a vxlan layer will be
introduced between the lower interface before the interface is
added to batman was inside the proto. Now the decision is moved
to the user of the proto.
Add a package for handling upgrade-scripts speific for the WAN radio
operation.
This way, the config mode interface can be removed seperately from the
core functionality to perform tasks on system upgrade. This can be
useful when the setup-mode is removed entirely for space preservation.
Allow the transmission of IPv6 multicast packets as long as they are not
flooded through the whole mesh.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Set the ifname for the WAN radio (Private WLAN) to wanX, X being the
radio index.
All other radios created by Gluon already have their ifname defined
following this pattern.
Signed-off-by: David Bauer <mail@david-bauer.net>
The rudimentary flash size determination function expects the partition
for the devices firmware to be called "linux" while it is (since quite
some time) "firmware".
Fix this error to display available flash size as well as more useful
error message in case the uploaded firmware image exceeds the flash
space.
Signed-off-by: David Bauer <mail@david-bauer.net>
With batman-adv 2020.4 and the according backports to batman-adv v2019.2
several more bugs were found and fixed regarding the batman-adv
multicast optimizations feature.
Also a "wakeup-call" feature was added to the Linux bridge IGMP/MLD
snooping code in Gluon to work around issues with Android devices.
With batman-adv now at v2019.2, multicast-to-multi-unicasts conversion
is supported, too. Which means that even if there are a few outdated nodes
these and all other recipients will be served multicast packets via unicast,
too, as long as the sum of receiving nodes does not exceed the multicast
fanout setting (default: 16). If is exceeded, then batman-adv will revert
back to broadcast flooding automatically.
Long story short, with all these extra measures in place, let's reenable
the batman-adv multicast optimizations to reduce the layer 2 overhead
and in preparation for multicast applications in the future.
The default is enabled for this feature anyway, so removing the
"batctl multicast_mode 0" overwrite is sufficient.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
End the process after one result in case -l is not given
and destination address is unicast.
Reduces singleshot execution time from timeout seconds to around 150ms.
resolves#2184
This device is a dual 5GHz device. It is recommended to manually change the
radio of the first device to the lower 5GHz channels and the second radio
to the upper 5GHz channels
Fixes respondd on 64bit archs, as gluonutil_get_primary_domain() was
assumed to return int without the prototype.
Fixes: bcf57467dd ("libgluonutil: implement gluonutil_get_primary_domain()")
This adds the OpenWrt label-mac device selection as the most preferred
fallback.
While this is only used on OpenWrt 19.07 for backports, we can also use
the label-mac device when backporting device support. This way, we have
to deal with less device-sepcific code downstream.
Signed-off-by: David Bauer <mail@david-bauer.net>
This switches the used wireless daemons for OWE / SAE to the OpenSSL
flavors. The WolfSSL implementation currently seems to be broken.
THis switch may be reverted at a later point in time when hostapd /
wpa_supplicant implementations for WolfSSL have matured.
Specifications:
* SoC: MT7620A
* RAM: 64 MB DDR
* Flash: 8MB NOR SPI flash
* WiFi: MT7612E (5Ghz) and builtin MT7620A (2.4GHz)
* LAN: 1x100M
The -factory images can be flashed from the device's web
interface or via nmrpflash.
Both devices differ by a additional power outlet for the EX3800.
This patch has been tested on a EX3800 device.
This renames the local_client zone to loc_client, as local_clint exceeds
the maximum zone length allowed for firewall3, which is 11 bytes.
This worked previously due to firewall3 using unsafe string operations.
Now creation of the chain fails (latest OpenWrt master).
This allows running a respondd querier and map server behind a Gluon
node.
For instance at Freifunk Lübeck we now moved the map server
behind a Gluon VM and removed batman-adv and fastd from the
map server VM to reduce the maintenance work.
Increased multicast overhead should be minimal / non existent, as it is
unlikely to accidentally have respondd queriers running behind a Gluon
node.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
The rewrite of the feature handling introduced multiple major bugs. One
of them was caused by the way Lua's logical operators work:
An expression of the form
_'autoupdater' and _'web-advanced'
would return 'web-advanced' rather than the boolean true when _ returned
both strings unchanged (because the features are enabled).
As entries with more than a single feature name in their expressions did
not set no_default, Gluon would then attempt to add gluon-web-advanced to
the package selection, as web-advanced is a "pure" feature.
To fix this, and get rid of the annoying nodefault, separate handling of
"pure" feature and handling of logical expressions into two separate
functions, called feature() and when(). To simplify the feature
definitions, the package list is now passed directly to these functions
rather than in a table with a single field 'packages'.
Fixes: ee5ec5afe5 ("build: rewrite features.sh in Lua")
The new options are CONFIG_GLUON_AUTOUPDATER_BRANCH and
CONFIG_GLUON_AUTOUPDATER_ENABLED and allow to control the default branch
and default enable status separately.
The `or ''` fallback in targets/generic is removed, as GLUON_ENV will
set all variables in GLUON_VARS, making previously non-existing
variables exist with an empty value.
We already have a proper message when the creation of an alias fails
because of a name conflict. Also add a message when the primary filename
of a domain config is already occupied by another domain's alias.
Also add an 'Error:' prefix to the existing message to easier to see.
Reorder scripts so that the mesh_lan interface is accounted for.
Two other firewall upgrade scripts (mesh-babel and l3roamd) are
reordered as well. While there seems to be no hard dependency at the
moment, it makes sense to run the basic setup first, also to avoid
problems with future changes.
Closes: #2090
Fixes: ed094bc68c ("gluon-core: firewall: Allow custom gluon_wired interfaces (#2041)")
This adds the wireless client count for 2.4GHz and 5 GHz radios to the
status page. Previously, only the total client count advertised by
the mesh protocol was visible.
This will hide the outdoor mode setting on compatible devices in case
the defined channels should be preserved.
Otherwise a user might be under the impression their device is compliant
with outdoor operation when in reality it still uses prohibited
channels.
* build: target_config_lib: introduce concat_list helper
* build: rewrite features.sh in Lua
The `features` file is converted to a Lua-based DSL.
A helper function `_` is used in the DSL; this will return the original
string for enabled features, and nil for disabled features. This allows
to use boolean operations on features without making the code too
verbose.
Besides having more readable and robust code, this also fixes the bug
that all files `packages/*/features` were evaluated instead of only
using the feature definitions of currently active feeds.
* build: add luacheck support for package/features
