This updates the batman-adv OpenWrt package to the current version
provided in the master branch of the openwrt-routing packages
repository:
* e26096a batman-adv: Fix duplicated OGMs on NETDEV_UP
* 1ff00ee batman-adv: upgrade package to latest release 2019.2
Small difference to the original:
* Compat code for batadv_genl_dump_check_consistent()
* Compat code for cfg80211_sinfo_release_content()
* 0001-batman-adv-add-compat-hacks.patch kept
* batctl dependency kept removed
* config related files unchanged
The new config format was not backported yet to keep this patch small
and less invasive.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
The factory firmware omits the JFFS2 end-marker while flashing via
web-interface. Add a 64k padding after the marker fixes this problem.
When the end-marker is not present, OpenWRT won't save the overlayfs
after initial flash.
This always pulls in the batman-adv compat 15 kernel module. However,
batctl works just as well with batman-adv-legacy (compat 14).
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
If no mcast_rate is set for the wifi-iface then there is no rate_idx (0)
set for the bss. This breaks for example 5GHz meshpoint interfaces because
0 maps to a CCK rate (11Mbit/s).
It must also be avoided that the ath10k-ct internal state for the rates is
not synced with the mac80211 rates state. Otherwise, the user specified
rate (e.g. a wifi-iface mcast_rate for a meshpoint interface) will only be
set on startup. And a short while after that, ath10k-ct specific code in
ath10k_check_apply_special_rates is missing a valid rate in its own
structures and is then recalculating a new default rate. This default rate
is in most situations not the requested rate.
Fixes: a399b60735 ("ath10k/ath10k-ct: support multicast and management rate control")
Drivers with software rate control can directly use the selected multicast
rate for multicast/broadcast frames and the minimal basic rate for
management frames. But drivers with offloaded rate control algorithms must
be informed about such upper layer decisions to configure the
hardware/firmware.
A new BSS_CHANGED_MCAST_RATE is introduced in mac80211 to automatically
inform all drivers. ath10k can detect this event and forward it via WMI to
the driver. The already existing BSS_CHANGED_BASIC_RATES can be used to
select the management rate.
Without the WMI commands, a low rate (not necessarily one from the basic
rates) is used for bcast/mcast/management frames. This means that the
/etc/config/wireless settings basic_rate and mcast_rate would have no
effect on the rates selected by this driver for the mentioned frames.
This backports the TP-Link Archer C50 v4.
We are dropping the following upstream commits. They add support for the
TP-Link recovery-flag which enabled the web-recovery. As they are not
needed for the router to work, we drop them for now.
28cd2ca base-files: sysupgrade: support additional mtd options
1e06482 mtd: add logic for TP-Link ramips recovery magic
6e16dd1234 mt76: update to the latest version
76037756d0 kernel: bump 4.14 to 4.14.94
455bfd1065 kernel: bump 4.9 to 4.9.151
fafd7691e6 opkg: update to latest Git head
e789bd2243 opkg: drop argument from check_signature in opkg.conf
3603c2321d ramips: mt7621: fix 5GHz WiFi LED on ZBT WG3526
7f98cd8d50 odhcpd: fix onlink IA check (FS#2060)
abd0f7995e kmod-sched-cake: bump to latest cake
Compile-tested: ar71xx-{tiny,generic}, ramips-mt7621, x86-64
6f74e269c8 kernel: bump 4.14 to 4.14.87
b2f243394e kernel: bump 4.9 to 4.9.144
2213b20aee kernel: bump 4.14 to 4.14.86
bcd7644007 kernel: bump 4.9 to 4.9.143
d5afaa4114 openvpn: re-add option comp_lzo
629073e86d rpcd: update to latest Git head
1cd945ea22 ramips: fix leds on GL.iNet GL-MT300N-V2
fbadfecbb5 ipq40xx: fix openmesh sysupgrade with tar content out of order
06a20afb34 rules.mk: fix syntax error
d40e90986c rules.mk: add INSTALL_SUID macro
d40de11d1b base-files: fix prerm return value, align with postinst code
cc8e875039 sdk: find kernel modules when KDIR is a symlink
a8b292afe6 uhttpd: update to latest Git head
7a8b75375c uhttpd: support multiple Lua prefixes
fede6df09e uhttpd: update to latest Git head
9671a2d2c8 apm821xx: MBL: load kernel/dtb from SATA 0:1 first
26ebcc88e3 apm821xx: wndr4700: restore sd-card media detection
5337319bdf uclient: update to latest Git head
Compile-tested: ar71xx, ipq40xx, x86-64
Runtime-tested: ar71xx
ath10k-ct uses a rather high number of buffers to communicate with the
QCA/Candelatech firmware. Especially the HTC (host-target-communication)
and HTT (host-target-transport) can take up a lot of memory when data is
transferred over a ath10k wifi link.
Even a 256MB device with three radios can go OOM (while sending to three
devices using UDP unicast/multicast packets) with the default buffer
limits. Unfortunately, this also reduced the maximum 5GHz throughput on an
IPQ40xx device from 494/432 Mbit/s for TCP transfers (download/upload) to
438/343 Mbit/s. These throughput values should still be good enough for a
Freifunk installation. And these changes are already used by ath10k in
OpenWrt 18.06.
bc7abe8729f3 include/kernel-build.mk: fix kernel rebuild on backport patch changes
c99c70e05303 kernel: backport page fragment API changes from 4.10+ to 4.9
This commit makes use of the Power-LED as Diag-LED, allowing the LED to
work as a status indicator for config-mode.
Signed-off-by: David Bauer <mail@david-bauer.net>
b6a1f43075f9 base-files: fix UCI config parsing and callback handling
6734f32d91cd mtd: add build hack to reintroduce shared mtd for older releases
aaac9e82aa60 mtd: mark as nonshared to fix FS#484
0fee4906d5c0 ustream-ssl: update to latest git HEAD
f34a0756fd94 ustream-ssl: update to latest git HEAD
98b9d8a3d3fd mbedtls: Activate the session cache
88ba88e5adc4 mbedtls: update mbedtls to version 2.7.3
Most of the implementations behind cfg80211_get_station will not initialize
sinfo to zero before manipulating it. For example, the member "filled",
which indicates the filled in parts of this struct, is often only modified
by enabling certain bits in the bitfield while keeping the remaining bits
in their original state. A caller without a preinitialized sinfo.filled can
then no longer decide which parts of sinfo were filled in by
cfg80211_get_station (or actually the underlying implementations).
cfg80211_get_station must therefore take care that sinfo is initialized to
zero. Otherwise, the caller may tries to read information which was not
filled in and which must therefore also be considered uninitialized. In
batadv_v_elp_get_throughput's case, an invalid "random" expected throughput
may be stored for this neighbor and thus the B.A.T.M.A.N V algorithm may
switch to non-optimal neighbors for certain destinations.
A reference to the best gateway is taken when the list of gateways in the
mesh is sent via netlink. This is necessary to check whether the currently
dumped entry is the currently selected gateway or not. This information is
then transferred as flag BATADV_ATTR_FLAG_BEST.
After the comparison of the current entry is done,
batadv_*_gw_dump_entry() has to decrease the reference counter again.
Otherwise the reference will be held and thus prevents a proper shutdown of
the batman-adv interfaces (and some of the interfaces enslaved in it).
Fixes: 899235a4a637 ("Merge pull request #241 from ecsv/batman-adv-2016.4-maint-2016-10-29")
Reported-by: Andreas Ziegler <dev@andreas-ziegler.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
This commit adds support for the AVM Fritz!Box 4020 WiFi-router.
SoC: Qualcomm Atheros QCA9561 (Dragonfly) 750MHz
RAM: Winbond W971GG6KB-25
FLASH: Macronix MX25L12835F
WiFi: QCA9561 b/g/n 3x3 450Mbit/s
USB: 1x USB 2.0
IN: WPS button, WiFi button
OUT: Power LED green, Internet LED green, WLAN LED green,
LAN LED green, INFO LED green, INFO LED red
UART: Header Next to Black metal shield
Pinout is 3.3V - RX - TX - GND (Square Pad is 3.3V)
The Serial setting is 115200-8-N-1.
Tested and working:
- Ethernet (LAN + WAN)
- WiFi (correct MAC)
- Installation via EVA bootloader
- OpenWRT sysupgrade
- Buttons
- LEDs
Not working:
- USB port
Installation via EVA:
In the first seconds after Power is connected, the bootloader will
listen for FTP connections on 169.254.157.1 (Might also be 192.168.178.1). Firmware can be uploaded
like following:
ftp> quote USER adam2
ftp> quote PASS adam2
ftp> binary
ftp> debug
ftp> passive
ftp> quote MEDIA FLSH
ftp> put openwrt-sysupgrade.bin mtd1
Note that this procedure might take up to two minutes. After transfer is
complete you need to powercycle the device to boot OpenWRT.
Signed-off-by: David Bauer <mail@david-bauer.net>
999bb66b20b0 kernel: add missing in6_dev_put_clear call to an ipv6 network patch
81573ea25924 kernel: bump kernel 4.4 to 4.4.129 for 17.01
afa887388766 gcc: gcc 6.3.0 fix comparison between pointer and integer
efb6ca189641 base-files: /lib/functions.sh: ignore errors in insert_modules
b5ba01a0d3f6 fstools: update to latest lede-17.01 branch
a9b607740273 kernel: bump kernel 4.4 to 4.4.126 for 17.01
09d95e44fc3d mbedtls: change libmbedcrypto.so soversion back to 0
4673a0bffc89 kernel: mtd: bcm47xxpart: improve handling TRX partition size
Also switch to the upstreamed version of "kernel: disable accept_ra by
default".
