Device information can be found at:
http://www.8devices.com/products/carambola-2https://wiki.openwrt.org/toh/8devices/carambola2
I only did some minimal testing of gluon on the carambola 2 development
board:
- Config mode works
- Connects to Wifi Mesh
- Allows clients to connect
Notably, autoupgrade has not yet been tested.
Change to 010-primary-mac is necessary as the mac address printed
on the sticker is the one of eth0, not the wifi mac.
link "packages" instead of "community repositories"
add link for rejected features to bottom link list
link "#gluon" to webirc
link the mentioned commit 2a93c58
OpenWRT now supports the CISCO Meraki enterprise class routers
MR12, MR16, MR62 and MR66. The fabric firmware demands the yearly
renewal of a support license.
This firmware was successfully tested by @Garunda for the MR62 (and
the MR12 with it for which this is an alias). The initial firmware
pre OpenWRT adoption was prepared and adapted for Gluon by @tcatm.
The confirmation of the functionality of the image for the MR66
(and the aliased MR16 with it) is still pending.
The devices are of strategic interest to the Freifunk community as
they are making a rock-solid impression. However, these come with
fairly hefty annual license. The Freifunk may offer an escape route
for those who had signed up and want to keep their investment into the
similarly expensive hardware. Used evices sell for $60 on eBay/Amazon
in the US. Here in the old world it is all >300 €, still.
Credits go to @Garunda for testing, to @tcatm for finding the
OpenWRT patch prior to its adoption and preparing the initial Gluon
adaptation, to @smoe for the update once that patch had arrived in
OpenWRT, and to @NeoRaider for his review and advice to use
GluonModelAlias for MR62 and MR66 to point to MR12 and MR16,
respectively.
Original commit message:
MIPS: ath79: make bootconsole wait for both THRE and TEMT
This makes the ath79 bootconsole behave the same way as the generic 8250
bootconsole.
Also waiting for TEMT (transmit buffer is empty) instead of just THRE
(transmit buffer is not full) ensures that all characters have been
transmitted before the real serial driver starts reconfiguring the serial
controller (which would sometimes result in garbage being transmitted.)
This change does not cause a visible performance loss.
In addition, this seems to fix a hang observed in certain configurations on
many AR7xxx/AR9xxx SoCs during autoconfig of the real serial driver.
A more complete follow-up patch will disable 8250 autoconfig for ath79
altogether (the serial controller is detected as a 16550A, which is not
fully compatible with the ath79 serial, and the autoconfig may lead to
undefined behavior on ath79.)
Patch tested on v2016.1.x branch with Freifunk Magdeburg firmware on
Debian Jessie amd64 Xen host. See the same patch in our gluon fork here:
https://github.com/FreifunkMD/gluon/blob/fix-sysupgrade-xen/patches/openwrt/0058-x86-fix-platform_export_bootpart-for-Xen-virtual-disks.patch
Sysupgrade was tested successfully by manually making the change before
upgrading in the filesystem of the running node and upgrading to the
fixed FFMD experimental build in config mode via expert settings in
webgui.
Patch also submitted to OpenWRT trunk already.
Signed-off-by: Alexander Dahl <alex@netz39.de>
The Hornet UB is sold at least in the varieties. Without case it is a Hornet UB, with case and without connected USB port it is called AP121. If the USB port is present this device is called AP121U.
We have a AP121U in our mesh http://meshviewer.chemnitz.freifunk.net/#!v:m;n:00c0ca6efffa
