This device is a dual 5GHz device. It is recommended to manually change the
radio of the first device to the lower 5GHz channels and the second radio
to the upper 5GHz channels.
Add support for IBSS meshing. Leave target marked as BROKEN for IBSS
as stability is unknown and WiFi LEDs are not working.
Functionality was tested in the network of Freifunk Frankfurt with other
ipq40xx and ar71xx devices.
Support is marked as broken because this device is sold in two variants,
one with 64M RAM and another with 128M. As of now 64M is not enough
for ath10k with 5GHz enabled.
As there is no indication known which variant one will get better mark
it as broken.
Signed-off-by: Christoph Krapp <achterin@googlemail.com>
Adds support for Alfa AP121F USB powered travel router (looks like an USB ethernet adapter).
There is no factory image, but only a sysupgrade file for this router which can be installed using the inbuilt UBoot web interface.
Configure your PC with IP address 192.168.1.2 and connect the router using its RJ45 port. Hold the reset button while powering the device until all LEDs have flashed 3 times simultaneously. You can now access the fallback web interface using a web browser at http://192.168.1.1 and flash the sysupgrade file.
This commit adds support for the AVM Fritz!Box 4020 WiFi-router.
SoC: Qualcomm Atheros QCA9561 (Dragonfly) 750MHz
RAM: Winbond W971GG6KB-25
FLASH: Macronix MX25L12835F
WiFi: QCA9561 b/g/n 3x3 450Mbit/s
USB: 1x USB 2.0
IN: WPS button, WiFi button
OUT: Power LED green, Internet LED green, WLAN LED green,
LAN LED green, INFO LED green, INFO LED red
UART: Header Next to Black metal shield
Pinout is 3.3V - RX - TX - GND (Square Pad is 3.3V)
The Serial setting is 115200-8-N-1.
Tested and working:
- Ethernet (LAN + WAN)
- WiFi (correct MAC)
- Installation via EVA bootloader
- OpenWRT sysupgrade
- Buttons
- LEDs
Not working:
- USB port
Installation via EVA:
In the first seconds after Power is connected, the bootloader will
listen for FTP connections on 169.254.157.1 (Might also be 192.168.178.1). Firmware can be uploaded
like following:
ftp> quote USER adam2
ftp> quote PASS adam2
ftp> binary
ftp> debug
ftp> passive
ftp> quote MEDIA FLSH
ftp> put openwrt-sysupgrade.bin mtd1
Note that this procedure might take up to two minutes. After transfer is
complete you need to powercycle the device to boot OpenWRT.
Signed-off-by: David Bauer <mail@david-bauer.net>
ar71xx-generic and -tiny benefit most from the optimized kernel, as they
contain all devices with 32MB RAM. We enable CONFIG_GLUON_SPECIALIZE_KERNEL
for all targets using the mips24_kc architecture so packages shared between
targets don't need to be rebuild all the time.
b1205a9211 ar71xx: /lib/ar71xx.sh: add model detection for TP-Link TL-WR810N
fbeae9d891 iptables: make kmod-ipt-debug part of default ALL build
6ea9a702c5 iptables: Fix target TRACE issue
00fa1e4108 curl: fix libcurl/mbedtls async interface
d5278cc48b kernel: bump 4.4 to 4.4.112 for 17.01
2ae0741f3b dnsmasq: backport validation fix in dnssec security fix
58d60bd283 dnsmasq: backport dnssec security fix for 17.01
d626aa005b mountd: bump to git HEAD version
f0336975be kernel: bump 4.4 to 4.4.111 for 17.01
fb6f21c657 kmod-sched-cake: bump to latest cake bake for 17.01
2e8a3bb35f ar71xx: Netgear WNR2000v4: do not include USB packages [17.01]
3fa86282fa build: fix restoring /etc/opkg with PER_DEVICE_ROOTFS
987a7e3175 ramips: fix lenovo newifi-y1 switch and LED config
dbb5ffaed5 ramips: firewrt: indicate boot status via LED
A bug in batman-adv can lead to a large amount of management traffic being
exchanged between nodes when the multicast optimizations are enabled,
effectively making the mesh unusable. It's safer to disable the feature
for now, until we have a real fix.
sha512sum doesn't add much code that is not also used by sha256sum, but the
change of the configuration hides the segfault issue described in:
https://bugs.lede-project.org/index.php?do=details&task_id=822
While the issue only seemed to affect dhcpv6.script, it would clutter /tmp
with coredumps, eventually leading to OOM.
Fixes#1084
Hardware is very similar to Archer C5v1 and C7v2.
Tested factory install and autoupdater.
IBSS Mesh on 2.4 and 5 GHz is working fine.
The only Ethernet Port is used for config mode and afterwards handled
as WAN Port.
The size of the factory images is limited to 4MB, which caused build
failures when many additional packages were included.
Rather than moving the device to ar71xx-tiny, we ignore the factory images
and just build the sysupgrade. This way, the whole flash is usable for
Gluon.
This means that installing Gluon on these devices will now require to flash
a plain LEDE image first, and then upgrading using the Gluon sysupgrade
image.
Fixes#1020
