TP-Link RE200 v2 is a wireless range extender with Ethernet and 2.4G and 5G
WiFi with internal antennas. It's based on MediaTek MT7628AN+MT7610EN.
Specifications
--------------
- MediaTek MT7628AN (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 1T1R 5 GHz
- 1x 10/100 Mbps Ethernet
- UART header on PCB (57600 8n1)
- 8x LED (GPIO-controlled), 2x button
There are 2.4G and 5G LEDs in red and green which are controlled
separately.
MAC addresses
-------------
The MAC address assignment matches stock firmware, i.e.:
LAN : *:0D
2.4G: *:0E
5G : *:0F
Installation
------------
Web Interface
-------------
It is possible to upgrade to OpenWrt via the web interface. Simply flash
the -factory.bin from OEM. In contrast to a stock firmware, this will not
overwrite U-Boot.
VoCores aren't exactly useful mesh nodes except for experimentation.
They certainly aren't worth maintaining a whole target, in particular
one that has a WLAN driver not used by any other target.
Specifications:
- CPU: MediaTek MT7628AN (580MHz)
- Flash: 16MB
- RAM: 64MB DDR2
- 2.4 GHz: IEEE 802.11b/g/n with Integrated LNA and PA
- Antennas: 4x external single band antennas
- WAN: 1x 10/100M
- LAN: 2x 10/100M
- LEDs: 2x yellow/blue. Programmable (labelled as power on case)
- Non-programmable (shows WAN activity)
- Button: Reset
How to install:
1- Use OpenWRTInvasion to gain telnet and ftp access.
2- Push openwrt firmware to /tmp/ using ftp.
3- Connect to router using telnet. (IP: 192.168.31.1 -
Username: root - No password)
4- Use command "mtd -r write /tmp/firmware.bin OS1" to flash into
the router..
5- It takes around 2 minutes. After that router will restart itself
to OpenWrt.
Specifications:
- SoC: MediaTek MT7621
- Flash: 16 MiB NOR SPI
- RAM: 128 MiB DDR3
- Ethernet: 3x 10/100/1000 Mbps (switched, 2xLAN + WAN)
- WIFI0: MT7603E 2.4GHz 802.11b/g/n
- WIFI1: MT7612E 5GHz 802.11ac
- Antennas: 4x external (2 per radio), non-detachable
- LEDs: Programmable "power" LED (two-coloured, yellow/blue)
Non-programmable "internet" LED (shows WAN activity)
- Buttons: Reset
Installation:
Bootloader won't accept any serial input unless "boot_wait" u-boot
environment variable is changed to "on".
Vendor firmware won't accept any serial input until "uart_en" is
set to "1".
Using the https://github.com/acecilia/OpenWRTInvasion exploit you
can gain access to shell to enable these options:
To enable uart keyboard actions - 'nvram set uart_en=1'
To make uboot delay boot work - 'nvram set boot_wait=on'
Set boot delay to 5 - 'nvram set bootdelay=5'
Then run 'nvram commit' to make the changes permanent.
Once in the shell (following the OpenWRTInvasion instructions) you
can then run the following to flash OpenWrt and then reboot:
'cd /tmp; curl https://downloads.openwrt.org/...-sysupgrade.bin
--output firmware.bin; mtd -e OS1 -r write firmware.bin OS1'
This device is a dual 5GHz device. It is recommended to manually change the
radio of the first device to the lower 5GHz channels and the second radio
to the upper 5GHz channels
* ar71xx-generic: only create manifest alias for Rocket M5
This follow up the discussion done in #2070 by not creating a symlink
for the Rocket M5. Images for the Rocket M2 can still be flashed on a
Rocket M5.
This change will prevent the Rocket M5 from appearing in Firmware
selectors. Existing devices will still receive updates, as the device
name is still referenced for the device name expected by the M5.
Closes#2070
* docs: remove Rocket M5 from supported devices
This change stores a Kernel with Debug-Symbols for the current
architecture in a new output directory '<outputdir>/debug'.
This allows a developer or operator of a network to store the kernel
along with the actual images. In case of a kernel oops the debug
information can be used with the script
'scripts/decode_stacktrace.sh' in the kernel source tree to get the
names to the symbols of the stack trace.
OpenWRT already provides the CONFIG_COLLECT_KERNEL_DEBUG -option that
creates a kernel with debug-symbols in the OpenWRT output directory.
This change enables this option and copies the generated kernel to the
gluon output directory.
Signed-off-by: Chrissi^ <chris@tinyhost.de>
This adds support for the beacon interval to be set on a per-band base.
This has the potential to reduce the amount of airtime used up for
sending beacon frames.
The 'preserve' flag can be used to mark a peer so it is not removed or
modified on upgrades. In addition, groups containing preserved peers are
not removed.
Fixes: #557
This device has broken Ethernet on both ports.
Remove support for those devices. for now, as there was no feedback from
the original author.
Closes#1943
The kernel partition on these devices is too small for the
OpenWrt 19.07 kernel. It is also located after the rootfs, so
we cannot grow it further.
Therefore mark these devices as deprecated now.
This adds documentation for the gluon-mesh-batman-adv package and
elaborates on its build and configuration options, as well as
the implemented multicast architecture.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
This new build flag is mandatory for now (it may default to 0 in a future
Gluon version). It may be set to the following values:
* 0 - Do not build any images for deprecated devices.
* upgrade - Only build sysupgrade images for deprecated devices.
* full - Build both sysupgrade and factory images for deprecated devices.
"Other" images are handled like factory images, as they are also used for
the initial installation of Gluon on a device.
Add the `wifi5.outdoor_chanlist` site configuration that
allows specifying an outdoor channel range that can be
switched to for regulatory compliance.
Upon enabling the outdoor option the device will
- configure the `outdoor_chanlist` on all 5 GHz radios
- which may enable DFS/TPC, based on the regulatory domain
- disable ibss/mesh on the 5 GHz radio, as DFS *will*
break mesh connections
- allow for htmode reconfiguration on 5 GHz radios
The outdoor option can be toggled from
- Advanced Settings
- W-LAN
- Outdoor Installation
The `preserve_channel` flag overrules the outdoor channel
selection.
Before 7827f89, mandatory hostname field in config mode was
pre-filled with the default hostname.
This commit adds the config_mode.hostname.prefill option for
controlling the default value.
gluon-config-mode-geo-location-osm extends the
gluon-config-mode-geo-location with a location picker based on
OpenStreetMaps.
Based-on-patch-by: Jan-Tarek Butt <tarek@ring0.de>
As already done with other config mode texts, the altitude field now has
default texts that are used when they are not set in the site i18n files.
The altitude-help text has been removed from site i18n; instead, the
geo-location-help text now overrides the whole section description
including the part that mentions the altitude.
* do not allow to obligatorily require contact information
* add remark that the data is provided voluntarily
* mention how to delete the data
* be very clear about the fact that the data being entered is public and
can be downloaded and processed by anyone.
In multidomain setups, VXLAN is enabled by default, but can be disabled in
domain configs using the mesh/vxlan option. In single domain setups, the
mesh/vxlan option is mandatory.
The UCI option for legacy mode is removed.
Fixes#1364
This setting allows to enforce manually setting a hostname.
In the initial configuration, the hostname field is now left empty; when
setting the hostname is not enforced, the default hostname is shown as the
field placeholder.
Fixes#1139
We must ensure that each node becomes IGMP/MLD querier for its local
clients; having only a single querier for the whole mesh is generally
unreliable, leading to frequent "IGMP/MLD querier appeared/disappeared"
messages from batman-adv and unreliable snooping.
In smaller meshes it might be interesting only segment querier domains, but
allow membership reports to pass through the mesh, in order to support
snooping switches outside the mesh without special configuration. A
site.conf switch is provided to control this behaviour.
Fixes#1320
This is currently only implemented in the gluon-mesh-vpn-fastd
package.
Advertising the public key may be deemed problematic when
your threat-model involves protecting the nodes privacy
from tunnel traffic correlation by onlink observers.
It can be enabled by setting site.mesh_vpn.fastd.pubkey_privacy
to `false`.
Adding the fact that GLUON_RELEASE is needed with 'make manifest'
if it is used with 'make'.
This fact was mentioned in the v2017.1 release notes but is not (clearly)
mentioned inside other parts of the documentation.
Signed-off-by: Chrissi^ <chris@tinyhost.de>
[Matthias Schiffer: minor rewording]
To reduce the number of packages that need to be listed in
GLUON_SITE_PACKAGES, this adds a new variable GLUON_FEATURES. Sets of
packages are enabled automatically based on the combination of listed
feature flags.
Site-specified package feeds can provide their own feature flag
definitions.
