Speedy join only works when the received packet is either broadcast or an
4addr unicast packet. Thus packets converted from broadcast to unicast via
the gateway handling code have to be converted to 4addr packets to allow
the receiving gateway server to add the sender address as temporary entry
to the translation table.
Not doing it will make the batman-adv gateway server drop the DHCP response
in many situations because it doesn't yet have the TT entry for the
destination of the DHCP response.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The new MR1750v2 device support is only available in LEDE master. The
relevant patches have to backported to add support for them in Gluon
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
The new OM2P-HSv3 device support is only available in LEDE master. The
relevant patches have to backported to add support for them in Gluon
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
This patchset enables the RX LNA for the CPE210/510, improving RX by about
20dB. The profiles for CPE210 and CPE510 is split into two images, so the
CPE510 can use the correct ART offset, improving the TX power by 10dB.
Fixes#796
Most doubles that are delivered via respondd have limited input
precision, but are converted with up to 17 digits of precision. That can
cause ugly blowups like 0.2800000000000001 in the output, which is
avoided by specifying better format strings (like "%.2f" in most cases).
The new ath9k/ath10k based devices are only available in OpenWrt trunk. The
relevant patches have to backported to add support for them in Gluon
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
The workaround to generate sysupgrade images for OpenMesh devices in gluon
is replaced in LEDE/OpenWrt by a special patch. It is therefore better to
drop the workaround and use the upstream version.
Reported-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Original commit message:
MIPS: ath79: make bootconsole wait for both THRE and TEMT
This makes the ath79 bootconsole behave the same way as the generic 8250
bootconsole.
Also waiting for TEMT (transmit buffer is empty) instead of just THRE
(transmit buffer is not full) ensures that all characters have been
transmitted before the real serial driver starts reconfiguring the serial
controller (which would sometimes result in garbage being transmitted.)
This change does not cause a visible performance loss.
In addition, this seems to fix a hang observed in certain configurations on
many AR7xxx/AR9xxx SoCs during autoconfig of the real serial driver.
A more complete follow-up patch will disable 8250 autoconfig for ath79
altogether (the serial controller is detected as a 16550A, which is not
fully compatible with the ath79 serial, and the autoconfig may lead to
undefined behavior on ath79.)
Patch tested on v2016.1.x branch with Freifunk Magdeburg firmware on
Debian Jessie amd64 Xen host. See the same patch in our gluon fork here:
https://github.com/FreifunkMD/gluon/blob/fix-sysupgrade-xen/patches/openwrt/0058-x86-fix-platform_export_bootpart-for-Xen-virtual-disks.patch
Sysupgrade was tested successfully by manually making the change before
upgrading in the filesystem of the running node and upgrading to the
fixed FFMD experimental build in config mode via expert settings in
webgui.
Patch also submitted to OpenWRT trunk already.
Signed-off-by: Alexander Dahl <alex@netz39.de>
