62feabecd8 kernel: bump 4.14 to 4.14.99
9fb3710a8b kernel: bump 4.9 to 4.9.156
e5ace80759 mt76: update to the latest version
fbb2186fbd kernel: bump 4.14 to 4.14.98
72870cc108 kernel: bump 4.9 to 4.9.155
19a6c4b2b3 mac80211: brcmfmac: fix a possible NULL pointer dereference
d997712c71 ath9k: register GPIO chip for OF targets
Compile-tested: ipq40xx, ramips-mt7621
Runtime-tested: none
This reverts commit b92e404437.
Committing in this case is unnecessary as that job is already handled by 998-commit
which is in a superior position to commit, as it is run after all relevant changes to
the configuration have been made.
Gluon has multiple ways to obtain unique MAC-addresses. They are either
provided by the WiFi driver or derived from the primary MAC-address.
Quoting the same file:
> It's necessary that the first 45 bits of the MAC address don't
> vary on a single hardware interface, since some chips are using
> a hardware MAC filter. (e.g 'rt305x')
This currently fails in case the rt35xx based chips mac address differs
from the primary MAC. In this case, the MAC address for the client0 radio
(vif 1) comes from the WiFi driver. As there is only a single
MAC-address provided by '/sys/class/ieee80211/phyX/addresses' but the
MAC-address for mesh 0 (vif 2) is derived from the Node-ID, resulting in
different first 45 bits. The WiFi won't come up altogether in this case.
This commit verifies at least 4 MAC-Addresses are provided by the WiFi
driver. If this is not the case, all MAC-addresses are derived from the
primary MAC. This way, affected radios are working correctly.
Drivers with software rate control can directly use the selected multicast
rate for multicast/broadcast frames and the minimal basic rate for
management frames. But drivers with offloaded rate control algorithms must
be informed about such upper layer decisions to configure the
hardware/firmware.
A new BSS_CHANGED_MCAST_RATE is introduced in mac80211 to automatically
inform all drivers. ath10k can detect this event and forward it via WMI to
the driver. The already existing BSS_CHANGED_BASIC_RATES can be used to
select the management rate.
Without the WMI commands, a low rate (not necessarily one from the basic
rates) is used for bcast/mcast/management frames. This means that the
/etc/config/wireless settings basic_rate and mcast_rate would have no
effect on the rates selected by this driver for the mentioned frames.
This backports the TP-Link Archer C50 v4.
We are dropping the following upstream commits. They add support for the
TP-Link recovery-flag which enabled the web-recovery. As they are not
needed for the router to work, we drop them for now.
28cd2ca base-files: sysupgrade: support additional mtd options
1e06482 mtd: add logic for TP-Link ramips recovery magic
This allows for smaller firmware images and makes it possible to reset a
device via firstboot command.
Signed-off-by: Matthias Fritzsche <matthias@chemnitz.freifunk.net>
6e16dd1234 mt76: update to the latest version
76037756d0 kernel: bump 4.14 to 4.14.94
455bfd1065 kernel: bump 4.9 to 4.9.151
fafd7691e6 opkg: update to latest Git head
e789bd2243 opkg: drop argument from check_signature in opkg.conf
3603c2321d ramips: mt7621: fix 5GHz WiFi LED on ZBT WG3526
7f98cd8d50 odhcpd: fix onlink IA check (FS#2060)
abd0f7995e kmod-sched-cake: bump to latest cake
Compile-tested: ar71xx-{tiny,generic}, ramips-mt7621, x86-64
This commit removes the broken flag from all devices in the mt76x8
subtarget.
The stability of the mt76 driver for the mt7628 and mt7612 has greatly
improved in the last half-year. It might be still behind ath9k and
ath10k but it is suitable for daily use.
This affects the following devices:
- GL.iNet MT300N v2
- TP-Link Archer C50 v3
- TP-Link TL-WR841 v13
This commit distributes dualband radios evenly on 2.4 GHz and 5GHz with
2.4 GHz being prioritised higher than 5 GHz. This means in case a device
has only a single radio and this radio supports operation in both bands,
it will be set to 2.4 GHz.
Tested-by: Martin Weinelt <martin@darmstadt.freifunk.net>
Signed-off-by: David Bauer <mail@david-bauer.net>
