The GLUON_ATH10K_MESH must be set to 11s or ibss; when it is not set,
ath10k device images won't be built at all. This also allows us to remove
the BROKEN flag for ath10k devices, as the GLUON_ATH10K_MESH variable is
sufficient to avoid ath10k devices if desired.
Fixes#864
The MR1750 and OM5P-AC devices are based on ath9k SoCs and an external
ath10k chip. All devices which are using ath10k should be marked as broken
due to deficits in their IBSS support.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Generate flashable images for the Archer C7 v2 with current stock firmware
again.
To set the region code, the GLUON_REGION variable must be set to "us" or
"eu" in site.mk or as a make argument.
Fixes#860
This patchset enables the RX LNA for the CPE210/510, improving RX by about
20dB. The profiles for CPE210 and CPE510 is split into two images.
The problematic patch switching the CPE510 to the secondary ART is left
out.
I've bought a couple of those devices from Senetic GmbH.
https://www.senetic.de/product/TL-WR842N
They have 16 MB of Flash and 64 MB of RAM. Platform support works fine,
I've also tested a little with Ethernet (since I saw some regressions on
OpenWRT/LEDE with 841v11), no problems.
Therefore, lets remove the broken mark.
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The new MR1750v2 device support is only available in LEDE master. The
relevant patches have to backported to add support for them in Gluon
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
The new OM2P-HSv3 device support is only available in LEDE master. The
relevant patches have to backported to add support for them in Gluon
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
This patchset enables the RX LNA for the CPE210/510, improving RX by about
20dB. The profiles for CPE210 and CPE510 is split into two images, so the
CPE510 can use the correct ART offset, improving the TX power by 10dB.
Fixes#796
The returned name for OpenMesh devices with a an extra vX when calling
lua -e 'print(require("platform_info").get_image_name())'
doesn't contain a dash between the vX and the device name. Thus the image
should also not contain a dash.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
The new ath9k/ath10k based devices are only available in OpenWrt trunk. The
relevant patches have to backported to add support for them in Gluon
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
The workaround to generate sysupgrade images for OpenMesh devices in gluon
is replaced in LEDE/OpenWrt by a special patch. It is therefore better to
drop the workaround and use the upstream version.
Reported-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Device information can be found at:
http://www.8devices.com/products/carambola-2https://wiki.openwrt.org/toh/8devices/carambola2
I only did some minimal testing of gluon on the carambola 2 development
board:
- Config mode works
- Connects to Wifi Mesh
- Allows clients to connect
Notably, autoupgrade has not yet been tested.
Change to 010-primary-mac is necessary as the mac address printed
on the sticker is the one of eth0, not the wifi mac.
OpenWRT now supports the CISCO Meraki enterprise class routers
MR12, MR16, MR62 and MR66. The fabric firmware demands the yearly
renewal of a support license.
This firmware was successfully tested by @Garunda for the MR62 (and
the MR12 with it for which this is an alias). The initial firmware
pre OpenWRT adoption was prepared and adapted for Gluon by @tcatm.
The confirmation of the functionality of the image for the MR66
(and the aliased MR16 with it) is still pending.
The devices are of strategic interest to the Freifunk community as
they are making a rock-solid impression. However, these come with
fairly hefty annual license. The Freifunk may offer an escape route
for those who had signed up and want to keep their investment into the
similarly expensive hardware. Used evices sell for $60 on eBay/Amazon
in the US. Here in the old world it is all >300 €, still.
Credits go to @Garunda for testing, to @tcatm for finding the
OpenWRT patch prior to its adoption and preparing the initial Gluon
adaptation, to @smoe for the update once that patch had arrived in
OpenWRT, and to @NeoRaider for his review and advice to use
GluonModelAlias for MR62 and MR66 to point to MR12 and MR16,
respectively.
