From: Felix Fietkau Date: Tue, 25 Jul 2017 13:32:47 +0200 Subject: ar71xx: add support for TP-LINK Archer C7 v4 TP-Link Archer C7 v4 is a dual-band AC1750 router, based on Qualcomm/Atheros QCA9561+QCA9888. Specification: - 775/650/258 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 3T3R 5 GHz - 5x 10/100/1000 Mbps Ethernet - 7x LED, 2x button - UART header on PCB Flash instruction: 1. Upload lede-ar71xx-generic-archer-c7-v4-squashfs-factory.bin via Web interface Flash instruction using TFTP recovery: 1. Set PC to fixed ip address 192.168.0.66 2. Download lede-ar71xx-generic-archer-c7-v4-squashfs-factory.bin and rename it to ArcherC7v4_tp_recovery.bin 3. Start a tftp server with the file tp_recovery.bin in its root directory 4. Turn off the router 5. Press and hold Reset button 6. Turn on router with the reset button pressed and wait ~15 seconds 7. Release the reset button and after a short time the firmware should be transferred from the tftp server 8. Wait ~30 second to complete recovery. Flash instruction under U-Boot, using UART: 1. tftp 0x81000000 lede-ar71xx-...-sysupgrade.bin 2. erase 0x9f040000 +$filesize 3. cp.b $fileaddr 0x9f040000 $filesize 4. reset Signed-off-by: Felix Fietkau diff --git a/target/linux/ar71xx/base-files/etc/board.d/01_leds b/target/linux/ar71xx/base-files/etc/board.d/01_leds index e67b5e38561e841b88e486341950c52e1d454322..44b1c2837e8392596eed14b4bc0d761042109715 100755 --- a/target/linux/ar71xx/base-files/etc/board.d/01_leds +++ b/target/linux/ar71xx/base-files/etc/board.d/01_leds @@ -53,7 +53,8 @@ ap121f) ucidef_set_led_netdev "lan" "LAN" "$board:green:lan" "eth0" ucidef_set_led_wlan "wlan" "WLAN" "$board:green:wlan" "phy0tpt" ;; -archer-c25-v1) +archer-c25-v1|\ +archer-c7-v4) ucidef_set_led_netdev "wan" "WAN" "$board:green:wan" "eth0" ucidef_set_led_wlan "wlan" "WLAN" "$board:green:wlan2g" "phy1tpt" ucidef_set_led_wlan "wlan5g" "WLAN5G" "$board:green:wlan5g" "phy0tpt" @@ -61,6 +62,12 @@ archer-c25-v1) ucidef_set_led_switch "lan2" "LAN2" "$board:green:lan2" "switch0" "0x08" ucidef_set_led_switch "lan3" "LAN3" "$board:green:lan3" "switch0" "0x04" ucidef_set_led_switch "lan4" "LAN4" "$board:green:lan4" "switch0" "0x02" + case "$board" in + archer-c7-v4) + ucidef_set_led_usbdev "usb1" "USB1" "$board:green:usb1" "1-1" + ucidef_set_led_usbdev "usb2" "USB2" "$board:green:usb2" "2-1" + ;; + esac ;; arduino-yun) ucidef_set_led_wlan "wlan" "WLAN" "arduino:blue:wlan" "phy0tpt" diff --git a/target/linux/ar71xx/base-files/etc/board.d/02_network b/target/linux/ar71xx/base-files/etc/board.d/02_network index 454abe6a5005621967dd96e0282e7bce2a0b127e..86ac949bca12561536ce2c8adb190eb004c162e4 100755 --- a/target/linux/ar71xx/base-files/etc/board.d/02_network +++ b/target/linux/ar71xx/base-files/etc/board.d/02_network @@ -386,6 +386,7 @@ ar71xx_setup_interfaces() ucidef_set_interface_wan "eth0" ucidef_set_interface_raw "wlan" "wlan0" "dhcp" ;; + archer-c7-v4|\ tl-wdr4300|\ tl-wr1041n-v2) ucidef_add_switch "switch0" \ diff --git a/target/linux/ar71xx/base-files/etc/diag.sh b/target/linux/ar71xx/base-files/etc/diag.sh index 61db387c9ecefd7090c25a5f5d75fdbf65a44d65..97372bed0ea2fadfab10f22916a1e0d6a9c65725 100644 --- a/target/linux/ar71xx/base-files/etc/diag.sh +++ b/target/linux/ar71xx/base-files/etc/diag.sh @@ -51,6 +51,7 @@ get_status_led() { status_led="ap135:green:status" ;; archer-c25-v1|\ + archer-c7-v4|\ mr12|\ mr16|\ nbg6616|\ diff --git a/target/linux/ar71xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ar71xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index 68f90de802ddd18e09a1da39c0d56292eea9489c..96b8f6b9a4bdd6a1609a819e72ade315bccfb3c0 100644 --- a/target/linux/ar71xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ar71xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -92,6 +92,7 @@ case "$FIRMWARE" in ath10kcal_extract "art" 20480 2116 ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) -2) ;; + archer-c7-v4|\ archer-c25-v1|\ tl-wdr6500-v2) ath10kcal_extract "art" 20480 2116 diff --git a/target/linux/ar71xx/base-files/lib/ar71xx.sh b/target/linux/ar71xx/base-files/lib/ar71xx.sh index 8f8158bac8a28db4f4f15ce5c37f48a21084dc03..c32894d95b6b09b4b8b59ba64057c23e71b9f656 100755 --- a/target/linux/ar71xx/base-files/lib/ar71xx.sh +++ b/target/linux/ar71xx/base-files/lib/ar71xx.sh @@ -469,6 +469,9 @@ ar71xx_board_detect() { *"Archer C5") name="archer-c5" ;; + *"Archer C7 v4") + name="archer-c7-v4" + ;; *"Archer C7") name="archer-c7" ;; diff --git a/target/linux/ar71xx/base-files/lib/upgrade/platform.sh b/target/linux/ar71xx/base-files/lib/upgrade/platform.sh index 774e3c8964ef724d1efbae56434aeaa9f1c298a4..d6650e7719d268e1a500638b7eda2e15b9251aea 100755 --- a/target/linux/ar71xx/base-files/lib/upgrade/platform.sh +++ b/target/linux/ar71xx/base-files/lib/upgrade/platform.sh @@ -215,6 +215,7 @@ platform_check_image() { ap132|\ ap90q|\ archer-c25-v1|\ + archer-c7-v4|\ bullet-m|\ c-55|\ carambola2|\ diff --git a/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt b/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt index 7ad5419f51ec9909d8b59f33178221a7d81ec184..0a25294c40b5e2d3be825554ec7246a50b9c029b 100644 --- a/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt +++ b/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt @@ -1247,6 +1247,7 @@ config ATH79_MACH_ARCHER_C25_V1 config ATH79_MACH_ARCHER_C7 bool "TP-LINK Archer C5/C7/TL-WDR4900 v2 board support" select SOC_QCA955X + select SOC_QCA956X select ATH79_DEV_AP9X_PCI if PCI select ATH79_DEV_ETH select ATH79_DEV_GPIO_BUTTONS diff --git a/target/linux/ar71xx/files/arch/mips/ath79/Makefile b/target/linux/ar71xx/files/arch/mips/ath79/Makefile index 3365a43ce16fc77b3212b39b92081efe678e8803..a0c73550eb0d5bf07ee731171be9e5ef9ff073e7 100644 --- a/target/linux/ar71xx/files/arch/mips/ath79/Makefile +++ b/target/linux/ar71xx/files/arch/mips/ath79/Makefile @@ -58,6 +58,7 @@ obj-$(CONFIG_ATH79_MACH_AP90Q) += mach-ap90q.o obj-$(CONFIG_ATH79_MACH_AP96) += mach-ap96.o obj-$(CONFIG_ATH79_MACH_ARCHER_C25_V1) += mach-archer-c25-v1.o obj-$(CONFIG_ATH79_MACH_ARCHER_C7) += mach-archer-c7.o +obj-$(CONFIG_ATH79_MACH_ARCHER_C7) += mach-archer-c7-v4.o obj-$(CONFIG_ATH79_MACH_ARDUINO_YUN) += mach-arduino-yun.o obj-$(CONFIG_ATH79_MACH_AW_NR580) += mach-aw-nr580.o obj-$(CONFIG_ATH79_MACH_BHR_4GRV2) += mach-bhr-4grv2.o diff --git a/target/linux/ar71xx/files/arch/mips/ath79/mach-archer-c7-v4.c b/target/linux/ar71xx/files/arch/mips/ath79/mach-archer-c7-v4.c new file mode 100644 index 0000000000000000000000000000000000000000..64955c79945c0b2c28d5a93be6e45662200e60ed --- /dev/null +++ b/target/linux/ar71xx/files/arch/mips/ath79/mach-archer-c7-v4.c @@ -0,0 +1,260 @@ + +/* + * Atheros ARCHER_C7 reference board support + * + * Copyright (c) 2017 Felix Fietkau + * Copyright (c) 2014 The Linux Foundation. All rights reserved. + * Copyright (c) 2012 Gabor Juhos + * + * Permission to use, copy, modify, and/or distribute this software for any + * purpose with or without fee is hereby granted, provided that the above + * copyright notice and this permission notice appear in all copies. + * + * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES + * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF + * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR + * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES + * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN + * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF + * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. + * + */ + +#include +#include +#include +#include +#include +#include +#include + +#include + +#include "common.h" +#include "dev-m25p80.h" +#include "machtypes.h" +#include "pci.h" +#include "dev-eth.h" +#include "dev-gpio-buttons.h" +#include "dev-leds-gpio.h" +#include "dev-spi.h" +#include "dev-usb.h" +#include "dev-wmac.h" + + +#define ARCHER_C7_GPIO_SHIFT_OE 1 +#define ARCHER_C7_GPIO_SHIFT_SER 14 +#define ARCHER_C7_GPIO_SHIFT_SRCLK 15 +#define ARCHER_C7_GPIO_SHIFT_RCLK 16 +#define ARCHER_C7_GPIO_SHIFT_SRCLR 21 + +#define ARCHER_C7_GPIO_BTN_RESET 5 +#define ARCHER_C7_GPIO_BTN_WPS_WIFI 2 + +#define ARCHER_C7_GPIO_LED_WLAN5 9 +#define ARCHER_C7_GPIO_LED_POWER 6 +#define ARCHER_C7_GPIO_LED_USB1 7 +#define ARCHER_C7_GPIO_LED_USB2 8 + +#define ARCHER_C7_74HC_GPIO_BASE QCA956X_GPIO_COUNT +#define ARCHER_C7_GPIO_LED_WPS (ARCHER_C7_74HC_GPIO_BASE + 0) +#define ARCHER_C7_GPIO_LED_LAN1 (ARCHER_C7_74HC_GPIO_BASE + 1) +#define ARCHER_C7_GPIO_LED_LAN2 (ARCHER_C7_74HC_GPIO_BASE + 2) +#define ARCHER_C7_GPIO_LED_LAN3 (ARCHER_C7_74HC_GPIO_BASE + 3) +#define ARCHER_C7_GPIO_LED_LAN4 (ARCHER_C7_74HC_GPIO_BASE + 4) +#define ARCHER_C7_GPIO_LED_WAN_GREEN (ARCHER_C7_74HC_GPIO_BASE + 5) +#define ARCHER_C7_GPIO_LED_WAN_AMBER (ARCHER_C7_74HC_GPIO_BASE + 6) +#define ARCHER_C7_GPIO_LED_WLAN2 (ARCHER_C7_74HC_GPIO_BASE + 7) + +#define ARCHER_C7_KEYS_POLL_INTERVAL 20 /* msecs */ +#define ARCHER_C7_KEYS_DEBOUNCE_INTERVAL (3 * ARCHER_C7_KEYS_POLL_INTERVAL) + +#define ARCHER_C7_MAC0_OFFSET 0 +#define ARCHER_C7_MAC1_OFFSET 6 +#define ARCHER_C7_WMAC_CALDATA_OFFSET 0x1000 + +#define ARCHER_C7_GPIO_MDC 3 +#define ARCHER_C7_GPIO_MDIO 4 + +static struct spi_gpio_platform_data archer_c7_v4_spi_data = { + .sck = ARCHER_C7_GPIO_SHIFT_SRCLK, + .miso = SPI_GPIO_NO_MISO, + .mosi = ARCHER_C7_GPIO_SHIFT_SER, + .num_chipselect = 1, +}; + +static u8 archer_c7_v4_ssr_initdata __initdata = 0xff; + +static struct gen_74x164_chip_platform_data archer_c7_v4_ssr_data = { + .base = ARCHER_C7_74HC_GPIO_BASE, + .num_registers = 1, + .init_data = &archer_c7_v4_ssr_initdata, +}; + +static struct platform_device archer_c7_v4_spi_device = { + .name = "spi_gpio", + .id = 1, + .dev = { + .platform_data = &archer_c7_v4_spi_data, + }, +}; + +static struct spi_board_info archer_c7_v4_spi_info[] = { + { + .bus_num = 1, + .chip_select = 0, + .max_speed_hz = 10000000, + .modalias = "74x164", + .platform_data = &archer_c7_v4_ssr_data, + .controller_data = (void *) ARCHER_C7_GPIO_SHIFT_RCLK, + }, +}; + +static struct gpio_led archer_c7_v4_leds_gpio[] __initdata = { + { + .name = "archer-c7-v4:green:power", + .gpio = ARCHER_C7_GPIO_LED_POWER, + .active_low = 1, + }, { + .name = "archer-c7-v4:green:wps", + .gpio = ARCHER_C7_GPIO_LED_WPS, + .active_low = 1, + }, { + .name = "archer-c7-v4:green:wlan2g", + .gpio = ARCHER_C7_GPIO_LED_WLAN2, + .active_low = 1, + }, { + .name = "archer-c7-v4:green:wlan5g", + .gpio = ARCHER_C7_GPIO_LED_WLAN5, + .active_low = 1, + }, { + .name = "archer-c7-v4:green:lan1", + .gpio = ARCHER_C7_GPIO_LED_LAN1, + .active_low = 1, + }, { + .name = "archer-c7-v4:green:lan2", + .gpio = ARCHER_C7_GPIO_LED_LAN2, + .active_low = 1, + }, { + .name = "archer-c7-v4:green:lan3", + .gpio = ARCHER_C7_GPIO_LED_LAN3, + .active_low = 1, + }, { + .name = "archer-c7-v4:green:lan4", + .gpio = ARCHER_C7_GPIO_LED_LAN4, + .active_low = 1, + }, { + .name = "archer-c7-v4:green:wan", + .gpio = ARCHER_C7_GPIO_LED_WAN_GREEN, + .active_low = 1, + }, { + .name = "archer-c7-v4:amber:wan", + .gpio = ARCHER_C7_GPIO_LED_WAN_AMBER, + .active_low = 1, + }, { + .name = "archer-c7-v4:green:usb1", + .gpio = ARCHER_C7_GPIO_LED_USB1, + .active_low = 1, + }, { + .name = "archer-c7-v4:green:usb2", + .gpio = ARCHER_C7_GPIO_LED_USB2, + .active_low = 1, + }, +}; + +static struct gpio_keys_button archer_c7_v4_gpio_keys[] __initdata = { + { + .desc = "WPS and WIFI button", + .type = EV_KEY, + .code = KEY_WPS_BUTTON, + .debounce_interval = ARCHER_C7_KEYS_DEBOUNCE_INTERVAL, + .gpio = ARCHER_C7_GPIO_BTN_WPS_WIFI, + .active_low = 1, + }, + { + .desc = "Reset button", + .type = EV_KEY, + .code = KEY_RESTART, + .debounce_interval = ARCHER_C7_KEYS_DEBOUNCE_INTERVAL, + .gpio = ARCHER_C7_GPIO_BTN_RESET, + .active_low = 1, + }, +}; + +static struct ar8327_pad_cfg archer_c7_v4_ar8337_pad0_cfg = { + .mode = AR8327_PAD_MAC_SGMII, + .sgmii_delay_en = true, +}; + +static struct ar8327_platform_data archer_c7_v4_ar8337_data = { + .pad0_cfg = &archer_c7_v4_ar8337_pad0_cfg, + .port0_cfg = { + .force_link = 1, + .speed = AR8327_PORT_SPEED_1000, + .duplex = 1, + .txpause = 1, + .rxpause = 1, + }, +}; + +static struct mdio_board_info archer_c7_v4_mdio0_info[] = { + { + .bus_id = "ag71xx-mdio.0", + .phy_addr = 0, + .platform_data = &archer_c7_v4_ar8337_data, + }, +}; + + +static void __init archer_c7_v4_setup(void) +{ + u8 *art = (u8 *) KSEG1ADDR(0x1fff0000); + u8 *mac = (u8 *) KSEG1ADDR(0x1ff00008); + + ath79_register_m25p80(NULL); + + spi_register_board_info(archer_c7_v4_spi_info, + ARRAY_SIZE(archer_c7_v4_spi_info)); + + platform_device_register(&archer_c7_v4_spi_device); + + gpio_request_one(ARCHER_C7_GPIO_SHIFT_OE, + GPIOF_OUT_INIT_LOW | GPIOF_EXPORT_DIR_FIXED, + "LED control"); + + gpio_request_one(ARCHER_C7_GPIO_SHIFT_SRCLR, + GPIOF_OUT_INIT_HIGH | GPIOF_EXPORT_DIR_FIXED, + "LED reset"); + + ath79_register_leds_gpio(-1, ARRAY_SIZE(archer_c7_v4_leds_gpio), + archer_c7_v4_leds_gpio); + + ath79_register_gpio_keys_polled(-1, ARCHER_C7_KEYS_POLL_INTERVAL, + ARRAY_SIZE(archer_c7_v4_gpio_keys), + archer_c7_v4_gpio_keys); + + ath79_register_usb(); + + ath79_gpio_output_select(ARCHER_C7_GPIO_MDC, QCA956X_GPIO_OUT_MUX_GE0_MDC); + ath79_gpio_output_select(ARCHER_C7_GPIO_MDIO, QCA956X_GPIO_OUT_MUX_GE0_MDO); + + ath79_register_mdio(0, 0x0); + + mdiobus_register_board_info(archer_c7_v4_mdio0_info, + ARRAY_SIZE(archer_c7_v4_mdio0_info)); + + ath79_register_wmac(art + ARCHER_C7_WMAC_CALDATA_OFFSET, mac); + ath79_register_pci(); + + /* GMAC0 is connected to an AR8337 switch */ + ath79_init_mac(ath79_eth0_data.mac_addr, mac, 0); + ath79_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_SGMII; + ath79_eth0_data.speed = SPEED_1000; + ath79_eth0_data.duplex = DUPLEX_FULL; + ath79_eth0_data.phy_mask = BIT(0); + ath79_eth0_data.mii_bus_dev = &ath79_mdio0_device.dev; + ath79_register_eth(0); +} + +MIPS_MACHINE(ATH79_MACH_ARCHER_C7_V4, "ARCHER-C7-V4", "TP-LINK Archer C7 v4", + archer_c7_v4_setup); diff --git a/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h b/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h index 9cb4a7f2e1df641232289721b676a9b0149c76e5..e4623fd08836d59ad4e79e96f02e75e502a55ca6 100644 --- a/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h +++ b/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h @@ -44,6 +44,7 @@ enum ath79_mach_type { ATH79_MACH_ARCHER_C5, /* TP-LINK Archer C5 board */ ATH79_MACH_ARCHER_C7, /* TP-LINK Archer C7 board */ ATH79_MACH_ARCHER_C7_V2, /* TP-LINK Archer C7 V2 board */ + ATH79_MACH_ARCHER_C7_V4, /* TP-LINK Archer C7 V4 board */ ATH79_MACH_ARDUINO_YUN, /* Yun */ ATH79_MACH_AW_NR580, /* AzureWave AW-NR580 */ ATH79_MACH_BHR_4GRV2, /* Buffalo BHR-4GRV2 */ diff --git a/target/linux/ar71xx/image/tp-link.mk b/target/linux/ar71xx/image/tp-link.mk index 5be7cbfbd4ab7d73d679d52d2581459250e04302..27d6c73454aef96e5da47033ec664d2caffca1d5 100644 --- a/target/linux/ar71xx/image/tp-link.mk +++ b/target/linux/ar71xx/image/tp-link.mk @@ -298,6 +298,22 @@ define Device/archer-c7-v2 IMAGE/factory-eu.bin := append-rootfs | mktplinkfw factory -C EU endef +define Device/archer-c7-v4 + DEVICE_TITLE := TP-LINK Archer C7 v4 + DEVICE_PACKAGES := kmod-ath10k ath10k-firmware-qca988x + BOARDNAME := ARCHER-C7-V4 + TPLINK_BOARD_NAME := ARCHER-C7-V4 + IMAGE_SIZE := 15104k + LOADER_TYPE := elf + KERNEL := kernel-bin | patch-cmdline | lzma | uImageArcher lzma + IMAGES := sysupgrade.bin factory.bin + IMAGE/sysupgrade.bin := append-rootfs | tplink-safeloader sysupgrade | \ + append-metadata | check-size $$$$(IMAGE_SIZE) + IMAGE/factory.bin := append-rootfs | tplink-safeloader factory + MTDPARTS := spi0.0:128k(factory-uboot)ro,128k(u-boot)ro,1536k(kernel),13568k(rootfs),960k(config)ro,64k(art)ro,15104k@0x40000(firmware) + SUPPORTED_DEVICES := archer-c7-v4 +endef + define Device/archer-c7-v2-il $(Device/tplink-16mlzma) DEVICE_TITLE := TP-LINK Archer C7 v2 IL @@ -316,7 +332,7 @@ define Device/tl-wdr7500-v3 DEVICE_PROFILE := ARCHERC7 TPLINK_HWID := 0x75000003 endef -TARGET_DEVICES += archer-c5-v1 archer-c7-v1 archer-c7-v2 archer-c7-v2-il tl-wdr7500-v3 +TARGET_DEVICES += archer-c5-v1 archer-c7-v1 archer-c7-v2 archer-c7-v2-il archer-c7-v4 tl-wdr7500-v3 define Device/tl-mr10u-v1 $(Device/tplink-4mlzma) diff --git a/tools/firmware-utils/src/tplink-safeloader.c b/tools/firmware-utils/src/tplink-safeloader.c index 478d5d8e9b43bbe37694732c138048c8fe8d807c..fec830c23ce6707755ddefc849f195872be1e877 100644 --- a/tools/firmware-utils/src/tplink-safeloader.c +++ b/tools/firmware-utils/src/tplink-safeloader.c @@ -376,6 +376,49 @@ static struct device_info boards[] = { .last_sysupgrade_partition = "file-system" }, + /** Firmware layout for the C7 */ + { + .id = "ARCHER-C7-V4", + .support_list = + "SupportList:\n" + "{product_name:Archer C7,product_ver:4.0.0,special_id:45550000}\n" + "{product_name:Archer C7,product_ver:4.0.0,special_id:55530000}\n" + "{product_name:Archer C7,product_ver:4.0.0,special_id:43410000}\n", + .support_trail = '\x00', + .soft_ver = "soft_ver:1.0.0\n", + + /** + We use a bigger os-image partition than the stock images (and thus + smaller file-system), as our kernel doesn't fit in the stock firmware's + 1MB os-image. + */ + .partitions = { + {"factory-boot", 0x00000, 0x20000}, + {"fs-uboot", 0x20000, 0x20000}, + {"os-image", 0x40000, 0x180000}, /* Stock: base 0x40000 size 0x120000 */ + {"file-system", 0x1c0000, 0xd40000}, /* Stock: base 0x160000 size 0xda0000 */ + {"default-mac", 0xf00000, 0x00200}, + {"pin", 0xf00200, 0x00200}, + {"device-id", 0xf00400, 0x00100}, + {"product-info", 0xf00500, 0x0fb00}, + {"soft-version", 0xf10000, 0x00100}, + {"extra-para", 0xf11000, 0x01000}, + {"support-list", 0xf12000, 0x0a000}, + {"profile", 0xf1c000, 0x04000}, + {"default-config", 0xf20000, 0x10000}, + {"user-config", 0xf30000, 0x40000}, + {"qos-db", 0xf70000, 0x40000}, + {"certificate", 0xfb0000, 0x10000}, + {"partition-table", 0xfc0000, 0x10000}, + {"log", 0xfd0000, 0x20000}, + {"radio", 0xff0000, 0x10000}, + {NULL, 0, 0} + }, + + .first_sysupgrade_partition = "os-image", + .last_sysupgrade_partition = "file-system", + }, + /** Firmware layout for the C9 */ { .id = "ARCHERC9", @@ -929,6 +972,9 @@ static void build_image(const char *output, strcasecmp(info->id, "TLWR1043NV5") == 0) { const char mdat[11] = {0x00, 0x00, 0x00, 0x02, 0x00, 0x00, 0x00, 0x00, 0x01, 0x00, 0x00}; parts[5] = put_data("extra-para", mdat, 11); + } else if (strcasecmp(info->id, "ARCHER-C7-V4") == 0) { + const char mdat[11] = {0x01, 0x00, 0x00, 0x02, 0x00, 0x00, 0xca, 0x00, 0x01, 0x00, 0x00}; + parts[5] = put_data("extra-para", mdat, 11); } size_t len;