From: Brian Norris Date: Mon, 25 May 2020 14:50:20 -0700 Subject: ipq40xx: Add subtarget for Google WiFi (Gale) Google WiFi (codename: Gale) is an IPQ4019-based AP, with 2 Ethernet ports, 2x2 2.4+5GHz WiFi, 512 MB RAM, 4 GB eMMC, and a USB type C port. In its stock configuration, it runs a Chromium OS-based system, but you wouldn't know it, since you can only manage it via a "cloud" + mobile-app system. The "v2" label is coded into the bootloader, which prefers the "google,gale-v2" compatible string. I believe "v1" must have been pre-release hardware. Note: this is *not* the Google Nest WiFi, released in 2019. I include "factory.bin" support, where we generate a GPT-based disk image with 2 partitions -- a kernel partition (using the custom "Chrome OS kernel" GUID type) and a root filesystem partition. See below for flashing instructions. Sysupgrade is supported via recent emmc_do_upgrade() helper. This is a subtarget because it enables different features (FEATURES=boot-part rootfs-part) whose configurations don't make sense in the "generic" target, and because it builds in a few USB drivers, which are necessary for installation (installation is performed by booting from USB storage, and so these drivers cannot be built as modules, since we need to load modules from USB storage). Flashing instructions ===================== Documented here: https://openwrt.org/inbox/toh/google/google_wifi Note this requires booting from USB storage. Features ======== I've tested: * Ethernet, both WAN and LAN ports * eMMC * USB-C (hub, power-delivery, peripherals) * LED0 (R/G/B) * WiFi (limited testing) * SPI flash * Serial console: once in developer mode, console can be accessed via the USB-C port with SuzyQable, or other similar "Closed Case Debugging" tools: https://chromium.googlesource.com/chromiumos/third_party/hdctools/+/master/docs/ccd.md#suzyq-suzyqable * Sysupgrade Not tested: * TPM Known not working: * Reboot: this requires some additional TrustZone / SCM configuration to disable Qualcomm's SDI. I have a proposal upstream, and based on IRC chats, this might be acceptable with additional DT logic: [RFC PATCH] firmware: qcom_scm: disable SDI at boot https://lore.kernel.org/linux-arm-msm/20200721080054.2803881-1-computersforpeace@gmail.com/ * SMP: enabling secondary CPUs doesn't currently work using the stock bootloader, as the qcom_scm driver assumes newer features than this TrustZone firmware has. I posted notes here: [RFC] qcom_scm: IPQ4019 firmware does not support atomic API? https://lore.kernel.org/linux-arm-msm/20200913201608.GA3162100@bDebian/ * There's a single external button, and a few useful internal GPIO switches. I haven't hooked them up. The first two are fixed with subsequent commits. Additional notes ================ Much of the DTS is pulled from the Chrome OS kernel 3.18 branch, which the manufacturer image uses. Note: the manufacturer bootloader knows how to patch in calibration data via the wifi{0,1} aliases in the DTB, so while these properties aren't present in the DTS, they are available at runtime: # ls -l /sys/firmware/devicetree/base/soc/wifi@a*/qcom,ath10k-pre-calibration-data -r--r--r-- 1 root root 12064 Jul 15 19:11 /sys/firmware/devicetree/base/soc/wifi@a000000/qcom,ath10k-pre-calibration-data -r--r--r-- 1 root root 12064 Jul 15 19:11 /sys/firmware/devicetree/base/soc/wifi@a800000/qcom,ath10k-pre-calibration-data Ethernet MAC addresses are similarly patched in via the ethernet{0,1} aliases. Signed-off-by: Brian Norris (updated 901 - x1pro moved in the process) Signed-off-by: Christian Lamparter (cherry picked from commit f1c041e34f9742fcdd0c8c65f69888d3ec580541) Signed-off-by: Jan-Niklas Burfeind (updated 901 - fixed offset, after missing drop commit) diff --git a/target/linux/ipq40xx/Makefile b/target/linux/ipq40xx/Makefile index b704e1b54efea35873661db9cb947412a54c41c7..6051c8294576a64d1ee80247addfedd4937758ff 100644 --- a/target/linux/ipq40xx/Makefile +++ b/target/linux/ipq40xx/Makefile @@ -6,7 +6,7 @@ BOARDNAME:=Qualcomm Atheros IPQ40XX FEATURES:=squashfs fpu ramdisk nand CPU_TYPE:=cortex-a7 CPU_SUBTYPE:=neon-vfpv4 -SUBTARGETS:=generic mikrotik +SUBTARGETS:=generic chromium mikrotik KERNEL_PATCHVER:=5.10 KERNEL_TESTING_PATCHVER:=5.10 diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network index a38d35a10dcf30e19e2e29a1a3ea1a6f4539afdb..5072e709421a403c4600cf35e81e8bea407149e8 100644 --- a/target/linux/ipq40xx/base-files/etc/board.d/02_network +++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network @@ -46,6 +46,7 @@ ipq40xx_setup_interfaces() cilab,meshpoint-one|\ edgecore,ecw5211|\ edgecore,oap100|\ + google,wifi|\ openmesh,a42|\ openmesh,a62) ucidef_set_interfaces_lan_wan "eth1" "eth0" diff --git a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh index e9c17e5b01e6fa86b1d8bd070d95c51d822a1997..f02500a86c41ad1df371a0fcbd4c7ab80f033c0e 100644 --- a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh +++ b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh @@ -153,6 +153,13 @@ platform_do_upgrade() { compex,wpj419) nand_do_upgrade "$1" ;; + google,wifi) + export_bootdevice + export_partdevice CI_ROOTDEV 0 + CI_KERNPART="kernel" + CI_ROOTPART="rootfs" + emmc_do_upgrade "$1" + ;; linksys,ea6350v3 |\ linksys,ea8300 |\ linksys,mr8300) @@ -202,7 +209,8 @@ platform_do_upgrade() { platform_copy_config() { case "$(board_name)" in - glinet,gl-b2200) + glinet,gl-b2200 |\ + google,wifi) emmc_copy_config ;; esac diff --git a/target/linux/ipq40xx/chromium/config-default b/target/linux/ipq40xx/chromium/config-default new file mode 100644 index 0000000000000000000000000000000000000000..83a42dfb663b045312eef331294a58d98ff3eb84 --- /dev/null +++ b/target/linux/ipq40xx/chromium/config-default @@ -0,0 +1,10 @@ +CONFIG_BLK_DEV_SD=y +CONFIG_BLK_SCSI_REQUEST=y +CONFIG_SCSI=y +CONFIG_SG_POOL=y +CONFIG_USB_DWC3=y +CONFIG_USB_DWC3_HOST=y +CONFIG_USB_DWC3_QCOM=y +CONFIG_USB_STORAGE=y +CONFIG_USB_XHCI_HCD=y +CONFIG_USB_XHCI_PLATFORM=y diff --git a/target/linux/ipq40xx/chromium/target.mk b/target/linux/ipq40xx/chromium/target.mk new file mode 100644 index 0000000000000000000000000000000000000000..3983a9281a5d20eccdba636c02c9622333d38699 --- /dev/null +++ b/target/linux/ipq40xx/chromium/target.mk @@ -0,0 +1,2 @@ +BOARDNAME:=Google Chromium +FEATURES += emmc boot-part rootfs-part diff --git a/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4019-wifi.dts b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4019-wifi.dts new file mode 100644 index 0000000000000000000000000000000000000000..9448e5145e29c39d4f7bfc2b94a745b2ccc1cf2d --- /dev/null +++ b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4019-wifi.dts @@ -0,0 +1,413 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (c) 2016, 2018 The Linux Foundation. All rights reserved. + * Copyright (c) 2016 Google, Inc + */ + +#include "qcom-ipq4019.dtsi" +#include +#include +#include + +/ { + model = "Google WiFi (Gale)"; + compatible = "google,wifi", "google,gale-v2", "qcom,ipq4019"; + + chosen { + /* + * rootwait: in case we're booting from slow/async USB storage. + */ + bootargs-append = " rootwait"; + stdout-path = &blsp1_uart1; + }; + + memory { + device_type = "memory"; + reg = <0x80000000 0x20000000>; /* 512MB */ + }; + + soc { + ess-switch@c000000 { + status = "okay"; + }; + + edma@c080000 { + status = "okay"; + }; + + ess-psgmii@98000 { + status = "okay"; + }; + }; +}; + +&tlmm { + fw_pinmux { + wp { + pins = "gpio53"; + output-low; + }; + recovery { + pins = "gpio57"; + bias-none; + }; + developer { + pins = "gpio41"; + bias-none; + }; + }; + + reset802_15_4 { + pins = "gpio60"; + }; + + led_reset { + pins = "gpio22"; + output-high; + }; + + sys_reset { + pins = "gpio19"; + output-high; + }; + + rx_active { + pins = "gpio43"; + bias-pull,down; + }; + + spi_0_pins: spi_0_pinmux { + pinmux { + function = "blsp_spi0"; + pins = "gpio13", "gpio14","gpio15"; + }; + pinmux_cs { + function = "gpio"; + pins = "gpio12"; + }; + pinconf { + pins = "gpio13", "gpio14","gpio15"; + drive-strength = <12>; + bias-disable; + }; + pinconf_cs { + pins = "gpio12"; + drive-strength = <2>; + bias-disable; + output-high; + }; + }; + + spi_1_pins: spi_1_pinmux { + pinmux { + function = "blsp_spi1"; + pins = "gpio44", "gpio46","gpio47"; + }; + pinmux_cs { + function = "gpio"; + pins = "gpio45"; + }; + pinconf { + pins = "gpio44", "gpio46","gpio47"; + drive-strength = <12>; + bias-disable; + }; + pinconf_cs { + pins = "gpio45"; + drive-strength = <2>; + bias-disable; + output-high; + }; + }; + + serial_0_pins: serial0_pinmux { + mux { + pins = "gpio16", "gpio17"; + function = "blsp_uart0"; + bias-disable; + }; + }; + + serial_1_pins: serial1_pinmux { + mux { + pins = "gpio8", "gpio9", "gpio10", "gpio11"; + function = "blsp_uart1"; + bias-disable; + }; + }; + + i2c_0_pins: i2c_0_pinmux { + mux { + pins = "gpio20", "gpio21"; + function = "blsp_i2c0"; + drive-open-drain; + }; + }; + + i2c_1_pins: i2c_1_pinmux { + mux { + pins = "gpio34", "gpio35"; + function = "blsp_i2c1"; + drive-open-drain; + }; + }; + + sd_0_pins: sd_0_pinmux { + sd0 { + pins = "gpio23", "gpio24", "gpio25", "gpio26", "gpio29", "gpio30", "gpio31", "gpio32"; + function = "sdio"; + drive-strength = <10>; + bias-pull-up; + pull-up-res = <0>; + }; + sdclk { + pins = "gpio27"; + function = "sdio"; + drive-strength = <2>; + bias-pull-up; + pull-up-res = <0>; + }; + sdcmd { + pins = "gpio28"; + function = "sdio"; + drive-strength = <10>; + bias-pull-up; + pull-up-res = <0>; + }; + }; + + mdio_pins: mdio_pinmux { + mux_1 { + pins = "gpio6"; + function = "mdio"; + bias-disable; + }; + mux_2 { + pins = "gpio7"; + function = "mdc"; + bias-disable; + }; + mux_3 { + pins = "gpio40"; + function = "gpio"; + bias-disable; + output-high; + }; + }; + + wifi1_1_pins: wifi2_pinmux { + mux { + pins = "gpio58"; + output-low; + }; + }; +}; + +&blsp_dma { + status = "okay"; +}; + +&blsp1_i2c3 { + pinctrl-0 = <&i2c_0_pins>; + pinctrl-names = "default"; + status = "okay"; + + tpm@20 { + compatible = "infineon,slb9645tt"; + reg = <0x20>; + powered-while-suspended; + }; +}; + +&blsp1_i2c4 { + pinctrl-0 = <&i2c_1_pins>; + pinctrl-names = "default"; + status = "okay"; + + led-controller@32 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "national,lp5523"; + reg = <0x32>; + clock-mode = /bits/ 8 <1>; + +#if 1 + led@0 { + reg = <0>; + chan-name = "LED0_Red"; + led-cur = /bits/ 8 <0x64>; + max-cur = /bits/ 8 <0x78>; + color = ; + }; + + led@1 { + reg = <1>; + chan-name = "LED0_Green"; + led-cur = /bits/ 8 <0x64>; + max-cur = /bits/ 8 <0x78>; + color = ; + }; + + led@2 { + reg = <2>; + chan-name = "LED0_Blue"; + led-cur = /bits/ 8 <0x64>; + max-cur = /bits/ 8 <0x78>; + color = ; + }; +#else + /* + * openwrt isn't ready to handle multi-intensity leds yet + * # echo 255 255 255 > /sys/class/leds/tricolor/multi_intensity + * # echo 255 > /sys/class/leds/tricolor/brightness + */ + multi-led@2 { + reg = <2>; + color = ; + #address-cells = <1>; + #size-cells = <0>; + + led@0 { + reg = <0>; + chan-name = "tricolor"; + led-cur = /bits/ 8 <0x64>; + max-cur = /bits/ 8 <0x78>; + color = ; + }; + + led@1 { + reg = <1>; + chan-name = "tricolor"; + led-cur = /bits/ 8 <0x64>; + max-cur = /bits/ 8 <0x78>; + color = ; + }; + + led@2 { + reg = <2>; + chan-name = "tricolor"; + led-cur = /bits/ 8 <0x64>; + max-cur = /bits/ 8 <0x78>; + color = ; + }; + }; +#endif + }; +}; + +&blsp1_spi1 { + pinctrl-0 = <&spi_0_pins>; + pinctrl-names = "default"; + status = "okay"; + cs-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <24000000>; + }; +}; + +&blsp1_spi2 { + pinctrl-0 = <&spi_1_pins>; + pinctrl-names = "default"; + status = "okay"; + cs-gpios = <&tlmm 45 GPIO_ACTIVE_HIGH>; + + /* + * This "spidev" was included in the manufacturer device tree. I + * suspect it's the (unused; and removed from later HW spins) Zigbee + * radio -- SiliconLabs EM3581 Zigbee? There's no driver or binding for + * this at the moment. + */ + spidev@0 { + compatible = "spidev"; + reg = <0>; + spi-max-frequency = <24000000>; + }; +}; + +&blsp1_uart1 { + pinctrl-0 = <&serial_0_pins>; + pinctrl-names = "default"; + status = "okay"; +}; + +&blsp1_uart2 { + pinctrl-0 = <&serial_1_pins>; + pinctrl-names = "default"; + status = "okay"; +}; + +&gmac0 { + qcom,phy_mdio_addr = <4>; + qcom,poll_required = <1>; + qcom,forced_speed = <1000>; + qcom,forced_duplex = <1>; + vlan_tag = <2 0x20>; +}; + +&gmac1 { + qcom,phy_mdio_addr = <3>; + qcom,forced_duplex = <1>; + vlan_tag = <1 0x10>; +}; + +&mdio { + status = "okay"; + pinctrl-0 = <&mdio_pins>; + pinctrl-names = "default"; +}; + +&prng { + status = "okay"; +}; + +&sdhci { + status = "okay"; + pinctrl-0 = <&sd_0_pins>; + pinctrl-names = "default"; + clock-frequency = <192000000>; + vqmmc-supply = <&vqmmc>; + non-removable; +}; + +&usb2 { + status = "okay"; +}; + +&usb2_hs_phy { + status = "okay"; +}; + +&usb3 { + status = "okay"; +}; + +&usb3_ss_phy { + status = "okay"; +}; + +&usb3_hs_phy { + status = "okay"; +}; + +&vqmmc { + status = "okay"; +}; + +&watchdog { + status = "okay"; +}; + +&wifi0 { + status = "okay"; + qcom,ath10k-calibration-variant = "GO_GALE"; +}; + +&wifi1 { + status = "okay"; + pinctrl-0 = <&wifi1_1_pins>; + pinctrl-names = "default"; + qcom,ath10k-calibration-variant = "GO_GALE"; +}; diff --git a/target/linux/ipq40xx/image/chromium.mk b/target/linux/ipq40xx/image/chromium.mk index 15d4c1a077e816056552261d09f64acf89530154..2c8457dcfbbb042e6bda08ae946e1219af4c4ffc 100644 --- a/target/linux/ipq40xx/image/chromium.mk +++ b/target/linux/ipq40xx/image/chromium.mk @@ -20,3 +20,17 @@ define Build/cros-vboot -k $@ -c "root=PARTUUID=%U/PARTNROFF=1" -o $@.new @mv $@.new $@ endef + +define Device/google_wifi + DEVICE_VENDOR := Google + DEVICE_MODEL := WiFi (Gale) + SOC := qcom-ipq4019 + KERNEL_SUFFIX := -fit-zImage.itb.vboot + KERNEL = kernel-bin | fit none $$(DTS_DIR)/$$(DEVICE_DTS).dtb | cros-vboot + KERNEL_NAME := zImage + IMAGES += factory.bin + IMAGE/factory.bin := cros-gpt | append-kernel-part | append-rootfs + DEVICE_PACKAGES := ipq-wifi-google_wifi partx-utils mkf2fs e2fsprogs \ + kmod-fs-ext4 kmod-fs-f2fs kmod-google-firmware +endef +TARGET_DEVICES += google_wifi diff --git a/target/linux/ipq40xx/patches-5.10/901-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-5.10/901-arm-boot-add-dts-files.patch index c51586a2329cd658321359cbc93817c5392fee7b..c30bc011d7deb1fd5af49cc89344d9ce10f75ffe 100644 --- a/target/linux/ipq40xx/patches-5.10/901-arm-boot-add-dts-files.patch +++ b/target/linux/ipq40xx/patches-5.10/901-arm-boot-add-dts-files.patch @@ -10,7 +10,7 @@ Signed-off-by: John Crispin --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile -@@ -904,11 +904,76 @@ dtb-$(CONFIG_ARCH_QCOM) += \ +@@ -904,11 +904,77 @@ dtb-$(CONFIG_ARCH_QCOM) += \ qcom-apq8074-dragonboard.dtb \ qcom-apq8084-ifc6540.dtb \ qcom-apq8084-mtp.dtb \ @@ -72,10 +72,11 @@ Signed-off-by: John Crispin + qcom-ipq4019-rtl30vw.dtb \ + qcom-ipq4019-srr60.dtb \ + qcom-ipq4019-srs60.dtb \ -+ qcom-ipq4019-x1pro.dtb \ + qcom-ipq4019-u4019-32m.dtb \ ++ qcom-ipq4019-wifi.dtb \ + qcom-ipq4019-wpj419.dtb \ + qcom-ipq4019-wtr-m2133hp.dtb \ ++ qcom-ipq4019-x1pro.dtb \ + qcom-ipq4028-wpj428.dtb \ + qcom-ipq4029-ap-303.dtb \ + qcom-ipq4029-ap-303h.dtb \