150 lines
4.6 KiB
Diff
150 lines
4.6 KiB
Diff
From: Paul Maruhn <paulmaruhn@posteo.de>
|
||
Date: Tue, 22 Mar 2022 21:06:42 +0100
|
||
Subject: ath79: support for TP-Link EAP225-Outdoor v3
|
||
|
||
This model is almost identical to the EAP225-Outdoor v1.
|
||
Major difference is the RTL8211FS PHY Chipset.
|
||
|
||
Device specifications:
|
||
* SoC: QCA9563 @ 775MHz
|
||
* Memory: 128MiB DDR2
|
||
* Flash: 16MiB SPI-NOR
|
||
* Wireless 2.4GHz (SoC): b/g/n 2x2
|
||
* Wireless 5GHz (QCA9886): a/n/ac 2x2 MU-MIMO
|
||
* Ethernet (RTL8211FS): 1× 1GbE, PoE
|
||
|
||
Flashing instructions:
|
||
* ssh into target device with recent (>= v1.6.0) firmware
|
||
* run `cliclientd stopcs` on target device
|
||
* upload factory image via web interface
|
||
|
||
Debricking:
|
||
To recover the device, you need access to the serial port. This requires
|
||
fine soldering to test points, or the use of probe pins.
|
||
* Open the case and solder wires to the test points: RXD, TXD and TPGND4
|
||
* Use a 3.3V UART, 115200 baud, 8n1
|
||
* Interrupt bootloader by holding ctrl+B during boot
|
||
* upload initramfs via built-in tftp client and perform sysupgrade
|
||
setenv ipaddr 192.168.1.1 # default, change as required
|
||
setenv serverip 192.168.1.10 # default, change as required
|
||
tftp 0x80800000 initramfs.bin
|
||
bootelf $fileaddr
|
||
|
||
MAC addresses:
|
||
MAC address (as on device label) is stored in device info partition at
|
||
an offset of 8 bytes. ath9k device has same address as ethernet, ath10k
|
||
uses address incremented by 1.
|
||
From stock ifconfig:
|
||
|
||
ath0 Link encap:Ethernet HWaddr D8:...:2E
|
||
ath10 Link encap:Ethernet HWaddr D8:...:2F
|
||
br0 Link encap:Ethernet HWaddr D8:...:2E
|
||
eth0 Link encap:Ethernet HWaddr D8:...:2E
|
||
|
||
Signed-off-by: Paul Maruhn <paulmaruhn@posteo.de>
|
||
Co-developed-by: Philipp Rothmann <philipprothmann@posteo.de>
|
||
Signed-off-by: Philipp Rothmann <philipprothmann@posteo.de>
|
||
[Add pre-calibraton nvme-cells]
|
||
Tested-by: Tido Klaassen <tido_ff@4gh.eu>
|
||
Signed-off-by: Nick Hainke <vincent@systemli.org>
|
||
|
||
diff --git a/target/linux/ath79/dts/qca9563_tplink_eap225-outdoor-v3.dts b/target/linux/ath79/dts/qca9563_tplink_eap225-outdoor-v3.dts
|
||
new file mode 100644
|
||
index 0000000000000000000000000000000000000000..e5914c9a55069e5baa5c7b989f3405c762e4d29d
|
||
--- /dev/null
|
||
+++ b/target/linux/ath79/dts/qca9563_tplink_eap225-outdoor-v3.dts
|
||
@@ -0,0 +1,59 @@
|
||
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||
+
|
||
+#include "qca9563_tplink_eap2x5-1port.dtsi"
|
||
+
|
||
+/ {
|
||
+ compatible = "tplink,eap225-outdoor-v3", "qca,qca9563";
|
||
+ model = "TP-Link EAP225-Outdoor v3";
|
||
+
|
||
+ aliases {
|
||
+ led-boot = &led_status_green;
|
||
+ led-failsafe = &led_status_amber;
|
||
+ led-running = &led_status_green;
|
||
+ led-upgrade = &led_status_amber;
|
||
+ };
|
||
+
|
||
+ leds {
|
||
+ compatible = "gpio-leds";
|
||
+
|
||
+ led_status_green: status_green {
|
||
+ label = "green:status";
|
||
+ gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
|
||
+ default-state = "on";
|
||
+ };
|
||
+
|
||
+ led_status_amber: status_amber {
|
||
+ label = "amber:status";
|
||
+ gpios = <&gpio 9 GPIO_ACTIVE_LOW>;
|
||
+ };
|
||
+ };
|
||
+};
|
||
+
|
||
+&art {
|
||
+ precalibration_ath10k: pre-calibration@5000 {
|
||
+ reg = <0x5000 0x2f20>;
|
||
+ };
|
||
+};
|
||
+
|
||
+ð0 {
|
||
+ phy-handle = <&phy6>;
|
||
+ phy-mode = "sgmii";
|
||
+};
|
||
+
|
||
+&mdio0 {
|
||
+ phy6: ethernet-phy@6 {
|
||
+ reg = <6>;
|
||
+ };
|
||
+};
|
||
+
|
||
+&pcie {
|
||
+ wifi@0,0 {
|
||
+ compatible = "qcom,ath10k";
|
||
+ reg = <0 0 0 0 0>;
|
||
+
|
||
+ mac-address-increment = <1>;
|
||
+
|
||
+ nvmem-cells = <&macaddr_info_8>, <&precalibration_ath10k>;
|
||
+ nvmem-cell-names = "mac-address", "pre-calibration";
|
||
+ };
|
||
+};
|
||
diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network b/target/linux/ath79/generic/base-files/etc/board.d/02_network
|
||
index 1ca89096bc73e4fe3d1e6a7628d7f35f27cc49a5..3a88b3cf677e0c59de191ebe9e7a82a50f7c6556 100644
|
||
--- a/target/linux/ath79/generic/base-files/etc/board.d/02_network
|
||
+++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network
|
||
@@ -77,6 +77,7 @@ ath79_setup_interfaces()
|
||
tplink,cpe610-v2|\
|
||
tplink,cpe710-v1|\
|
||
tplink,eap225-outdoor-v1|\
|
||
+ tplink,eap225-outdoor-v3|\
|
||
tplink,eap225-v1|\
|
||
tplink,eap225-v3|\
|
||
tplink,eap245-v1|\
|
||
diff --git a/target/linux/ath79/image/generic-tp-link.mk b/target/linux/ath79/image/generic-tp-link.mk
|
||
index fed572c884c75bd21081c7c22dd4652ecefdd993..3d3a45711302b7a73c914d80ec0d309878813149 100644
|
||
--- a/target/linux/ath79/image/generic-tp-link.mk
|
||
+++ b/target/linux/ath79/image/generic-tp-link.mk
|
||
@@ -401,6 +401,17 @@ define Device/tplink_eap225-outdoor-v1
|
||
endef
|
||
TARGET_DEVICES += tplink_eap225-outdoor-v1
|
||
|
||
+define Device/tplink_eap225-outdoor-v3
|
||
+ $(Device/tplink-eap2x5)
|
||
+ SOC := qca9563
|
||
+ IMAGE_SIZE := 13824k
|
||
+ DEVICE_MODEL := EAP225-Outdoor
|
||
+ DEVICE_VARIANT := v3
|
||
+ DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct
|
||
+ TPLINK_BOARD_ID := EAP225-V3
|
||
+endef
|
||
+TARGET_DEVICES += tplink_eap225-outdoor-v3
|
||
+
|
||
define Device/tplink_eap225-v1
|
||
$(Device/tplink-eap2x5)
|
||
SOC := qca9563
|