d427c94ee0
Device specifications:
======================
* Qualcomm/Atheros AR9330 rev 1
* 400/400/200 MHz (CPU/DDR/AHB)
* 64 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2x 10/100 Mbps Ethernet
* 1T1R 2.4 GHz Wi-Fi
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x fast ethernet
- eth0
+ builtin switch port 1
+ used as LAN interface
- eth1
+ 18-24V passive POE (mode B)
+ used as WAN interface
* 12-24V 1A DC
* internal antennas
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to
the device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
240 lines
5.4 KiB
Plaintext
240 lines
5.4 KiB
Plaintext
local ATH10K_PACKAGES_QCA9880 = {
|
|
'kmod-ath10k',
|
|
'-kmod-ath10k-ct',
|
|
'-kmod-ath10k-ct-smallbuffers',
|
|
'ath10k-firmware-qca988x',
|
|
'-ath10k-firmware-qca988x-ct',
|
|
}
|
|
|
|
local ATH10K_PACKAGES_QCA9887 = {
|
|
'kmod-ath10k',
|
|
'-kmod-ath10k-ct',
|
|
'-kmod-ath10k-ct-smallbuffers',
|
|
'ath10k-firmware-qca9887',
|
|
'-ath10k-firmware-qca9887-ct',
|
|
}
|
|
|
|
local ATH10K_PACKAGES_QCA9888 = {
|
|
'kmod-ath10k',
|
|
'-kmod-ath10k-ct',
|
|
'-kmod-ath10k-ct-smallbuffers',
|
|
'ath10k-firmware-qca9888',
|
|
'-ath10k-firmware-qca9888-ct',
|
|
}
|
|
|
|
-- devolo
|
|
|
|
device('devolo-wifi-pro-1200e', 'devolo_dvl1200e', {
|
|
packages = ATH10K_PACKAGES_QCA9880,
|
|
factory = false,
|
|
})
|
|
|
|
device('devolo-wifi-pro-1200i', 'devolo_dvl1200i', {
|
|
packages = ATH10K_PACKAGES_QCA9880,
|
|
factory = false,
|
|
})
|
|
|
|
device('devolo-wifi-pro-1750c', 'devolo_dvl1750c', {
|
|
packages = ATH10K_PACKAGES_QCA9880,
|
|
factory = false,
|
|
})
|
|
|
|
device('devolo-wifi-pro-1750e', 'devolo_dvl1750e', {
|
|
packages = ATH10K_PACKAGES_QCA9880,
|
|
factory = false,
|
|
})
|
|
|
|
device('devolo-wifi-pro-1750i', 'devolo_dvl1750i', {
|
|
packages = ATH10K_PACKAGES_QCA9880,
|
|
factory = false,
|
|
})
|
|
|
|
device('devolo-wifi-pro-1750x', 'devolo_dvl1750x', {
|
|
packages = ATH10K_PACKAGES_QCA9880,
|
|
factory = false,
|
|
})
|
|
|
|
|
|
-- Enterasys
|
|
|
|
device('enterasys-ws-ap3705', 'enterasys_ws-ap3705i', {
|
|
factory = false,
|
|
})
|
|
|
|
|
|
-- GL.iNet
|
|
|
|
device('gl.inet-gl-ar300m-lite', 'glinet_gl-ar300m-lite', {
|
|
factory = false,
|
|
})
|
|
|
|
-- JOY-IT
|
|
|
|
device('joy-it-jt-or750i', 'joyit_jt-or750i', {
|
|
packages = ATH10K_PACKAGES_QCA9887,
|
|
factory = false,
|
|
})
|
|
|
|
|
|
-- OCEDO
|
|
|
|
device('ocedo-raccoon', 'ocedo_raccoon', {
|
|
factory = false,
|
|
})
|
|
|
|
-- Onion
|
|
|
|
-- modular/optional "ethernet expansion board" recommended for config mode
|
|
-- setup via integrated (USB-)tty is possible as well
|
|
device('onion-omega', 'onion_omega')
|
|
|
|
|
|
-- OpenMesh
|
|
|
|
device('openmesh-a40', 'openmesh_a40', {
|
|
packages = ATH10K_PACKAGES_QCA9880,
|
|
factory = false,
|
|
})
|
|
|
|
device('openmesh-a60', 'openmesh_a60', {
|
|
packages = ATH10K_PACKAGES_QCA9880,
|
|
factory = false,
|
|
})
|
|
|
|
device('openmesh-mr600-v1', 'openmesh_mr600-v1', {
|
|
factory = false,
|
|
-- old name from OpenWrt 19.07.x
|
|
manifest_aliases = {'openmesh-mr600'},
|
|
})
|
|
|
|
device('openmesh-mr600-v2', 'openmesh_mr600-v2', {
|
|
factory = false,
|
|
-- old name from OpenWrt 19.07.x
|
|
manifest_aliases = {'openmesh-mr600v2'},
|
|
})
|
|
|
|
device('openmesh-mr900-v1', 'openmesh_mr900-v1', {
|
|
factory = false,
|
|
-- old name from OpenWrt 19.07.x
|
|
manifest_aliases = {'openmesh-mr900'},
|
|
})
|
|
|
|
device('openmesh-mr900-v2', 'openmesh_mr900-v2', {
|
|
factory = false,
|
|
-- old name from OpenWrt 19.07.x
|
|
manifest_aliases = {'openmesh-mr900v2'},
|
|
})
|
|
|
|
device('openmesh-mr1750-v1', 'openmesh_mr1750-v1', {
|
|
packages = ATH10K_PACKAGES_QCA9880,
|
|
factory = false,
|
|
-- old name from OpenWrt 19.07.x
|
|
manifest_aliases = {'openmesh-mr1750'},
|
|
})
|
|
|
|
device('openmesh-mr1750-v2', 'openmesh_mr1750-v2', {
|
|
packages = ATH10K_PACKAGES_QCA9880,
|
|
factory = false,
|
|
-- old name from OpenWrt 19.07.x
|
|
manifest_aliases = {'openmesh-mr1750v2'},
|
|
})
|
|
|
|
device('openmesh-om2p-v1', 'openmesh_om2p-v1', {
|
|
factory = false,
|
|
-- old name from OpenWrt 19.07.x
|
|
manifest_aliases = {'openmesh-om2p'},
|
|
})
|
|
|
|
device('openmesh-om2p-v2', 'openmesh_om2p-v2', {
|
|
factory = false,
|
|
-- old name from OpenWrt 19.07.x; deacticated at the moment because
|
|
-- the physical ethernet port for this device changed between 19.07
|
|
-- and 21.02. And automated update could therefore "break" the
|
|
-- device until someone physically changed the ethernet cable.
|
|
-- See https://github.com/freifunk-gluon/gluon/pull/2325#issuecomment-940749284
|
|
--manifest_aliases = {'openmesh-om2pv2'},
|
|
})
|
|
|
|
device('openmesh-om2p-v4', 'openmesh_om2p-v4', {
|
|
factory = false,
|
|
-- old name from OpenWrt 19.07.x
|
|
manifest_aliases = {'openmesh-om2pv4'},
|
|
})
|
|
|
|
device('openmesh-om2p-hs-v1', 'openmesh_om2p-hs-v1', {
|
|
factory = false,
|
|
-- old name from OpenWrt 19.07.x
|
|
manifest_aliases = {'openmesh-om2p-hs'},
|
|
})
|
|
|
|
device('openmesh-om2p-hs-v2', 'openmesh_om2p-hs-v2', {
|
|
factory = false,
|
|
-- old name from OpenWrt 19.07.x
|
|
manifest_aliases = {'openmesh-om2p-hsv2'},
|
|
})
|
|
|
|
device('openmesh-om2p-hs-v3', 'openmesh_om2p-hs-v3', {
|
|
factory = false,
|
|
-- old name from OpenWrt 19.07.x
|
|
manifest_aliases = {'openmesh-om2p-hsv3'},
|
|
})
|
|
|
|
device('openmesh-om2p-hs-v4', 'openmesh_om2p-hs-v4', {
|
|
factory = false,
|
|
-- old name from OpenWrt 19.07.x
|
|
manifest_aliases = {'openmesh-om2p-hsv4'},
|
|
})
|
|
|
|
device('openmesh-om2p-lc', 'openmesh_om2p-lc', {
|
|
factory = false,
|
|
})
|
|
|
|
|
|
-- Plasma Cloud
|
|
|
|
device('plasma-cloud-pa300', 'plasmacloud_pa300')
|
|
|
|
device('plasma-cloud-pa300e', 'plasmacloud_pa300e')
|
|
|
|
|
|
-- Siemens
|
|
|
|
device('siemens-ws-ap3610', 'siemens_ws-ap3610', {
|
|
factory = false,
|
|
})
|
|
|
|
-- TP-Link
|
|
|
|
device('tp-link-archer-a7-v5', 'tplink_archer-a7-v5', {
|
|
packages = ATH10K_PACKAGES_QCA9880,
|
|
})
|
|
|
|
device('tp-link-archer-c2-v3', 'tplink_archer-c2-v3', {
|
|
packages = ATH10K_PACKAGES_QCA9887,
|
|
class = 'tiny',
|
|
broken = true, -- 64M ath9k + ath10k
|
|
})
|
|
|
|
device('tp-link-archer-c6-v2', 'tplink_archer-c6-v2', {
|
|
packages = ATH10K_PACKAGES_QCA9888,
|
|
})
|
|
|
|
device('tp-link-archer-d50-v1', 'tplink_archer-d50-v1', {
|
|
packages = ATH10K_PACKAGES_QCA9880,
|
|
factory = false,
|
|
broken = true, -- 64M ath9k + ath10k & power LED not working
|
|
})
|
|
|
|
device('tp-link-cpe220-v3', 'tplink_cpe220-v3')
|
|
device('tp-link-cpe510-v2', 'tplink_cpe510-v2')
|
|
device('tp-link-cpe510-v3', 'tplink_cpe510-v3')
|
|
|
|
device('tp-link-eap225-outdoor-v1', 'tplink_eap225-outdoor-v1', {
|
|
packages = ATH10K_PACKAGES_QCA9888,
|
|
})
|
|
|
|
device('tp-link-tl-wdr3600-v1', 'tplink_tl-wdr3600-v1')
|
|
device('tp-link-tl-wdr4300-v1', 'tplink_tl-wdr4300-v1')
|
|
|
|
device('tp-link-wbs210-v2', 'tplink_wbs210-v2')
|