eed91a9be6
Device specifications:
======================
* Qualcomm/Atheros AR9341 rev 1
* 535/400/200 MHz (CPU/DDR/AHB)
* 64 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2x 10/100 Mbps Ethernet
* 2T2R 2.4 GHz Wi-Fi
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x fast ethernet
- eth0
+ 802.3af POE
+ builtin switch port 1
+ used as LAN interface
- eth1
+ 18-24V passive POE (mode B)
+ used as WAN interface
* 12-24V 1A DC
* internal antennas
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to
the device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Gluon image name change
=======================
The device had the image name "openmesh-om2phsv3" in older versions of Gluon.
This had to be changed with the new name in the device trees of the ath79
device tree.
|
||
|---|---|---|
| .github | ||
| contrib | ||
| docs | ||
| package | ||
| patches | ||
| scripts | ||
| targets | ||
| tests | ||
| .editorconfig | ||
| .gitignore | ||
| .luacheckrc | ||
| .readthedocs.yml | ||
| CONTRIBUTING.md | ||
| LICENSE | ||
| Makefile | ||
| modules | ||
| README.md | ||
Gluon
Gluon is a firmware framework to build preconfigured OpenWrt images for public mesh networks.
Getting started
We have a huge amount of documentation over at https://gluon.readthedocs.io/.
If you're new to Gluon and ready to get your feet wet, have a look at the Getting Started Guide.
Gluon's developers frequent an IRC chatroom at #gluon on hackint. There is also a webchat that allows for uncomplicated access from within your browser. This channel is also available as a bridged Matrix Room at #gluon:hackint.org.
Issues & Feature requests
Before opening an issue, make sure to check whether any existing issues (open or closed) match. If you're suggesting a new feature, drop by on IRC or our mailinglist to discuss it first.
We maintain a Roadmap for the future development of Gluon.
Use a release!
Please refrain from using the master branch for anything else but development purposes!
Use the most recent release instead. You can list all releases by running git tag
and switch to one by running git checkout v2021.1 && make update.
If you're using the autoupdater, do not autoupdate nodes with anything but releases. If you upgrade using random master commits the nodes might break eventually.
Mailinglist
To subscribe to the list, send a message to:
gluon+subscribe@luebeck.freifunk.net
To remove your address from the list, just send a message to
the address in the List-Unsubscribe header of any list
message. If you haven't changed addresses since subscribing,
you can also send a message to:
gluon+unsubscribe@luebeck.freifunk.net