nils/gluon
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
ff4050d873
gluon/patches/openwrt/0020-ipq40xx-add-support-for-Plasma-Cloud-PA1200.patch
Sven Eckelmann d4cb17777b
ipq40xx: Fix automatic ipq-wifi selection for Plasma Cloud devices (#2314) 
It was noticed that various devices had not the correct board-2.bin
installed. This was caused by a typo in the package name. The ath10k driver
(unfortunately) is then loading a completely unrelated BDF from the
ath10k-board-qca4019 board-2.bin. It is usually a rather bad idea to use
calibration data from a different board - but the effects depend on the
actual device.

For the PA1200, it was mostly noticed by the bad 2.4GHz performance.

Signed-off-by: Sven Eckelmann <sven@narfation.org>
2021-09-17 21:00:29 +02:00

478 lines
16 KiB
Diff
Raw Blame History

From: Marek Lindner <marek.lindner@kaiwoo.ai>
Date: Sun, 25 Nov 2018 21:46:54 +0800
Subject: ipq40xx: add support for Plasma Cloud PA1200
Device specifications:
* QCA IPQ4018
* 256 MB of RAM
* 32 MB of SPI NOR flash (w25q256)
- 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=PlasmaCloud-PA1200
* 2T2R 5 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=17,variant=PlasmaCloud-PA1200
* 3x GPIO-LEDs for status (cyan, purple, yellow)
* 1x GPIO-button (reset)
* 1x USB (xHCI)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
- phy@mdio4:
+ Label: Ethernet 1
+ gmac0 (ethaddr) in original firmware
+ used as LAN interface
- phy@mdio3:
+ Label: Ethernet 2
+ gmac1 (eth1addr) in original firmware
+ 802.3af/at POE(+)
+ used as WAN interface
* 12V/24V 1A DC
Flashing instructions:
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.
Signed-off-by: Marek Lindner <marek.lindner@kaiwoo.ai>
[sven@narfation.org: prepare commit message, rebase, use all LEDs, switch
to dualboot_datachk upgrade script, use eth1 as designated WAN interface]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Origin: backport, https://github.com/openwrt/openwrt/commit/ea5bb6bbfee06f44f714aff40c8929505face221
diff --git a/package/boot/uboot-envtools/files/ipq40xx b/package/boot/uboot-envtools/files/ipq40xx
index 7bcad00b010bfef49790c2699995c00573ed53ad..3d31de8083b63516322ca33e9de792a592cf4bf1 100644
--- a/package/boot/uboot-envtools/files/ipq40xx
+++ b/package/boot/uboot-envtools/files/ipq40xx
@@ -34,7 +34,8 @@ case "$board" in
alfa-network,ap120c-ac |\
glinet,gl-b1300 |\
openmesh,a42 |\
-openmesh,a62)
+openmesh,a62 |\
+plasmacloud,pa1200)
ubootenv_add_uci_config "/dev/mtd5" "0x0" "0x10000" "0x10000"
;;
linksys,ea6350v3)
diff --git a/package/firmware/ipq-wifi/Makefile b/package/firmware/ipq-wifi/Makefile
index cc0505b97c6a04bafd88972cf6ce7890a637c33b..5e181f67437ec644d07d8fc4882908549d3d60ef 100644
--- a/package/firmware/ipq-wifi/Makefile
+++ b/package/firmware/ipq-wifi/Makefile
@@ -34,6 +34,7 @@ ALLWIFIBOARDS:= \
engenius_ens620ext \
linksys_ea6350v3 \
linksys_ea8300 \
+ plasmacloud_pa1200 \
qxwlan_e2600ac
ALLWIFIPACKAGES:=$(foreach BOARD,$(ALLWIFIBOARDS),ipq-wifi-$(BOARD))
@@ -107,6 +108,7 @@ $(eval $(call generate-ipq-wifi-package,engenius_eap1300,EnGenius EAP1300))
$(eval $(call generate-ipq-wifi-package,engenius_ens620ext,EnGenius ENS620EXT))
$(eval $(call generate-ipq-wifi-package,linksys_ea6350v3,Linksys EA6350v3))
$(eval $(call generate-ipq-wifi-package,linksys_ea8300,Linksys EA8300))
+$(eval $(call generate-ipq-wifi-package,plasmacloud_pa1200,Plasma Cloud PA1200))
$(eval $(call generate-ipq-wifi-package,qxwlan_e2600ac,Qxwlan E2600AC))
$(foreach PACKAGE,$(ALLWIFIPACKAGES),$(eval $(call BuildPackage,$(PACKAGE))))
diff --git a/package/firmware/ipq-wifi/board-plasmacloud_pa1200.qca4019 b/package/firmware/ipq-wifi/board-plasmacloud_pa1200.qca4019
new file mode 100644
index 0000000000000000000000000000000000000000..99d6df8c8c2bd6ed8058b290e00aef09d74dbfb8
GIT binary patch
literal 24324
zcmeHPdsI_L8lQw9>e7`P0;1q0gzyMLfIu}!l&6$OiWC(Ix(L(<NsaO_Acn5k<AY*E
z1&d-5M5M?gO%XY+4+N{VwdW{j|JXnF>>q9S>~8;9_t>s_PJ7Po>dw94lAD(#np7V5
zgPHl}oB3wG`DI9M?)<p#rKLorY{-m_$%#r`my(|j<Z?NHQW1^i03^dyrl?+BT3!}e
zCYMINUoNePl5SfagV)OTlvZuSs<A5~Yf7u6rMvg8&f8U5EiX;mwMVfnDla8g5EDa#
zW3b_P>}d2ZjRxEfFyjlL2}E=P8Ylr^p@$b%1u*xD!!-t;n`b;82OA22xVX4yPoB_3
zta;#<znw@Tk{iq1!|wWR^PVRSGl3USjBOLfZllFiTLccWQ$R{O1FpsJL$qTt61uTW
zdi98ngFtN|Uc39i6R;<Kpn;7WCo&e3TuWkkczC$GyStGDfLo-Ml6zazeV~z?d|{oO
ztogjmwg}40+GkQ*MY9guHWOkR`KV5PtZsWzPL^==in_H<UbG=Ab+li7w5dw^Ue=1y
z0jO0=^RwRm1<Jjzd0}AmGj&s4Sy2{j98{mIlNRM=tr_jZx<Q)|Ivi`NEfQxX;tu!2
zBEaZn^>H}EyIBdNpF;;3?$84VDKE+qhQr}n>MDxzg)tKjVW#m-QLBS8MHka%%E1&5
z>$TZ{lJ%9%ENl0%(%OXWVFdv>cUr3sWXSnjeNu1rSGH#y4X^SmX&>0!o^X_1?Ooc_
zRH{fQ3thh~Yvkna`nA%?%|2_s>Z?1m?kK-{+50yJYTMsE7F8RtWB7RazBSu<1xUh8
z*e_ki-|W5SQjhd(X4CRo|MKgf)trw$5Ln?|GP6*kq9qV;_gL_ow-zDZK8u(5FC*UY
zNhS6k`!a#!zzZTQqtod$EO&E*AItM5#G|*NFvjoxhj{{&%MFIVA)KI~U``N+Q^1%H
zubn9Ql@TZ`%+KX;0^zJb|NP{~=g+Y#AR#X#*kJqbkAL}rY{NP(^YoxI82^L)7Qq+H
z=>PQTlYblfx_Su}I(R(-C#g8ltiuvEUu0xt#6*gW2oDYAa$(I0T0}TL7>C1gj%E!T
z1VxY(GzE!8W04BQ{sV_TZf-qmsQ?`&dOV*{L=!SHsi-Z4i8A@j2TWusx|F|E?1g$E
zerPJ1%1?ceie#hN{A_VDnv7(k0#v{kJP;tO&{h0Z;utgr5u%epXuGVdpo<7c*EOX|
z1St|t#%rn?N9ZQ0Q@XjTgT?`wG6w5ok=(pd@5kPVKkCo-7pI|VkJFGGG>4xfjzi-f
z$03PmB0o`VcoE2X$EQ#_$T>dbh@-hi3q?cDEl0riZpFu19XW-(rjR~btg6=jUS8EU
z8?H&IHQ4j&Qz%g=*+78W8a9A2G0#bqOc0<d6ao|i6ao|i6ao|ia~Ofeg2hN6^BuuE
z$U5dq!Ac~FIiC=aU)It!beEjt-<loHEazB2h|}hn!!IGVbO#Z5Y9S5|;HvKSo)FmE
z&sA}{Xk77@a@Fud0ARUK)j9moyyQpWH@&%Rbb4y=j(h~XI}hWVrWy=yBED&<xoBHC
zZP;Xh0Pi1o4FJS~P{;%dgoz7DP#l=B@+31Ba5w=0@HoXpPD8t;mBZQ6$^{}J4LsWe
zz-bSJmK+a2_<RJ2fQV5t4*_%^`ob-+^zy<F9i6rgYM|+dz>7go7M;Ego<P9UWjbU2
z87LQ^5RqPk@;WwgA$)V~9R9{u85SDCeUr&>a%VWJGn~$e^EMQ2DcM%8I(ho6rn9?O
zH#mIl)))7_dFXfpaQKpSra1uo98}C~Bu+x{Gf;7ABXJ6fpMQ!4jl>D4;~?7fnEmL^
zwB0aE;<e|@IJcm9M{`?8kN)b|*S7Ro0*A#iSkGBV02;s#5VJt~^K?Xviuq!3I*5NB
zkBCqaUnGuq+V^XV$?Y=u3VacinIXtPa+xaxE08tJqI1}fr8Dt4N0c+=D~_YQ`;~U_
z?*AG_qe0UBzLPi$+@}+`VZ3`Ej|Lnb1d@|*-aRCt5qObHp2TIm`zz#mF#V;xd-Kkd
zbpv%A<G<VD-J@`kMltZ;J?6Q&GbS1E01UsdkB&b)$&+6=$@eGm?v2wx&2&U3@cmgV
z7QhlAzP`QyON2OBe+vrX`l=-d%(LN|%<5$Qk#*aL?VIP@;5%rH(nf!C^S=!8rMca-
zuF;H-YdSqWO(`*^eH^LH$>UsV(e`YSX^4_NVLPV}(g?tM_y(=;qk~I-qT%TXERTFo
z1N*pi(66I|fuHE$;Wan#Si}H}ZZSa8YIlJ6xVd{cCj@E~3IPg%IfsCeH*bx1|DS*U
z{rm5}`!hskbz;Iwc&ilh?&r^A&>ube2eg^<?jJug@a_vX<mVZ9`_G>I^w{}ad~3Y>
z=x9D4OW1h>cITXfpFF(27P%b15zm1q1y0edZ7_Rz_r!Ox5r-7l^6rUHObPUq6-Qvi
z5ghEfheBrD8+6h<hS^-0V|$m(xySU^q}_*z3$dHsw;q~)!!XvY{k@QF-wutP*48Ks
zB+=hqA5&}VmBkX_*i~(tvQm;E3>h2JcdL{#i7){BU$K$fVc`Hev}zT~jS~L&p#GF<
zk1Ssz)DLSrWim;wFmmh<+7_i;k}70l4!7=vg#o;qOj)2T7{8&{s1&mGl9l=!sy10w
zX1Y)S9a@#U2#3)-VLUKCqVG`Ez;WLm8`NJ^)ypIjk$z02mhH`48}5hC@PTZzA*8W8
zFr@M8dbReTN-kSFc3I!0ZGz6Z`kShDSxshUxc}HS?I(Chfmlel?}qaLT<UrK39Uj^
z0z=Yj534Gb68&ZEd6_&jMHoGPQ{SbklWh_%H8}7>u{E@4_p5d&b75nLYM(4m5)A`s
zS1KeqLf-gQ{W(>YY+WW7bNJ#852AEstX*5JDpsbCUxSU+$}O^N80H0tWwH>3tr~5u
zEG=^h?r;yT!4a8;m-<vl_Pl@;N)$>q5SR^H!^YAm^PENC?9lE@NvES4{cA4hf2U4A
z5mvus_ujUQL%hnRWu6(gySE=-tqk6|SaM-#@1@k%=th6V(BKYj_NnE+_uq4(v!FS4
zKU=ma_p82LEy)cb@+HNp!HwsIrvmGlvc|q*jo=8XV3u9$t!zvFh*!njc(-5Ln$!@y
z%dfb8U}HyA<I<Ynmi7<UUQBKduU}lQQs*9y-RraIt+m(t%34+(V1MAV`OE9d{&niG
zgT8Y8WkpwF6Q_o`wW)pGk@y-viD%}OfvukiKMIul6!++*=hIKH6-Y_nK($tMm{aK`
z89ratoK_zx_szfmdG@i$x+OcjHuVke?96E4?q}^d+rPUbsVQ_HtMpR4v~i6hVyAab
zPw$>{iHCx#SjFf1O50P81ywVPPxnaAiH-zUdv7`3yy?Su8D}#yd8ofylY2b8)^Gcq
z-8j_3DFkK#0<ZfN4)`oAqgcUXu(3qwg+GNOB!mlp;S)I6!9hWspaL*$p2A_ti6?0H
z^PP5PZ#f4+yI<h6Ijq1>nJ5ITB49zge`?mvUebrN`<aC?*Q!(T?(t{M;KcFisfFUg
z<#IUFSL0&g;qgsBZTjzb$hU_~D2#L84XHz1PnaMJCK>YZ7k2X+u#|nrSmNAyI%9%6
z4`}I-w;z$ft(^Yrq#`s&0OQ3oATPe~Z0|i+@Z!zqb9UVp-=46)NzOesw`+O#y#oUS
z#?vZ;hCfovW`lWeSJbgbL0KKwW`ot<nDLGB?jeYM=8+NTy1d~+clSl}$$KzysKI=M
z8C~yyVs!z(Mnl_~Gi_EUcf7%#Gh<s^d$Qdaj!xIrOVmtt&EzJ!*kwy6JYTo$>N1XC
rOFySJ_OYeE8t)#TTxZBN*d$#RxehZ=C5A;9at+>@oEz-3n|J?zwKcxt
literal 0
HcmV?d00001
diff --git a/scripts/om-fwupgradecfg-gen.sh b/scripts/om-fwupgradecfg-gen.sh
index e271fa0dacad837191eaab7683ad8880d183a75e..552ed31f147df442926a39f7e2c8b3bd7b706571 100755
--- a/scripts/om-fwupgradecfg-gen.sh
+++ b/scripts/om-fwupgradecfg-gen.sh
@@ -7,7 +7,7 @@
#
usage() {
- echo "Usage: $0 <OM2P|OM5P|OM5PAC|MR600|MR900|MR1750|A60|A42|A62|PA300> <out file path> <kernel path> <rootfs path>"
+ echo "Usage: $0 <OM2P|OM5P|OM5PAC|MR600|MR900|MR1750|A60|A42|A62|PA300|PA1200> <out file path> <kernel path> <rootfs path>"
rm -f $CFG_OUT
exit 1
}
@@ -37,7 +37,7 @@ case $CE_TYPE in
SIZE_FACTOR=1
SIZE_FORMAT="%d"
;;
- A42)
+ A42|PA1200)
MAX_PART_SIZE=15616
KERNEL_FLASH_ADDR=0x180000
FLASH_BS=65536
diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network
index 49dd570242533068adf2c9df89e78560ba5f70eb..f446c04a00c863173c8fcb8242f7b2db1569acb3 100755
--- a/target/linux/ipq40xx/base-files/etc/board.d/02_network
+++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network
@@ -14,7 +14,8 @@ ipq40xx_setup_interfaces()
case "$board" in
8dev,jalapeno|\
alfa-network,ap120c-ac|\
- engenius,ens620ext)
+ engenius,ens620ext|\
+ plasmacloud,pa1200)
ucidef_set_interfaces_lan_wan "eth0" "eth1"
;;
asus,map-ac2200|\
diff --git a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index 15a2f2c09f8a92cc0accfbf9a977dbeb3355570d..28c34f6d0f9ebb47d0b2705e2edd5a55cc2e22eb 100644
--- a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -165,6 +165,7 @@ case "$FIRMWARE" in
engenius,eap1300 |\
openmesh,a42 |\
openmesh,a62 |\
+ plasmacloud,pa1200 |\
qxwlan,e2600ac-c1 |\
qxwlan,e2600ac-c2)
ath10kcal_extract "0:ART" 4096 12064
@@ -231,6 +232,7 @@ case "$FIRMWARE" in
engenius,eap1300 |\
openmesh,a42 |\
openmesh,a62 |\
+ plasmacloud,pa1200 |\
qxwlan,e2600ac-c1 |\
qxwlan,e2600ac-c2)
ath10kcal_extract "0:ART" 20480 12064
diff --git a/target/linux/ipq40xx/base-files/lib/upgrade/dualboot_datachk.sh b/target/linux/ipq40xx/base-files/lib/upgrade/dualboot_datachk.sh
index 807a85d43ccd57642b52e7c1a7f92295cb6cd036..60886071c9748407746ca9adfab52a1da9e524f2 100644
--- a/target/linux/ipq40xx/base-files/lib/upgrade/dualboot_datachk.sh
+++ b/target/linux/ipq40xx/base-files/lib/upgrade/dualboot_datachk.sh
@@ -44,6 +44,7 @@ platform_do_upgrade_dualboot_datachk() {
# boot anymore to Linux until it was reflashed with ap51-flash.
local next_boot_part="1"
case "$(board_name)" in
+ plasmacloud,pa1200|\
openmesh,a42)
primary_kernel_mtd=8
;;
diff --git a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
index 66e23b77a7bb0a484e88a11eed9d526e4fc04b50..6ec538cfd4cced656130169522cac1622a3b4ef2 100644
--- a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
@@ -73,7 +73,8 @@ platform_do_upgrade() {
nand_do_upgrade "$1"
;;
openmesh,a42 |\
- openmesh,a62)
+ openmesh,a62 |\
+ plasmacloud,pa1200)
PART_NAME="inactive"
platform_do_upgrade_dualboot_datachk "$1"
;;
diff --git a/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4018-pa1200.dts b/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4018-pa1200.dts
new file mode 100644
index 0000000000000000000000000000000000000000..bcb9552ce777d1d522c7642649e22ec26f04d7d2
--- /dev/null
+++ b/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4018-pa1200.dts
@@ -0,0 +1,197 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/* Copyright (c) 2017-2020, Sven Eckelmann <sven@narfation.org>
+ * Copyright (c) 2018, Marek Lindner <marek.lindner@kaiwoo.ai>
+ */
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/soc/qcom,tcsr.h>
+
+/ {
+ model = "Plasma Cloud PA1200";
+ compatible = "plasmacloud,pa1200";
+
+ soc {
+ rng@22000 {
+ status = "okay";
+ };
+
+ mdio@90000 {
+ status = "okay";
+ };
+
+ ess-psgmii@98000 {
+ status = "okay";
+ };
+
+ tcsr@194b000 {
+ /* select hostmode */
+ compatible = "qcom,tcsr";
+ reg = <0x194b000 0x100>;
+ qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
+ status = "okay";
+ };
+
+ tcsr@1949000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1949000 0x100>;
+ qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
+ };
+
+ ess_tcsr@1953000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1953000 0x1000>;
+ qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
+ };
+
+ tcsr@1957000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1957000 0x100>;
+ qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
+ };
+
+ usb2: usb2@60f8800 {
+ status = "okay";
+ };
+
+ crypto@8e3a000 {
+ status = "okay";
+ };
+
+ watchdog@b017000 {
+ status = "okay";
+ };
+
+ ess-switch@c000000 {
+ status = "okay";
+ };
+
+ edma@c080000 {
+ status = "okay";
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ gpios = <&tlmm 59 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+ };
+
+ aliases {
+ led-boot = &led_status_purple;
+ led-failsafe = &led_status_yellow;
+ led-running = &led_status_cyan;
+ led-upgrade = &led_status_yellow;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_status_cyan: status_cyan {
+ label = "cyan:status";
+ gpios = <&tlmm 0 GPIO_ACTIVE_HIGH>;
+ };
+
+ led_status_purple: status_purple {
+ label = "purple:status";
+ gpios = <&tlmm 1 GPIO_ACTIVE_HIGH>;
+ };
+
+ led_status_yellow: status_yellow {
+ label = "yellow:status";
+ gpios = <&tlmm 2 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+};
+
+&tlmm {
+ serial_pins: serial_pinmux {
+ mux {
+ pins = "gpio60", "gpio61";
+ function = "blsp_uart0";
+ bias-disable;
+ };
+ };
+
+ spi_0_pins: spi_0_pinmux {
+ pin {
+ function = "blsp_spi0";
+ pins = "gpio55", "gpio56", "gpio57";
+ drive-strength = <12>;
+ bias-disable;
+ };
+ pin_cs {
+ function = "gpio";
+ pins = "gpio54";
+ drive-strength = <2>;
+ bias-disable;
+ output-high;
+ };
+ };
+};
+
+&blsp_dma {
+ status = "okay";
+};
+
+&blsp1_spi1 {
+ pinctrl-0 = <&spi_0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>;
+
+ flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <24000000>;
+ /* partitions are passed via bootloader */
+ };
+};
+
+&blsp1_uart1 {
+ pinctrl-0 = <&serial_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&cryptobam {
+ status = "okay";
+};
+
+&gmac0 {
+ qcom,phy_mdio_addr = <4>;
+ qcom,poll_required = <1>;
+ qcom,forced_speed = <1000>;
+ qcom,forced_duplex = <1>;
+ vlan_tag = <2 0x20>;
+};
+
+&gmac1 {
+ qcom,phy_mdio_addr = <3>;
+ qcom,poll_required = <1>;
+ qcom,forced_speed = <1000>;
+ qcom,forced_duplex = <1>;
+ vlan_tag = <1 0x10>;
+};
+
+&usb2_hs_phy {
+ status = "okay";
+};
+
+&wifi0 {
+ status = "okay";
+ qcom,ath10k-calibration-variant = "PlasmaCloud-PA1200";
+};
+
+&wifi1 {
+ status = "okay";
+ qcom,ath10k-calibration-variant = "PlasmaCloud-PA1200";
+};
diff --git a/target/linux/ipq40xx/image/Makefile b/target/linux/ipq40xx/image/Makefile
index 68dcbc59a42f6d8360b87c7b4e74cd34f697b465..3a2e7a4410afcba1a1369cac328e237fc350668b 100644
--- a/target/linux/ipq40xx/image/Makefile
+++ b/target/linux/ipq40xx/image/Makefile
@@ -345,6 +345,21 @@ endef
TARGET_DEVICES += openmesh_a62
+define Device/plasmacloud_pa1200
+ $(call Device/FitImageLzma)
+ DEVICE_DTS := qcom-ipq4018-pa1200
+ DEVICE_DTS_CONFIG := config@pc.pa1200
+ BLOCKSIZE := 64k
+ DEVICE_TITLE := Plasma Cloud PA1200
+ KERNEL = kernel-bin | lzma | fit lzma $$(DTS_DIR)/$$(DEVICE_DTS).dtb | pad-to $$(BLOCKSIZE)
+ IMAGE_SIZE := 15616k
+ IMAGES = factory.bin sysupgrade.bin
+ IMAGE/factory.bin := append-rootfs | pad-rootfs | openmesh-image ce_type=PA1200
+ IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | sysupgrade-tar rootfs=$$$$@ | append-metadata
+ DEVICE_PACKAGES := uboot-envtools ipq-wifi-plasmacloud_pa1200
+endef
+TARGET_DEVICES += plasmacloud_pa1200
+
define Device/qcom_ap-dk01.1-c1
DEVICE_TITLE := QCA AP-DK01.1-C1
BOARD_NAME := ap-dk01.1-c1
diff --git a/target/linux/ipq40xx/patches-4.14/901-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-4.14/901-arm-boot-add-dts-files.patch
index fc8a88336491c2ac7c2a93fafb1f2b6fd38695be..cd0cd4164207f0a851d19a42fce07ad54fec8939 100644
--- a/target/linux/ipq40xx/patches-4.14/901-arm-boot-add-dts-files.patch
+++ b/target/linux/ipq40xx/patches-4.14/901-arm-boot-add-dts-files.patch
@@ -10,7 +10,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
-@@ -697,7 +697,32 @@ dtb-$(CONFIG_ARCH_QCOM) += \
+@@ -697,7 +697,33 @@ dtb-$(CONFIG_ARCH_QCOM) += \
qcom-apq8074-dragonboard.dtb \
qcom-apq8084-ifc6540.dtb \
qcom-apq8084-mtp.dtb \
@@ -24,6 +24,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
+ qcom-ipq4018-fritz4040.dtb \
+ qcom-ipq4018-jalapeno.dtb \
+ qcom-ipq4018-nbg6617.dtb \
++ qcom-ipq4018-pa1200.dtb \
+ qcom-ipq4018-rt-ac58u.dtb \
+ qcom-ipq4018-wre6606.dtb \
qcom-ipq4019-ap.dk01.1-c1.dtb \
Reference in New Issue View Git Blame Copy Permalink