ath79-generic: Add support for OpenMesh OM5P-AC v1
Device specifications:
======================
* Qualcomm/Atheros QCA9558 ver 1 rev 0
* 720/600/240 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2T2R 2.4 GHz Wi-Fi (11n)
* 2T2R 5 GHz Wi-Fi (11ac)
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* external h/w watchdog (enabled by default))
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* TI tmp423 (package kmod-hwmon-tmp421) for temperature monitoring
* 2x ethernet
- eth0
+ AR8035 ethernet PHY (RGMII)
+ 10/100/1000 Mbps Ethernet
+ 802.3af POE
+ used as LAN interface
- eth1
+ AR8035 ethernet PHY (SGMII)
+ 10/100/1000 Mbps Ethernet
+ 18-24V passive POE (mode B)
+ used as WAN interface
* 12-24V 1A DC
* internal antennas
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to the
device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Gluon image name change
=======================
The device had the image name "openmesh-om5p-ac" in older versions of Gluon.
This had to be changed with the new name in the device trees of the ath79
device tree.
This commit is contained in:
Sven Eckelmann
parent
e0abce03e6
commit
6e35f6b95a
@ -44,6 +44,7 @@ ath79-generic
|
|||||||
- OM2P-HS (v1, v2, v3, v4)
|
- OM2P-HS (v1, v2, v3, v4)
|
||||||
- OM2P-LC
|
- OM2P-LC
|
||||||
- OM5P
|
- OM5P
|
||||||
|
- OM5P-AC (v1)
|
||||||
|
|
||||||
* Plasma Cloud
|
* Plasma Cloud
|
||||||
|
|
||||||
|
|||||||
@ -0,0 +1,348 @@
|
|||||||
|
From: Sven Eckelmann <sven@narfation.org>
|
||||||
|
Date: Mon, 23 Nov 2020 13:41:34 +0100
|
||||||
|
Subject: ath79: Add support for OpenMesh OM5P-AC v1
|
||||||
|
|
||||||
|
Device specifications:
|
||||||
|
======================
|
||||||
|
|
||||||
|
* Qualcomm/Atheros QCA9558 ver 1 rev 0
|
||||||
|
* 720/600/240 MHz (CPU/DDR/AHB)
|
||||||
|
* 128 MB of RAM
|
||||||
|
* 16 MB of SPI NOR flash
|
||||||
|
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
|
||||||
|
* 2T2R 2.4 GHz Wi-Fi (11n)
|
||||||
|
* 2T2R 5 GHz Wi-Fi (11ac)
|
||||||
|
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
|
||||||
|
* external h/w watchdog (enabled by default))
|
||||||
|
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
|
||||||
|
* TI tmp423 (package kmod-hwmon-tmp421) for temperature monitoring
|
||||||
|
* 2x ethernet
|
||||||
|
- eth0
|
||||||
|
+ AR8035 ethernet PHY (RGMII)
|
||||||
|
+ 10/100/1000 Mbps Ethernet
|
||||||
|
+ 802.3af POE
|
||||||
|
+ used as LAN interface
|
||||||
|
- eth1
|
||||||
|
+ AR8035 ethernet PHY (SGMII)
|
||||||
|
+ 10/100/1000 Mbps Ethernet
|
||||||
|
+ 18-24V passive POE (mode B)
|
||||||
|
+ used as WAN interface
|
||||||
|
* 12-24V 1A DC
|
||||||
|
* internal antennas
|
||||||
|
|
||||||
|
Flashing instructions:
|
||||||
|
======================
|
||||||
|
|
||||||
|
Various methods can be used to install the actual image on the flash.
|
||||||
|
Two easy ones are:
|
||||||
|
|
||||||
|
ap51-flash
|
||||||
|
----------
|
||||||
|
|
||||||
|
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
|
||||||
|
used to transfer the image to the u-boot when the device boots up.
|
||||||
|
|
||||||
|
initramfs from TFTP
|
||||||
|
-------------------
|
||||||
|
|
||||||
|
The serial console must be used to access the u-boot shell during bootup.
|
||||||
|
It can then be used to first boot up the initramfs image from a TFTP server
|
||||||
|
(here with the IP 192.168.1.21):
|
||||||
|
|
||||||
|
setenv serverip 192.168.1.21
|
||||||
|
setenv ipaddr 192.168.1.1
|
||||||
|
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
|
||||||
|
|
||||||
|
The actual sysupgrade image can then be transferred (on the LAN port) to the
|
||||||
|
device via
|
||||||
|
|
||||||
|
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
|
||||||
|
|
||||||
|
On the device, the sysupgrade must then be started using
|
||||||
|
|
||||||
|
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
|
||||||
|
|
||||||
|
Signed-off-by: Sven Eckelmann <sven@narfation.org>
|
||||||
|
(cherry picked from commit 97f561725962ddb8823b2e01563a0f37f7930477)
|
||||||
|
|
||||||
|
diff --git a/package/boot/uboot-envtools/files/ath79 b/package/boot/uboot-envtools/files/ath79
|
||||||
|
index f4ccb2faea4e5e6202413a76cd137065dc535fe7..08c066c3494e8ea6fa5db639e11caa6406f3c6f9 100644
|
||||||
|
--- a/package/boot/uboot-envtools/files/ath79
|
||||||
|
+++ b/package/boot/uboot-envtools/files/ath79
|
||||||
|
@@ -58,6 +58,7 @@ openmesh,mr900-v2|\
|
||||||
|
openmesh,mr1750-v1|\
|
||||||
|
openmesh,mr1750-v2|\
|
||||||
|
openmesh,om5p|\
|
||||||
|
+openmesh,om5p-ac-v1|\
|
||||||
|
openmesh,om5p-ac-v2|\
|
||||||
|
samsung,wam250|\
|
||||||
|
ubnt,nanostation-m|\
|
||||||
|
diff --git a/target/linux/ath79/dts/qca9558_openmesh_om5p-ac-v1.dts b/target/linux/ath79/dts/qca9558_openmesh_om5p-ac-v1.dts
|
||||||
|
new file mode 100644
|
||||||
|
index 0000000000000000000000000000000000000000..ae69992abf583168a0ab9a017a9aee33758dd4d8
|
||||||
|
--- /dev/null
|
||||||
|
+++ b/target/linux/ath79/dts/qca9558_openmesh_om5p-ac-v1.dts
|
||||||
|
@@ -0,0 +1,199 @@
|
||||||
|
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||||
|
+
|
||||||
|
+#include "qca955x.dtsi"
|
||||||
|
+
|
||||||
|
+#include <dt-bindings/gpio/gpio.h>
|
||||||
|
+#include <dt-bindings/input/input.h>
|
||||||
|
+
|
||||||
|
+/ {
|
||||||
|
+ compatible = "openmesh,om5p-ac-v1", "qca,qca9558";
|
||||||
|
+ model = "OpenMesh OM5P-AC v1";
|
||||||
|
+
|
||||||
|
+ chosen {
|
||||||
|
+ /delete-property/ bootargs;
|
||||||
|
+ };
|
||||||
|
+
|
||||||
|
+ aliases {
|
||||||
|
+ serial0 = &uart;
|
||||||
|
+ led-boot = &led_power_blue;
|
||||||
|
+ led-failsafe = &led_power_blue;
|
||||||
|
+ led-running = &led_power_blue;
|
||||||
|
+ led-upgrade = &led_power_blue;
|
||||||
|
+ label-mac-device = ð0;
|
||||||
|
+ };
|
||||||
|
+
|
||||||
|
+ leds {
|
||||||
|
+ compatible = "gpio-leds";
|
||||||
|
+
|
||||||
|
+ led_power_blue: power_blue {
|
||||||
|
+ label = "blue:power";
|
||||||
|
+ gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
|
||||||
|
+ default-state = "on";
|
||||||
|
+ };
|
||||||
|
+
|
||||||
|
+ wan_blue {
|
||||||
|
+ label = "blue:wan";
|
||||||
|
+ gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
|
||||||
|
+ };
|
||||||
|
+
|
||||||
|
+ lan_blue {
|
||||||
|
+ label = "blue:lan";
|
||||||
|
+ gpios = <&gpio 20 GPIO_ACTIVE_LOW>;
|
||||||
|
+ };
|
||||||
|
+
|
||||||
|
+ wifi_green {
|
||||||
|
+ label = "green:wifi";
|
||||||
|
+ gpios = <&gpio 21 GPIO_ACTIVE_LOW>;
|
||||||
|
+ linux,default-trigger = "phy0tpt";
|
||||||
|
+ };
|
||||||
|
+
|
||||||
|
+ wifi_yellow {
|
||||||
|
+ label = "yellow:wifi";
|
||||||
|
+ gpios = <&gpio 22 GPIO_ACTIVE_LOW>;
|
||||||
|
+ };
|
||||||
|
+
|
||||||
|
+ wifi_red {
|
||||||
|
+ label = "red:wifi";
|
||||||
|
+ gpios = <&gpio 23 GPIO_ACTIVE_LOW>;
|
||||||
|
+ };
|
||||||
|
+ };
|
||||||
|
+
|
||||||
|
+ i2c {
|
||||||
|
+ compatible = "i2c-gpio";
|
||||||
|
+ gpios = <&gpio 11 GPIO_ACTIVE_HIGH /* sda */
|
||||||
|
+ &gpio 12 GPIO_ACTIVE_HIGH /* scl */
|
||||||
|
+ >;
|
||||||
|
+ #address-cells = <1>;
|
||||||
|
+ #size-cells = <0>;
|
||||||
|
+
|
||||||
|
+ i2c-gpio,scl-open-drain;
|
||||||
|
+ i2c-gpio,sda-open-drain;
|
||||||
|
+
|
||||||
|
+ tmp423a@4c {
|
||||||
|
+ compatible = "ti,tmp423";
|
||||||
|
+ reg = <0x4c>;
|
||||||
|
+ };
|
||||||
|
+ };
|
||||||
|
+
|
||||||
|
+ watchdog {
|
||||||
|
+ compatible = "linux,wdt-gpio";
|
||||||
|
+ gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
|
||||||
|
+ hw_algo = "toggle";
|
||||||
|
+ /* hw_margin_ms is actually 300s but driver limits it to 60s */
|
||||||
|
+ hw_margin_ms = <60000>;
|
||||||
|
+ always-running;
|
||||||
|
+ };
|
||||||
|
+};
|
||||||
|
+
|
||||||
|
+&spi {
|
||||||
|
+ status = "okay";
|
||||||
|
+
|
||||||
|
+ flash@0 {
|
||||||
|
+ compatible = "jedec,spi-nor";
|
||||||
|
+ reg = <0>;
|
||||||
|
+ spi-max-frequency = <40000000>;
|
||||||
|
+
|
||||||
|
+ /* partitions are passed via bootloader */
|
||||||
|
+ partitions {
|
||||||
|
+ compatible = "fixed-partitions";
|
||||||
|
+ #address-cells = <1>;
|
||||||
|
+ #size-cells = <1>;
|
||||||
|
+
|
||||||
|
+ partition@0 {
|
||||||
|
+ label = "u-boot";
|
||||||
|
+ reg = <0x000000 0x040000>;
|
||||||
|
+ read-only;
|
||||||
|
+ };
|
||||||
|
+
|
||||||
|
+ partition@40000 {
|
||||||
|
+ label = "u-boot-env";
|
||||||
|
+ reg = <0x040000 0x010000>;
|
||||||
|
+ };
|
||||||
|
+
|
||||||
|
+ partition@50000 {
|
||||||
|
+ label = "custom";
|
||||||
|
+ reg = <0x050000 0x060000>;
|
||||||
|
+ read-only;
|
||||||
|
+ };
|
||||||
|
+
|
||||||
|
+ partition@b0000 {
|
||||||
|
+ label = "inactive";
|
||||||
|
+ reg = <0x0b0000 0x7a0000>;
|
||||||
|
+ };
|
||||||
|
+
|
||||||
|
+ partition@850000 {
|
||||||
|
+ label = "inactive2";
|
||||||
|
+ reg = <0x850000 0x7a0000>;
|
||||||
|
+ };
|
||||||
|
+
|
||||||
|
+ art: partition@ff0000 {
|
||||||
|
+ label = "ART";
|
||||||
|
+ reg = <0xff0000 0x010000>;
|
||||||
|
+ read-only;
|
||||||
|
+ };
|
||||||
|
+ };
|
||||||
|
+ };
|
||||||
|
+};
|
||||||
|
+
|
||||||
|
+&mdio0 {
|
||||||
|
+ status = "okay";
|
||||||
|
+
|
||||||
|
+ phy-mask = <0x6>;
|
||||||
|
+
|
||||||
|
+ phy1: ethernet-phy@1 {
|
||||||
|
+ reg = <1>;
|
||||||
|
+ eee-broken-100tx;
|
||||||
|
+ eee-broken-1000t;
|
||||||
|
+ };
|
||||||
|
+
|
||||||
|
+ phy2: ethernet-phy@2 {
|
||||||
|
+ reg = <2>;
|
||||||
|
+ eee-broken-100tx;
|
||||||
|
+ eee-broken-1000t;
|
||||||
|
+ at803x-override-sgmii-link-check;
|
||||||
|
+ };
|
||||||
|
+};
|
||||||
|
+
|
||||||
|
+ð0 {
|
||||||
|
+ status = "okay";
|
||||||
|
+
|
||||||
|
+ pll-data = <0x82000101 0x80000101 0x80001313>;
|
||||||
|
+
|
||||||
|
+ mtd-mac-address = <&art 0x0>;
|
||||||
|
+
|
||||||
|
+ phy-mode = "rgmii-id";
|
||||||
|
+ phy-handle = <&phy1>;
|
||||||
|
+
|
||||||
|
+ gmac-config {
|
||||||
|
+ device = <&gmac>;
|
||||||
|
+ rgmii-enabled = <1>;
|
||||||
|
+ rxd-delay = <3>;
|
||||||
|
+ rxdv-delay = <3>;
|
||||||
|
+ txd-delay = <0>;
|
||||||
|
+ txen-delay = <0>;
|
||||||
|
+ };
|
||||||
|
+};
|
||||||
|
+
|
||||||
|
+ð1 {
|
||||||
|
+ status = "okay";
|
||||||
|
+
|
||||||
|
+ pll-data = <0x03000101 0x80000101 0x80001313>;
|
||||||
|
+
|
||||||
|
+ mtd-mac-address = <&art 0x6>;
|
||||||
|
+
|
||||||
|
+ qca955x-sgmii-fixup;
|
||||||
|
+
|
||||||
|
+ phy-handle = <&phy2>;
|
||||||
|
+};
|
||||||
|
+
|
||||||
|
+&wmac {
|
||||||
|
+ status = "okay";
|
||||||
|
+
|
||||||
|
+ mtd-cal-data = <&art 0x1000>;
|
||||||
|
+ mtd-mac-address = <&art 0x0>;
|
||||||
|
+ mac-address-increment = <2>;
|
||||||
|
+};
|
||||||
|
+
|
||||||
|
+&pcie1 {
|
||||||
|
+ status = "okay";
|
||||||
|
+};
|
||||||
|
diff --git a/target/linux/ath79/generic/base-files/etc/board.d/01_leds b/target/linux/ath79/generic/base-files/etc/board.d/01_leds
|
||||||
|
index f5384e7fc3859bab1d6c0422de7e173fad3abae2..68ea4281a56bff44147c7792990cc1e26bc10a7c 100755
|
||||||
|
--- a/target/linux/ath79/generic/base-files/etc/board.d/01_leds
|
||||||
|
+++ b/target/linux/ath79/generic/base-files/etc/board.d/01_leds
|
||||||
|
@@ -257,6 +257,10 @@ openmesh,om2p-v1)
|
||||||
|
ucidef_set_led_netdev "wan" "WAN" "blue:wan" "eth0"
|
||||||
|
ucidef_set_led_switch "lan" "LAN" "blue:lan" "switch0" "0x10"
|
||||||
|
;;
|
||||||
|
+openmesh,om5p-ac-v1)
|
||||||
|
+ ucidef_set_led_netdev "lan" "LAN" "blue:lan" "eth0"
|
||||||
|
+ ucidef_set_led_netdev "wan" "WAN" "blue:wan" "eth1"
|
||||||
|
+ ;;
|
||||||
|
pcs,cr3000)
|
||||||
|
ucidef_set_led_netdev "wan" "WAN" "blue:wan" "eth1"
|
||||||
|
ucidef_set_led_switch "lan1" "LAN1" "blue:lan1" "switch0" "0x04"
|
||||||
|
diff --git a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
|
||||||
|
index b70a87054b10fbe708d9aa8603ecdb591fc92591..00dbeec6a51457c23ba97aa627bf14acd8349f74 100644
|
||||||
|
--- a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
|
||||||
|
+++ b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
|
||||||
|
@@ -158,6 +158,10 @@ case "$FIRMWARE" in
|
||||||
|
;;
|
||||||
|
"ath10k/cal-pci-0000:01:00.0.bin")
|
||||||
|
case $board in
|
||||||
|
+ openmesh,om5p-ac-v1)
|
||||||
|
+ caldata_extract "ART" 0x5000 0x844
|
||||||
|
+ ath10k_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) +16)
|
||||||
|
+ ;;
|
||||||
|
sitecom,wlr-8100)
|
||||||
|
caldata_extract "art" 0x5000 0x844
|
||||||
|
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_ascii u-boot-env ethaddr) +1)
|
||||||
|
diff --git a/target/linux/ath79/generic/base-files/lib/upgrade/platform.sh b/target/linux/ath79/generic/base-files/lib/upgrade/platform.sh
|
||||||
|
index e9203f3a5b624e1e9b46c474e95e27583bcb6765..2cac42c9feaed3c0360091a5b7959e741d4a0473 100644
|
||||||
|
--- a/target/linux/ath79/generic/base-files/lib/upgrade/platform.sh
|
||||||
|
+++ b/target/linux/ath79/generic/base-files/lib/upgrade/platform.sh
|
||||||
|
@@ -82,6 +82,7 @@ platform_do_upgrade() {
|
||||||
|
openmesh,om2p-hs-v4|\
|
||||||
|
openmesh,om2p-lc|\
|
||||||
|
openmesh,om5p|\
|
||||||
|
+ openmesh,om5p-ac-v1|\
|
||||||
|
openmesh,om5p-ac-v2)
|
||||||
|
PART_NAME="inactive"
|
||||||
|
platform_do_upgrade_openmesh "$1"
|
||||||
|
diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk
|
||||||
|
index 8113b515368b253d0812fbbb86278e7fde63a038..75dbc1c03b5c42b81463bf7c4ddd4aa5803afd69 100644
|
||||||
|
--- a/target/linux/ath79/image/generic.mk
|
||||||
|
+++ b/target/linux/ath79/image/generic.mk
|
||||||
|
@@ -1810,6 +1810,17 @@ define Device/openmesh_om5p
|
||||||
|
endef
|
||||||
|
TARGET_DEVICES += openmesh_om5p
|
||||||
|
|
||||||
|
+define Device/openmesh_om5p-ac-v1
|
||||||
|
+ $(Device/openmesh_common_64k)
|
||||||
|
+ SOC := qca9558
|
||||||
|
+ DEVICE_MODEL := OM5P-AC
|
||||||
|
+ DEVICE_VARIANT := v1
|
||||||
|
+ DEVICE_PACKAGES += kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
||||||
|
+ OPENMESH_CE_TYPE := OM5PAC
|
||||||
|
+ SUPPORTED_DEVICES += om5p-ac
|
||||||
|
+endef
|
||||||
|
+TARGET_DEVICES += openmesh_om5p-ac-v1
|
||||||
|
+
|
||||||
|
define Device/openmesh_om5p-ac-v2
|
||||||
|
$(Device/openmesh_common_64k)
|
||||||
|
SOC := qca9558
|
||||||
@ -193,6 +193,13 @@ device('openmesh-om5p', 'openmesh_om5p', {
|
|||||||
factory = false,
|
factory = false,
|
||||||
})
|
})
|
||||||
|
|
||||||
|
device('openmesh-om5p-ac-v1', 'openmesh_om5p-ac-v1', {
|
||||||
|
packages = ATH10K_PACKAGES_QCA9880,
|
||||||
|
factory = false,
|
||||||
|
-- old name from OpenWrt 19.07.x
|
||||||
|
manifest_aliases = {'openmesh-om5p-ac'},
|
||||||
|
})
|
||||||
|
|
||||||
|
|
||||||
-- Plasma Cloud
|
-- Plasma Cloud
|
||||||
|
|
||||||
|
|||||||
Loading…
Reference in New Issue
Block a user