Set the compat-version of the sysupgrade image to 1.0 in order to allow
upgrades from Gluon-sources which are based on swconfig and do not
ignore mismatching minor compat-versions.
Signed-off-by: David Bauer <mail@david-bauer.net>
a4390ea283 apm821xx: WNDAP660: fix ethernet port ordering
7bc1d76419 ramips: mt7621-dts: fix claiming rgmii2 pin group for EdgeRouter X SFP
d01e374074 ramips: force ZyXEL NR7101 to boot from "Kernel" partition
b9d67e2608 ath79: fix rootfs padding for D-Link DAP-2xxx
4130e7ed54 mpc85xx: p2020: add RTC ds1307 to kernel
d929abbbde bcm53xx: remove 07_set_preinit_iface_bcm53xx
c1868ef656 tools/libressl: update to version 3.4.3
8a3fb45722 netfilter: kmod-nft-xfrm
43fd8f4aba libusb: fix missing link
f608779f92 mt76: update to the latest version
daa8d7e32d realtek: make "u-boot-env" partition writable for Netgear 3xx series
c32dfc7fe0 realtek: make Netgear GS1xx u-boot env partition writable
TP-Link TL-WR902AC v1 is a pocket-size, dual-band (AC750), successor of
TL-MR3020 (both devices use very similar enclosure, in same size). New
device is based on Qualcomm QCA9531 v2 + QCA9887. FCC ID: TE7WR902AC.
Specification:
- 650/391/216 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 1x USB 2.0 (GPIO-controlled power)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz (QCA9531)
- 1T1R 5 GHz (QCA9887)
- 5x LED (GPIO-controlled), 2x button, 1x 3-pos switch
- UART pads on PCB (TP1 -> TX, TP2 -> RX, TP3 -> GND, TP4 -> 3V3, jumper
resitors are missing on TX/RX lines)
- 1x micro USB (for power only)
Flash instructions:
Use "factory" image under vendor GUI.
Recovery instructions:
This device contains tftp recovery mode inside U-Boot. You can use it to
flash OpenWrt (use "factory" image) or vendor firmware.
1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "openwrt-ath79-generic-tplink_tl-wr902ac-v1-squashfs-factory.bin"
to "wr902acv1_un_tp_recovery.bin" and place it in tftp server dir.
3. Connect PC with LAN port, press the reset button, power up the router
and keep button pressed until WPS LED lights up.
4. Router will download file from server, write it to flash and reboot.
MAC Address summary:
- wlan1 (2.4GHz Wi-Fi): Label MAC
- wlan0 (5GHz Wi-Fi): Offset -1 from label
- eth0 (Wired): Offset +1 from label
Root access over serial line in vendor firmware: root/sohoadmin.
Based on support in ar71xx target by: Piotr Dymacz <pepe2k@gmail.com>
782f9a2b0 xray-core: Update to 1.5.8
976a19be5 cloudflared: Update to 2022.6.2
7fa87d732 v2raya: Update to 1.5.8.1
2869c80fc django: bump to version 4.0.5
d588074cc ddns-scripts: mydns.ip to mydns.jp
2d2f7a07f curl: bump to 7.83.1
618ab576be base-files: allow ignoring minor compat-version check
2726c8c315 ramips: fix booting on ZyXEL NBG-419N v2
515404a81b realtek: add support for power LED on Netgear GS108Tv3
bbf8651ba5 realtek: add support for power LED on Netgear GS308Tv1
OpenWrt now allows to specify the ifname of the transition interface
instead of SSID and BSSID, internally automatically detecting these from
interfaces on the same PHY. Thus, these cross-VAP dependant
configuration can be omitted from UCI.
Signed-off-by: David Bauer <mail@david-bauer.net>
Use the candelatech firmware for the QCA Wave-2 firmware.
The Qualcomm firmware used for the IPQ401x chip in OpenWrt in 22.03
is experiencing heavily degraded performance due to excessive
retransmits when using A-MSDU. Disabling VHT modes or switching to the
candelatech firmware circumvents this issue.
Apply the same to other Wave-2 platforms in order to keep consistency
with upstream.
Wave-1 chips do not support mesh modes with the -ct firmware, so keep
using the QCA firmware in their case.
Signed-off-by: David Bauer <mail@david-bauer.net>
656ed7aef openwisp-config: update to 1.0.0
29d26d1d0 xray-core: Update to 1.5.6
0647d444b cloudflared: Update to 2022.5.3
62514d596 yq: Update to 4.25.2
a9eed2e80 php8: update to 8.1.6
b42781523 php8: update to 8.1.5
a60cb1fbd libxml2: update to 2.9.14
dbe3820f3 pdns-recursor: update to 4.7.0
1646a22dd strongswan: support child rekey by bytes and packets
f765f2f114 ipq40xx: add Aruba AP-365 specific BDF
59e1b59bb3 malta: use default OpenWrt network configuration
dbd4c345fb firewall4: update to latest Git HEAD
dad1533030 ucode: update to latest Git HEAD
Gone due to
commit 071cf7b20f ("Switch to Lua for target definitions")
Has prior been introduced as untested -> broken in
commit d586720c5c ("ar71xx-generic: add support for Ubiquiti NanoBeam M5")
Was commented out in the former commit.
