We are mostly dealing with the 2.4GHz crap-band here, so increasing the
IGMP/MLD robustness parameter to three to be able to compensate for up
to two consecutive instead of just one lost packet.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
There are some devices not acting properly to roaming events, in that
they do not timely reissue IGMP/MLD reports after reconnecting.
To compensate for that this commit reduces the query interval from 125
seconds to 20 and the query response interval from 20 seconds to 5.
This reduces a timeout to 20+5 seconds in the worst-case (12.5s average)
after a roaming event for such broken devices. This should be below the
30s "impatient user threshold" and below any connection timeout.
Until the bridge multicast snooping + querier gets re-enabled this is a
no-op.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Adopt the according modifications to the default firewall settings of
the WAN interface from OpenWRT, revision 45613.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
An IGMP/MLD domain split will prevent us from being able to track
multicast listeners on other nodes.
Therefore we need to always hand any multicast packets we received from
local clients to batman-adv. With bridge multicast snooping disabled,
the current setting in Gluon, this is already the case.
However, in preparation to enabling multicast snooping, we need to
enforce forwarding towards batman-adv by setting the bridge port
option "multicast_router" to 2.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
It is not supported by all browsers yet.
Also change load display always to display 2 decimal digits (as it is read
from the kernel with 2 decimal digits).
Fixes#606
Mobile browsers will often show or hide the address bar while scrolling.
This causes resize events which would often reset the signal graphs.
Fixes#662
Ethernet links provide transitive connectivity in all but very unusual
setup, enable mesh_no_rebroadcast to reduce load for devices on links with
many nodes.
Fixes#652
This new feature introduces the new uci section 'gluon-core.wireless' with a preserve_channels option:
* preserve_channels (boolean)
By setting this option to 1 (true) wifi channels will be preserved during upgrades.
Instead of starting gluon-respondd from a hotplug handler, add a proper
init script. The new init script has a restart_if_running argument which
is now used by the hotplug handler.
introduce function to recurse down to the lowest layer-2 interface
corresponding to a given interface.
also re-introduce some of the previously removed input validation plus
some more to protect against glob and path based exploits.
The timeout was calculated incorrectly (in each iteration the span between
the start time and the current time was substracted from the timeout
again), and would often become negative, causing warnings in the kernel
log.
On the status page statistics section counters for transmitted and received traffic were mixed up. Transmitted traffic was shown as received while received traffic was shown as being transmitted.
Fixes#586
Is makes sense to always look for both ibss_radio* and mesh_radio* sections
to determine if the meshing should be enabled when regenerating these
sections. Doing this, the disabled state will survive updates changing the
section name (either updating from pre-2015.2 while keeping IBSS, or
changing from IBSS to 11s or vice-versa).
If both ibss_radio* and mesh_radio* sections exist, the disabled state will
be kept correctly for each section, the behaviour is changed only when
creating a section that didn't exist before.
Fixes#549
PKG_FILE_DEPENDS caused the whole site repo to be hashed to determine if
gluon-site needed rebuilding. While this is normally no problem,
alternative build setups sometimes put the Gluon repo inside the site repo,
causing long build times and parallel build failures.
in a layer 2 mesh network, multicast pings cause a lot of traffic in the
network, significantly increasing the 'backgroudn noise' (= Grundrauschen)
and stressing nodes in the network.
this commit blacklists all icmpv4 multicast traffic as well as multicast
icmpv6 echo-requests and node iformation queries. as no application
depending on these types of multicast traffic is known, blacklisting is safe.
gluon-radio-config contained only a single file. The code has been adjusted
to allow creating a Gluon configuration without WLAN support by removing
the wifi24 and wifi5 sections from site.conf.
The file promotes the probably unnecessary re-execution of the announce
scripts. Instead, gluon-announced should be queried using
gluon-neighbour-info -d ::1 -p 1001 -t0 -r nodeinfo
if both gluon-announced and gluon-neighbour-info are present. But to not
depend on any of those, no script for this one-liner is provided.
Now that the status page api has been rewritten in C CPU load and memory
usage is much lower. Also, nodes with both ibss and 11s mesh and dual
band wifi may require up to 9 connections for a single client, thus the
previous limit of 12 seemed a little low.
Convert option ifname in br-client to use a list instead. This
simplifies adding and remove interfaces:
uci:add_to_set("network", "client", "ifname", "eth0")
uci:remove_from_set("network", "client", "ifname", "eth0")
An option ifname will be automatically converted to a list when
performing an upgrade.
Packages affected: gluon-mesh-batman-adv-core, gluon-luci-portconfig
When rebooting the node in config mode, currently the fastd key is
forcefully displayed in a fixed format. This is confusing in communities
where fastd accepts all keys and no key submission is needed.
Furthermore, some communities might want to personalize the display of
the key (see #387).
This patch moves the displaying <div> from the package's lua file to the
translation files of the sample site configuration and mentiones the
change in the release notes.
Apart from replacing a patch for the former by two patches for latter,
this involved minimal adaptations of the lua scripts in the following
packages:
* gluon-announce
* gluon-announced
* gluon-mesh-batman-adv-core
* gluon-status-page
Split basic radio configuration from gluon-mesh-batman-adv as this will
be required for virtually any wireless mesh protocol.
This package takes care of setting:
- wireless channel,
- htmode and
- regulatory domain
gluon-mesh-batman-adv-core depends on this package.
