Specifications:
* SoC: AR7242 (Virian 400MHz)
* RAM: 64 MB DDR (W9751G6JB-25)
* Flash: 16MB SPI flash (S25FL129PIF)
* WiFi: AR9382 (2.4/5GHz) + 2x SE2595L
* LAN: 1x1000M (PEF7071V)
To install via EVA bootloader, a FTP connection need to be
established to 192.168.178.1 within the first seconds after power on:
ftp> quote USER adam2
ftp> quote PASS adam2
ftp> binary
ftp> debug
ftp> passive
ftp> quote MEDIA FLSH
ftp> put lede-ar71xx-generic-fritz300e-squashfs-sysupgrade.bin mtd1
Depending on the source of the primary MAC address, uppercase digits
would be used on some devices. Convert the address to lowercase for
consistency.
We only change the case for newly configured nodes to avoid changing the
node ID and derives MAC addresses for existing installations.
The Ubiquiti UniFi 6 LR now has a v2 with a different LED setup, thus
the previous model was added a v1 suffix.
Signed-off-by: David Bauer <mail@david-bauer.net>
Only restore the netifd proto for the WAN bridge in case the upgrade is
done from an older Gluon version.
For DSL targets, OpenWrt defaults the WAN proto to pppoe, while Gluon
uses the Ethernet ports for WAN. When unconditionally preserving the WAN
proto, pppoe is carried over to Gluon's network config.
Signed-off-by: David Bauer <mail@david-bauer.net>
Update the device-support version for image-metadata so that older Gluon
versions not implementing skipping minor compat-version checks are able
to update to newer Gluon versions.
Signed-off-by: David Bauer <mail@david-bauer.net>
There was never a device with a dedicated WAN port supported in Gluon
which could make use of such a workaround.
As the only relevant lantiq-xrx200 target now uses swconfig anyways,
we can remove this workaround.
Signed-off-by: David Bauer <mail@david-bauer.net>
Add a migration script to migrate the device path of PCIe WiFi hardware
from OpenWrt 19.07 to the one used with OpenWrt 21.02+.
Signed-off-by: David Bauer <mail@david-bauer.net>
Set the compat-version of the sysupgrade image to 1.0 in order to allow
upgrades from Gluon-sources which are based on swconfig and do not
ignore mismatching minor compat-versions.
Signed-off-by: David Bauer <mail@david-bauer.net>
a4390ea283 apm821xx: WNDAP660: fix ethernet port ordering
7bc1d76419 ramips: mt7621-dts: fix claiming rgmii2 pin group for EdgeRouter X SFP
d01e374074 ramips: force ZyXEL NR7101 to boot from "Kernel" partition
b9d67e2608 ath79: fix rootfs padding for D-Link DAP-2xxx
4130e7ed54 mpc85xx: p2020: add RTC ds1307 to kernel
d929abbbde bcm53xx: remove 07_set_preinit_iface_bcm53xx
c1868ef656 tools/libressl: update to version 3.4.3
8a3fb45722 netfilter: kmod-nft-xfrm
43fd8f4aba libusb: fix missing link
f608779f92 mt76: update to the latest version
daa8d7e32d realtek: make "u-boot-env" partition writable for Netgear 3xx series
c32dfc7fe0 realtek: make Netgear GS1xx u-boot env partition writable
TP-Link TL-WR902AC v1 is a pocket-size, dual-band (AC750), successor of
TL-MR3020 (both devices use very similar enclosure, in same size). New
device is based on Qualcomm QCA9531 v2 + QCA9887. FCC ID: TE7WR902AC.
Specification:
- 650/391/216 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 1x USB 2.0 (GPIO-controlled power)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz (QCA9531)
- 1T1R 5 GHz (QCA9887)
- 5x LED (GPIO-controlled), 2x button, 1x 3-pos switch
- UART pads on PCB (TP1 -> TX, TP2 -> RX, TP3 -> GND, TP4 -> 3V3, jumper
resitors are missing on TX/RX lines)
- 1x micro USB (for power only)
Flash instructions:
Use "factory" image under vendor GUI.
Recovery instructions:
This device contains tftp recovery mode inside U-Boot. You can use it to
flash OpenWrt (use "factory" image) or vendor firmware.
1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "openwrt-ath79-generic-tplink_tl-wr902ac-v1-squashfs-factory.bin"
to "wr902acv1_un_tp_recovery.bin" and place it in tftp server dir.
3. Connect PC with LAN port, press the reset button, power up the router
and keep button pressed until WPS LED lights up.
4. Router will download file from server, write it to flash and reboot.
MAC Address summary:
- wlan1 (2.4GHz Wi-Fi): Label MAC
- wlan0 (5GHz Wi-Fi): Offset -1 from label
- eth0 (Wired): Offset +1 from label
Root access over serial line in vendor firmware: root/sohoadmin.
Based on support in ar71xx target by: Piotr Dymacz <pepe2k@gmail.com>
782f9a2b0 xray-core: Update to 1.5.8
976a19be5 cloudflared: Update to 2022.6.2
7fa87d732 v2raya: Update to 1.5.8.1
2869c80fc django: bump to version 4.0.5
d588074cc ddns-scripts: mydns.ip to mydns.jp
2d2f7a07f curl: bump to 7.83.1
618ab576be base-files: allow ignoring minor compat-version check
2726c8c315 ramips: fix booting on ZyXEL NBG-419N v2
515404a81b realtek: add support for power LED on Netgear GS108Tv3
bbf8651ba5 realtek: add support for power LED on Netgear GS308Tv1
