Allow the transmission of IPv6 multicast packets as long as they are not
flooded through the whole mesh.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Set the ifname for the WAN radio (Private WLAN) to wanX, X being the
radio index.
All other radios created by Gluon already have their ifname defined
following this pattern.
Signed-off-by: David Bauer <mail@david-bauer.net>
The rudimentary flash size determination function expects the partition
for the devices firmware to be called "linux" while it is (since quite
some time) "firmware".
Fix this error to display available flash size as well as more useful
error message in case the uploaded firmware image exceeds the flash
space.
Signed-off-by: David Bauer <mail@david-bauer.net>
With batman-adv 2020.4 and the according backports to batman-adv v2019.2
several more bugs were found and fixed regarding the batman-adv
multicast optimizations feature.
Also a "wakeup-call" feature was added to the Linux bridge IGMP/MLD
snooping code in Gluon to work around issues with Android devices.
With batman-adv now at v2019.2, multicast-to-multi-unicasts conversion
is supported, too. Which means that even if there are a few outdated nodes
these and all other recipients will be served multicast packets via unicast,
too, as long as the sum of receiving nodes does not exceed the multicast
fanout setting (default: 16). If is exceeded, then batman-adv will revert
back to broadcast flooding automatically.
Long story short, with all these extra measures in place, let's reenable
the batman-adv multicast optimizations to reduce the layer 2 overhead
and in preparation for multicast applications in the future.
The default is enabled for this feature anyway, so removing the
"batctl multicast_mode 0" overwrite is sufficient.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
End the process after one result in case -l is not given
and destination address is unicast.
Reduces singleshot execution time from timeout seconds to around 150ms.
resolves#2184
This device is a dual 5GHz device. It is recommended to manually change the
radio of the first device to the lower 5GHz channels and the second radio
to the upper 5GHz channels
Fixes respondd on 64bit archs, as gluonutil_get_primary_domain() was
assumed to return int without the prototype.
Fixes: bcf57467dd ("libgluonutil: implement gluonutil_get_primary_domain()")
This adds the OpenWrt label-mac device selection as the most preferred
fallback.
While this is only used on OpenWrt 19.07 for backports, we can also use
the label-mac device when backporting device support. This way, we have
to deal with less device-sepcific code downstream.
Signed-off-by: David Bauer <mail@david-bauer.net>
This switches the used wireless daemons for OWE / SAE to the OpenSSL
flavors. The WolfSSL implementation currently seems to be broken.
THis switch may be reverted at a later point in time when hostapd /
wpa_supplicant implementations for WolfSSL have matured.
Specifications:
* SoC: MT7620A
* RAM: 64 MB DDR
* Flash: 8MB NOR SPI flash
* WiFi: MT7612E (5Ghz) and builtin MT7620A (2.4GHz)
* LAN: 1x100M
The -factory images can be flashed from the device's web
interface or via nmrpflash.
Both devices differ by a additional power outlet for the EX3800.
This patch has been tested on a EX3800 device.
This renames the local_client zone to loc_client, as local_clint exceeds
the maximum zone length allowed for firewall3, which is 11 bytes.
This worked previously due to firewall3 using unsafe string operations.
Now creation of the chain fails (latest OpenWrt master).
This allows running a respondd querier and map server behind a Gluon
node.
For instance at Freifunk Lübeck we now moved the map server
behind a Gluon VM and removed batman-adv and fastd from the
map server VM to reduce the maintenance work.
Increased multicast overhead should be minimal / non existent, as it is
unlikely to accidentally have respondd queriers running behind a Gluon
node.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
The rewrite of the feature handling introduced multiple major bugs. One
of them was caused by the way Lua's logical operators work:
An expression of the form
_'autoupdater' and _'web-advanced'
would return 'web-advanced' rather than the boolean true when _ returned
both strings unchanged (because the features are enabled).
As entries with more than a single feature name in their expressions did
not set no_default, Gluon would then attempt to add gluon-web-advanced to
the package selection, as web-advanced is a "pure" feature.
To fix this, and get rid of the annoying nodefault, separate handling of
"pure" feature and handling of logical expressions into two separate
functions, called feature() and when(). To simplify the feature
definitions, the package list is now passed directly to these functions
rather than in a table with a single field 'packages'.
Fixes: ee5ec5afe5 ("build: rewrite features.sh in Lua")
The new options are CONFIG_GLUON_AUTOUPDATER_BRANCH and
CONFIG_GLUON_AUTOUPDATER_ENABLED and allow to control the default branch
and default enable status separately.
The `or ''` fallback in targets/generic is removed, as GLUON_ENV will
set all variables in GLUON_VARS, making previously non-existing
variables exist with an empty value.
We already have a proper message when the creation of an alias fails
because of a name conflict. Also add a message when the primary filename
of a domain config is already occupied by another domain's alias.
Also add an 'Error:' prefix to the existing message to easier to see.
Reorder scripts so that the mesh_lan interface is accounted for.
Two other firewall upgrade scripts (mesh-babel and l3roamd) are
reordered as well. While there seems to be no hard dependency at the
moment, it makes sense to run the basic setup first, also to avoid
problems with future changes.
Closes: #2090
Fixes: ed094bc68c ("gluon-core: firewall: Allow custom gluon_wired interfaces (#2041)")
This adds the wireless client count for 2.4GHz and 5 GHz radios to the
status page. Previously, only the total client count advertised by
the mesh protocol was visible.
This will hide the outdoor mode setting on compatible devices in case
the defined channels should be preserved.
Otherwise a user might be under the impression their device is compliant
with outdoor operation when in reality it still uses prohibited
channels.
* build: target_config_lib: introduce concat_list helper
* build: rewrite features.sh in Lua
The `features` file is converted to a Lua-based DSL.
A helper function `_` is used in the DSL; this will return the original
string for enabled features, and nil for disabled features. This allows
to use boolean operations on features without making the code too
verbose.
Besides having more readable and robust code, this also fixes the bug
that all files `packages/*/features` were evaluated instead of only
using the feature definitions of currently active feeds.
* build: add luacheck support for package/features
Replace the ugly arrow shown in Firefox with a custom SVG arrow. Tested
and working in Firefox, Chrome and Edge. The arrow doesn't show in IE, but
the gluon-web-model JavaScript is already severely broken in IE, so we
don't care.
When the network connectivity is bad, routers may not appear in the
translation tables, or there may be no originator with TQ >0. Such
conditions to not warrant spamming the log with error messages.
The `features` file is converted to a Lua-based DSL.
A helper function `_` is used in the DSL; this will return the original
string for enabled features, and nil for disabled features. This allows
to use boolean operations on features without making the code too
verbose.
Besides having more readable and robust code, this also fixes the bug
that all files `packages/*/features` were evaluated instead of only
using the feature definitions of currently active feeds.
This commit changes the behavior for the wan-dnsmasq to read the
interfaces to update the DNS servers on from flag-files.
This way, external custom packages which add a custom VPN WAN interface
can update the DNS server gluon is using for WAN resolving.
On lantiq, the default WAN ifname is 'dsl0' even on devices that have a
separate WAN port. At least on devices using swconfig we can override
this with the switch port labelled as 'wan'.
With very bad timing, it is possible that the teardown script of a
gluon_mesh interface runs when bat0 was just created, but primary0 is not
yet added to it. Although there is no hardif to remove in this case,
bat0 will still be deleted, because there is no hardif in bat0.
Disable the interface removal logic by passing `-M` to `batctl interface`.
There is no setting to explicitly enable mesh interfaces in the config
wizard, so we need to enable mesh interfaces by default when the outdoor
mode is disabled (unless site.conf dictates otherwise).
The simplest way to achieve this is to delete the 5GHz mesh interface
sections when outdoor mode is disabled: 200-wireless would delete and
recreate them a moment later anyways, but by deleting them earlier we
ensure that the disabled status is initialized from site.conf again.
Because is_disabled() was always returning true or false, the
first_non_nil() would never actually check the default setting from
site.conf. This was broken since v2017.1.
Fixes: 6cf03bab37 ("treewide: replace normal uses of luci.model.uci with simple-uci to reduce LuCI dependencies")
With 11a3b56617 ("gluon-web-model: add dependency support for
sections"), a "reset" function was added to all model nodes. This
conflicts with the "reset" field of the Form object, making reset
buttons show labels like "function: 0xbb8d50" and possibly breaking form
processing when packages override the reset field.
The interfaces should always exist and just be disabled when outdoor
mode is enabled. Not creating them at all leads to an issue in the
advanced wifi settings where an additional reload of the page is
necessary after enabling or disabling the ourdoor mode to make the mesh
VIF options appear or disappear.
Instead of relying on the existence of interface sections only (which is
still used for the case of interface types that are not configured at
all in the site config), add a proper dependency.
This fixes section visiblity with enabled outdoor mode after the following
fix, and gives the user immediate feedback (allowing to disable outdoor
mode and enable meshing in a single step).
200-wireless will add or remove the mesh network sections of
/etc/config/network. Commit this file, so the modified setting doesn't
get lost on reboot.
Fixes: #2048
Validation errors are mostly handled in the frontend (by displaying
invalid fields with a red background). There was some code left in the
backend for handling different kinds of errors, and returning custom
error messages from validate(), but the resulting value was not used
anywhere.
- Add a dependency array to section template
- Lift dependency handling from AbstractValue to Node
- Split resolve_depends() into a function handling dependencies of a
node itself (resolve_node_depends()), which now is used for all nodes,
and the existing recursive descent through the node tree
- When any node's dependencies are not satisfied, all descendents are
reset recursively, meaning that an option in a section that is hidden
will always be ignored, as if the option's own dependencies were
unsatisfied
Fixes: #1349
- If luasrcdiet fails for a Lua script, this is a bug that should be
noticed rather than including the unminified script
- Use .tmp suffix for temporary file rather than .o
- Replace chmod + stat + mv with simpler cp + rm to overwrite file while
preserving file mode
gluonutil_get_interface_lower() recursively determines the lower of an
interface until the base interface is found.
gluonutil_get_interface_type() tries do distinguish wired, wireless and
tunnel interfaces. For tunnel interfaces, TUN/TAP, L2TPETH and Wireguard
are supported at the moment.
- Rename obtain_if_addr() to get_linklocal_address()
- Pass buffer of size INET6_ADDRSTRLEN instead of the oversized NI_MAXHOST
- Check if an address is link-local before converting to a string
- Replace an incorrect use of strncmp() with strcmp()
- Return status to caller
- Streamline control flow
While we're at it, the function handle_neighbour(), which is one of the
callers of get_linklocal_address() is slightly cleaned up as well.
This switches hostapd variant used for SAE and OWE from hostapd-openssl
to hostapd-wolfssl.
The bug shich one broke the wolfssl implementation was resolved upstream
with commit 631c437a91c2 ("hostapd: backport wolfssl bignum fixes").
This particular commit also got backported to OpenWrt 19.07.
This allows for multiple mesh legs out of one box. Useful for offloaders
and networks using vlan for separate mesh transport.
Custom mesh interfaces in a VXLAN domain are otherwise firewalled.
This fixes#1479
This adds support for the beacon interval to be set on a per-band base.
This has the potential to reduce the amount of airtime used up for
sending beacon frames.
Separate wireless-related helper methods from the util module to a
new wireless module. This keeps them separated, as the amount of
wireless helpers increased in the past, justifying a separate module.
xt_CT was added to kmod-ipt-conntrack a while back. Update our
GLUON_SPECIALIZE_KERNEL rules accordingly.
When building xt_CT into the kernel, one of the symbols IP_NF_RAW and
IP6_NF_RAW must be enabled as well, even though there is no runtime
dependency when building as modules. The kernel grows by less than 1KB
even when both IP_NF_RAW and NETFILTER_XT_TARGET_CT are enabled, making
this change a (very slight) net win in both flash and RAM usage.
As a partial fix to #496, do not touch the MAC address of the WAN
interface when using VXLANs (as only the MAC address of the VXLAN
interface matters to batman-adv).
On PoE-powered devices, we usually want to use WAN for the setup mode.
As all outdoor devices are PoE-powered, we can reuse this function. This
switches the setup mode interface for new installations / after config
reset on a few devices that were missing in this list before.
The 'preserve' flag can be used to mark a peer so it is not removed or
modified on upgrades. In addition, groups containing preserved peers are
not removed.
Fixes: #557
The netdev() lookup is confusing to use: whenever a interface does not
exist during boot (for example VLAN) or when the address is overridden
from board.json (which is not obvious at all), it will yield either no
address, or a different address than expected.
To avoid this confusion, using board.json-based interface() is
preferable. This converts all uses of netdev() to the corresponding
lan/wan lookups, except for the final fallback for eth0.
- Replace misnamed, closure-returning sysfs() to a reusable read() function
- Rename eth() to netdev(), pass full interface name
- Rename board() to interface()
- Split reuable get_netdev_addr() out of netdev()
gsub() returns the number of matches as its second return value. This
was unintendedly passed through by the util functions trim() and
node_id(). It can be presumed that this had no effect in practice, but
it can lead to surprising output when passing values to print() for
debugging.
Allows reconfigurtion of remote syslog from within site.conf.
Conflicts with the gluon-web-logging package as user made changes
will be overwritten, because this package will reconfigure the syslog
destination on every upgrade.
Resolves#1845
Use the value of the `name` site.conf field as label (it was
accidentally unused before).
Our site.conf currently doesn't define a specific order for the branch
entries. To avoid changing branch orders, sort entries by this label.
Fixes: #1961
Register to 'reset' event on form element and make call to 'update' function
delayed in 'data-update' handler to allow the form values to update beforehand.
When using a form's 'reset' button, form field visibility was not updated.
This could lead to situations where a checkbox had to be toggled again
twice to display the detail text inputs. (Example taken from private
wifi package)
This adds a helper method, which determines if the current platform
supports WPA3 or not.
WPA3 is supported if
- the device is not in the featureset category "tiny"
- the WiFi driver supports 802.11w management frame protection
The gluon-wireless-encryption package selects a WPA3 supporting
hostapd package as a dependency and stores the information, which
encryption method is supported to the device.
This package adds support for SAE on 802.11s mesh connections.
Enabling this package will require all 802.11s mesh connections
to be encrypted using the SAE key agreement scheme. The security
of SAE relies upon the authentication through a shared secret.
In the context of public mesh networks a shared secret is an
obvious oxymoron. Still this functionality provides an improvement
over unencrypted mesh connections in that it protects against a
passive attacker who did not observe the key agreement. In addition
Management Frame Protection (802.11w) gets automatically enabled on
mesh interfaces to prevent protocol-level deauthentication attacks.
If `wifi.mesh.sae` is enabled a shared secret will automatically be
derived from the `prefix6` variable. This is as secure as it gets
for a public mesh network.
For *private* mesh networks `wifi.mesh.sae_passphrase` should be
set to your shared secret.
Fixes#1636
Remove a lot of redundant code by switching to a match table listing
the targets and boards for each candidate for the primary MAC interface.
In addition, we add some flexiblity by allow to switch out the sysfs file
data source for the MAC address.
This reverts commits
- caf2dd037b.
- 07ebac6a49
- 55eff45f96
I accidentally pushed these commits as I had them lying around on a
dirty checkout I did testing on.
In addition this PR contains:
- split of gluon-respondd provider into multiple source files
- minor additional cleanups in gluon-mesh-babel respondd provider
(untested, as the babel respondd provider already doesn't compile prior
to these changes...)
many AVM devices do not have RESET/WPS buttons. So use the otherwise unused DECT/PHONE button to boot the device into setup mode.
This patch allows to enter the setup-mode by pressing the phone button
(often labeled as DECT) in addition to WPS and reset button.
This patch is necessary to allow supporting boards without a WPS and reset
button (e.g. AVM FRITZ!Box 7312).
With this commit, the status-led is set to be the "led-running"
device-tree alias for targets which do not implement the get_status_led
method in /etc/diag.sh.
This reverts commit 9b1eb40fe7.
With the batman-adv v2019.2 upgrade reverted (c1a7733956), the batman-adv
multicast-to-multi-unicast feature is not available yet. Without that it is
going to be very unlikely of the batman-adv multicast optimizations to
take effect. E.g. some outdated nodes would disable it.
To avoid confusion and diversion with a few communities having it enabled
and most implicitly deactivated, just deactivate it for all for now
until batman-adv is updated to v2019.2 or greater again.
mac_to_ip() calculates an ipv6 address from a mac address according to
RFC 4291. For wireguard we have to use specially crafted addresses that
must be unique. This allows calculating such unique mac-based addresses
by allowing to optionally specifying the bytes to be inserted into the
address.
The new routing_algo site.conf value BATMAN_IV_LEGACY is introduced. With
these changes, the routing_algo setting becomes mandatory.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
We cannot add the same file (here: /lib/gluon/mesh-batman-adv/compat) to
two, installed packages. Therefore, instead of determining the compat
version number from this file, infer it from the batman-adv release
version number instead.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
This is a fix for the broken ingress traffic-shaping in gluon v2018.2.2
and possibly earlier.
For ingress traffic shaping the kernel option NET_ACT_POLICE is needed.
Before this patch there was no dependency to this. Neither in
gluon_core, gluon-mesh-vpn-core nor in the package.
This patch adds this dependency.
[Matthias Schiffer: move dependency from GLUON_CORE to gluon-mesh-vpn-core]
Fixes#1790
package/gluon-web-network/luasrc/lib/gluon/config-mode/model/admin/network.lua:122:16: (W431) shadowing upvalue f on line 19
Fixes: bab4af01e ("gluon-web-network: improve PoE GPIO name translation
handling")
The gluon-authorized-keys is usually installed to use SSH keys to
authenticate a user against the device. To make this useful, it is also
required to disable passwordless SSH access to the device.
This new dependency is only required when the user doesn't have
gluon-setup-mode enabled already.
Fixes: #1777
Reported-by: yanosz <github@yanosz.net>
Fixes: a753fa79e3 ("gluon-authorized-keys: add keys from site.conf")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
This MR includs only the VPN MODE of the hoodselector whitch simply set
hoods base on their geopositions.
Signed-off-by: Jan-Tarek Butt <tarek@ring0.de>
check_site.lua: fix language syntax
muss -> must
rage -> range
at lease -> at least
coordiantes -> coordinates
realaise -> realised
gluon-hoodselector: fix language syntax in hoodselector
can not -> can't
routers -> router's
continure -> continue
to next -> to the next
TMP -> temporary
for current -> for the current
continure -> continue
with next -> with the next
thier -> there
provides -> provide
possition -> position
therfore -> therefore
gluon-hoodselector: fix language syntax in util.lua
realaise -> realised
gluon-hoodselector: fix language syntax and use autoupdate lock mechanism.
gluon-hoodselector: fix spelling/grammar
gluon-hoodselector: automatically set SECTION and CATEGORY for Gluon packages
gluon-hoodselector-add-VPN-MODE: add micrond & libjson-c dependency
gluon-hoodselector-add-VPN-MODE: check running hoodselector before loading lua
gluon-hoodselector-add-VPN-MODE: remove nixio dependency from hoodselector util
Revert "gluon-hoodselector-add-VPN-MODE: check running hoodselector before loading lua"
This reverts commit 535b0a1b2fb73e563bf6a44b568a796440bd307f.
add luaposix and luabitop to pakage dependency
sbin/hoodselector: remove nixio requiemend
sbin/hoodselector: load hoods only if necessary
gluon-hoodselector: use VPN abstraction layer. the hoodselectore does
not need to know about all individual VPN protocols.
gluon-hoodselector: Makefile add gluon-mesh-vpn-core as dependency
gluon-hoodselector: apply changes of mesh vpn lib
gluon-hoodselector: remove outdated comments
package/gluon-hoodselector: check_site.lua rm domain seed check thus its already checked by gluon-core
package/gluon-hoodselector: util.lua code cleanup and refactoring
package/gluon-hoodselector: hoodselector code cleanup and refactoring
gluon-hoodselector: util.lua, use taps instead of spaces. Use posix.unistd.access instead of io.open
Signed-off-by: Jan-Tarek Butt <tarek@ring0.de>
gluon-hoodselector: hoodselector, use taps instead of spaces.
Signed-off-by: Jan-Tarek Butt <tarek@ring0.de>
gluon-hoodselector: check_site.lua: replace hood with domain
Signed-off-by: Jan-Tarek Butt <tarek@ring0.de>
gluon-hoodselector: drop VPN mode and rename hood to domain. Furthermore implement geolocator mode as neorayder way
Signed-off-by: Jan-Tarek Butt <tarek@ring0.de>
package/gluon-hoodselector: rm duplicated print output
Signed-off-by: Jan-Tarek Butt <tarek@ring0.de>
package/gluon-hoodselector util: fix wrong function signature
Signed-off-by: Jan-Tarek Butt <tarek@ring0.de>
small typo fixes
small typo fixes
Update util.lua
processes are really restarted now. new (old) problem: nodes will not forget their former ipv6-addresses. watchdog could here with that.
gluon-hoodselector util.lua: replace i iterator with _
Signed-off-by: Jan-Tarek Butt <tarek@ring0.de>
Update util.lua
now polygons with holes are recognized correctly. also a mix of nested polygons and boxes should be possible as shapes[]
package/gluon-hoodselector: hoodselector use gluon-reload for daemon restarts/reloads
Signed-off-by: Jan-Tarek Butt <tarek@ring0.de>
package/gluon-hoodselector: util.lua use math-polygon lib and rm restart_services function. Rectengles will be converted into polygons now
Signed-off-by: Jan-Tarek Butt <tarek@ring0.de>
package/gluon-hoodselector: Makefile rewrite description update depends list
Signed-off-by: Jan-Tarek Butt <tarek@ring0.de>
package/gluon-hoodselector: check_site.lua reduce complexity
Signed-off-by: Jan-Tarek Butt <tarek@ring0.de>
package/gluon-hoodselector: use : for gluon_version Val
Signed-off-by: Jan-Tarek Butt <tarek@ring0.de>
package/gluon-hoodselector: fix if equal syntax
Signed-off-by: Jan-Tarek Butt <tarek@ring0.de>
luasrc/usr/lib/lua/hoodselector/util.lua: check_site.lua simplify checksite script and fix if logic
Signed-off-by: Jan-Tarek Butt <tarek@ring0.de>
package/gluon-hoodselector: set space after comma, rm unnecessary error handling
Signed-off-by: Jan-Tarek Butt <tarek@ring0.de>
package/gluon-hoodselector: use only brackes on require function no mixup
Signed-off-by: Jan-Tarek Butt <tarek@ring0.de>
package/gluon-hoodselector: check_site.lua rm unuse variables and fix non std global function
Signed-off-by: Jan-Tarek Butt <tarek@ring0.de>
package/gluon-hoodselector: util.lua rm unuse include
Signed-off-by: Jan-Tarek Butt <tarek@ring0.de>
package/gluon-hoodselector: rm comment return nil in function get_geolocation()
Signed-off-by: Jan-Tarek Butt <tarek@ring0.de>
package/gluon-hoodselector: Makefile refactor pkg description
Signed-off-by: Jan-Tarek Butt <tarek@ring0.de>
We now keep the VPN enable state, bandwidth limit enable and actual limits
in the core config to avoid having to recover "user intent" from different
config files when the used VPN packages change.
Fixes#1736
Several fixes and enhancements related to multicast were added upstream
in batman-adv. So let's give the batman-adv multicast optimizations
another go.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
The is_outdoor function is placed inside the gluon.platform module, not
the platform_info module. Currently, the outdoor-mode wizard component
and the upgrade script fail due to nil-value calls.
adds a section to the wizard for outdoor capable devices
that informs the user of of the regulatory situation and
allows a quick toggle of the outdoor mode.
Add the `wifi5.outdoor_chanlist` site configuration that
allows specifying an outdoor channel range that can be
switched to for regulatory compliance.
Upon enabling the outdoor option the device will
- configure the `outdoor_chanlist` on all 5 GHz radios
- which may enable DFS/TPC, based on the regulatory domain
- disable ibss/mesh on the 5 GHz radio, as DFS *will*
break mesh connections
- allow for htmode reconfiguration on 5 GHz radios
The outdoor option can be toggled from
- Advanced Settings
- W-LAN
- Outdoor Installation
The `preserve_channel` flag overrules the outdoor channel
selection.
The batctl v2013.4 build was removed from the batman-adv-legacy package
as the current, upstream batctl releases work with batman-adv-legacy,
too.
As a replacement we need to add the upstream batctl dependency to
gluon-mesh-batman-adv-14 to have a batctl available again here.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
The commit a080049735 ("gluon-status-page-mesh-batman-adv: Retrieve TQ of
neighbors with non-best direct link") removed the check whether a neighbor
has the BATADV_ATTR_FLAG_BEST set. But consumers may still want to filter
out or mark neighbors which don't have this flag set. To assist with such a
feature, enhance the neighbor object with an extra boolean "best" attribute
which stores whether the BATADV_ATTR_FLAG_BEST was found or not.
Reported-by: Vincent Wiemann <webmaster@codefetch.de>
The commit ee63ed42fe ("gluon-mesh-batman-adv: List neighbors with
non-best direct link") removed the check whether a neighbor has the
BATADV_ATTR_FLAG_BEST set. But consumers may still want to filter out or
mark neighbors which don't have this flag set. To assist with such a
feature, enhance the neighbor object with an extra boolean "best" attribute
which stores whether the BATADV_ATTR_FLAG_BEST was found or not.
Reported-by: Vincent Wiemann <webmaster@codefetch.de>
Links between two direct neighbors are not always the best route between
these devices. The flag BATADV_ATTR_FLAG_BEST would not be set for these
originator entries and the respondd module would just ignore this entry.
If these neighbors are not accepted and returned to the status page then
some of the neighbor entries will show a name, (acceptable) signal strength
and mac address but no TQ value.
Fixes: 28668c8c52 ("gluon-status-page: API")
Links between two direct neighbors are not always the best route between
these devices. The flag BATADV_ATTR_FLAG_BEST would not be set for these
originator entries and the respondd module would just ignore this entry.
This causes missing links in meshviewer and similar tools. And when the
link quality is nearly equal and but fluctuates slightly, these links will
from time to time appear and disappear on the map.
Fixes: 2e0e24a992 ("announce neighbours using alfred/gluon-announce")
The device is broken until the next release. The LEDs are currently not
working (fixed in current OpenWRT master).
Also give a brief explanation about the BROKEN status being dependent on
the WiFi chip used and not the SoC family in general.
When two domains alias the same name (or one aliases another), display a
meaningful error message like:
Failed to alias domain 'foo' as 'bar', name already taken by
domain 'baz'.
The amount of local wifi clients is currently counted by two different
ways:
* asking the kernel wifi layer for the number of of clients on 2.4GHz and
5GHz band
* asking batman-adv for the number of non-timed out entries in the local
translation table with WiFi flag
The number of wifi24+wifi5 and the number of TT wifi client counts are
reported via respondd to various consumers. The ffrgb meshviewer is
displaying these values as:
* 2,4 GHz: wifi24
* 5 GHz: wifi5
* other: (TT local wifi+non-wifi clients) - (wifi24 + wifi5)
But the local translation table is holding entries much longer than the
wifi layer. It can therefore easily happen that a wifi client disappears in
the kernel wifi layer and batman-adv still has the entry stored in the
local TT.
The ffrgb meshviewer would then show this count in the category "other".
This often results in confusions because "other" is usually for ethernet
clients. And nodes with a frequently disappearing larger group of clients
(near bus stations or larger intersections) often show most clients under
the group "other" even when this devices doesn't have a LAN ethernet port.
It is better for presentation to calculate the number of total wifi clients
by summing up wifi24 + wifi5. And getting the number of total clients (non
wifi + wifi) by adding the result of the previous calculation to the sum of
non-wifi client in the local batman-adv translation table.
Fixes: 89a9d8138c ("gluon-mesh-batman-adv-core: Announce client count by frequency")
Reported-by: Pascal Wettin <p.wettin@gmx.de>
Gluon has multiple ways to obtain unique MAC-addresses. They are either
provided by the WiFi driver or derived from the primary MAC-address.
Quoting the same file:
> It's necessary that the first 45 bits of the MAC address don't
> vary on a single hardware interface, since some chips are using
> a hardware MAC filter. (e.g 'rt305x')
This currently fails in case the rt35xx based chips mac address differs
from the primary MAC. In this case, the MAC address for the client0 radio
(vif 1) comes from the WiFi driver. As there is only a single
MAC-address provided by '/sys/class/ieee80211/phyX/addresses' but the
MAC-address for mesh 0 (vif 2) is derived from the Node-ID, resulting in
different first 45 bits. The WiFi won't come up altogether in this case.
This commit verifies at least 4 MAC-Addresses are provided by the WiFi
driver. If this is not the case, all MAC-addresses are derived from the
primary MAC. This way, affected radios are working correctly.
This commit distributes dualband radios evenly on 2.4 GHz and 5GHz with
2.4 GHz being prioritised higher than 5 GHz. This means in case a device
has only a single radio and this radio supports operation in both bands,
it will be set to 2.4 GHz.
Tested-by: Martin Weinelt <martin@darmstadt.freifunk.net>
Signed-off-by: David Bauer <mail@david-bauer.net>
Allow odhcp6c to fork the script to handle router
advertisments in 30 seconds intervals. This is the value
that was previously used in Gluon v2018.1 / LEDE 17.01.
The default value is 3 seconds and while it is RFC compliant
it can put alot of pressure on even moderately sized devices.
Signed-off-by: Martin Weinelt <martin@darmstadt.freifunk.net>
log-file /dev/stderr is broken for babeld as it eats log messages for debug log.
This commit gets rid of the option. This allows -d N to be used as babeld command
line option.
This patch makes use of the new feature in l3roamd to gracefully
add, remove and list the mesh interfaces that are currently in use. This
helps when changing mesh interfaces often - a characteristic of the
wireguard protocol implementation as in the previous behavior all local
clients are dropped when adjusting mesh interfaces.
gluon-wan is a sudo-like exec wrapper that switches the process group to
gluon-mesh-vpn, making it use the WAN dnsmasq rather than resolving over
the mesh.
Note that this only affects DNS at the moment. Processes running under
gluon-wan will still use the regular mesh IPv6 routing table, and not the
WAN routing table. This is not a problem for IPv4, as there is only one
IPv4 routing table.
Fixes#1575
Rename to respondd.c / respondd.so, gluon.mk expects these names. This way
we can remove the install code. The installed filename is changed to
gluon-mesh-babel.so, bringing it in line with out common naming scheme.
The redirect and dnat target are needed for gluon-alt-esc-client to
forward frames to the selected, alternative gateways.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
This adds support for the TP-Link TL-WR902Ac v1 travel router.
The device is marked as broken due to 64MB which might be insufficient
in certain environments.
Before 7827f89, mandatory hostname field in config mode was
pre-filled with the default hostname.
This commit adds the config_mode.hostname.prefill option for
controlling the default value.
this activates the package by default when using the batman feature
while still allowing to explicitly remove it like this:
GLUON_SITE_PACKAGES := \
-gluon-ebtables-limit-arp
gluon-config-mode-geo-location-osm extends the
gluon-config-mode-geo-location with a location picker based on
OpenStreetMaps.
Based-on-patch-by: Jan-Tarek Butt <tarek@ring0.de>
