net.ipv6.conf.br-client.forwarding is moved from gluon-client-bridge to
gluon-mesh-batman-adv, as the setting is not useful with non-bridged
protocols.
With the batman-adv multicast support compiled back in again we end up
with multicast addresses in the batman-adv translation table.
Currently we wrongly interpret multicast addresses returned by TT as a
unique host, too, which adds them with a source address filter to
ebtables as well. However, the source address of an ethernet frames is
never supposed to be a multicat one.
This leads to unnecessary entries in ebtables. Fixing this by ignoring
those MAC addreses returned by TT which have the multicast bit set.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
This setting allows to enforce manually setting a hostname.
In the initial configuration, the hostname field is now left empty; when
setting the hostname is not enforced, the default hostname is shown as the
field placeholder.
Fixes#1139
Our VXLAN setup was changed to accept VXLAN packets without checksum almost
2 months ago, so we can disable sending the checksums now as well. Slightly
improves performance.
The RFC standard multicast querier interval is 120s. Our querier uses in
interval of 20s for better support of roaming clients, but our robustness
setting of 3 leads to external queriers using the standard interval to be
timeout after only 60s, leading to frequent "querier appeared/disappeared"
messages. Increase robustness so that external queriers with any interval
<180s are supported.
We must ensure that each node becomes IGMP/MLD querier for its local
clients; having only a single querier for the whole mesh is generally
unreliable, leading to frequent "IGMP/MLD querier appeared/disappeared"
messages from batman-adv and unreliable snooping.
In smaller meshes it might be interesting only segment querier domains, but
allow membership reports to pass through the mesh, in order to support
snooping switches outside the mesh without special configuration. A
site.conf switch is provided to control this behaviour.
Fixes#1320
A downside of this behaviour is that the page does not work for IPv4-only
clients, as the redirect will always point at an IPv6 address.
Still, it seems like a good idea to enforce the redirect even from the IPv4
next-node address, as switching nodes while being connected to the status
page would lead to unexpected behaviour.
All Access-Control-Allow-Origin are removed to improve users' privacy. As
the status page API is thus not useful without the status page anymore,
merge them back into a single package.
The status-page-api respondd provider is removed as well.
Fixes#1194
This new status page is significantly smaller than the old one. It always
loads its resources from the same host as the page itself, not requiring
cross-origin requests anymore.
It also uses the common i18n infrastructure of gluon-web.
Fixes#914
- CGI script and index.html are moved from gluon-web to
gluon-config-mode-core, the script is renamed to 'config'
- gluon-web and gluon-web-model base views and i18n files are symlinked
into the new path
- gluon-web-theme is renamed to gluon-config-mode-theme and installs
directly into the new path
- all gluon-web-* models, controllers and views are moved into the new
path
By emitting Lua code to call translate() and pcdata(), we are more
flexible than when doing this internally in the parser. The performance
penalty should be negligible.
This patch moves the prefix4 subnet route from the local-node veth
device to br-client (while keeping the next node ipv4 address on the
local node device).
This is in preparation to allow routing over the br-client interface
later.
This package adds filters to limit the amount of ARP Requests
devices are allowed to send into the mesh. The limits are 6 packets
per minute per client device, by MAC address, and 1 per second per
node in total.
A burst of up to 50 ARP Requests is allowed until the rate-limiting
takes effect (see --limit-burst in the ebtables manpage).
Furthermore, ARP Requests with a target IP already present in the
batman-adv DAT Cache are excluded from the rate-limiting,
both regarding counting and filtering, as batman-adv will respond
locally with no burden for the mesh. Therefore, this limiter
should not affect popular target IPs, like gateways.
However it should mitigate the problem of curious people or
smart devices scanning the whole IP range. Which could create
a significant amount of overhead for all participants so far.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Both gluon.sysconfig and libgluonutil already remove the trailing newline
if it exists. It's nicer to avoid files without a trailing newline, e.g.
for printing the file contents in a terminal.
This is currently only implemented in the gluon-mesh-vpn-fastd
package.
Advertising the public key may be deemed problematic when
your threat-model involves protecting the nodes privacy
from tunnel traffic correlation by onlink observers.
It can be enabled by setting site.mesh_vpn.fastd.pubkey_privacy
to `false`.
If a value is unset or optional, an empty choice is added to the selection.
This empty choice will be marked as invalid if the value is not optional.
This is properly supported for the 'select' widget only for now, and not
for 'radio'.
This package drops all incoming router advertisements except for the
default router with the best metric according to B.A.T.M.A.N. advanced.
Note that advertisements originating from the node itself (for example
via gluon-radvd) are not affected.
Also disabling TX checksums and not only allowing incoming packets without
checksum will provide another small speedup. As doing so would break wired
meshing with VXLAN-enabled nodes that require non-zero checksums, we will
wait a few days before this step.
In addition to significant internal differences in check_site_lib.lua (in
particular unifying error handling to a single place for the upcoming
multi-domain support), this changes the way fields are addressed in site
check scripts: rather than providing a string like 'next_node.ip6', the
path is passed as an array {'next_node', 'ip6'}.
Other changes in site check scripts:
* need_array and need_table now pass the full path to the sub fields to the
subcheck instead of the key and value
* Any check referring to a field inside a table implies that all higher
levels must be tables if they exist: a check for {'next_node', 'ip6'} adds
an implicit (optional) check for {'next_node'}, which allows to remove many
explicit checks for such tables
This should not convert JSON to a Lua table and back, as this loses the
distinction between arrays and objects, but as our site.conf is defined in
Lua anyways (for now), this can be fixed in a later revision.
[Matthias Schiffer: rename to gluon-show-site, rebase]
By basing the Lua gluon.site module on gluonutil_load_site_config(), the
config load implementation needs to changed only in a single place for
multi-domain support.
This enables the ebtables internal locking mechanism which
will avoid race conditions between multiple, concurrent
ebtables calls.
This is a preparation for the upcoming gluon-arp-limiter
daemon, to avoid issues if upon restarting gluon-ebtables
the gluon-arp-limiter daemon tries to modify the tables.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Interacting with batman-adv's genl interface requires some code and
definitions which could be shared between different packages. libbatadv is
trying to do this without providing any guarantee for ABI or API stability.
It is only useful in very controlled environments like gluon.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
* gluon-core, gluon-client-bridge: introduce new firewall zone: local_client
* gluon-core: put clients in local_client zone, introduce drop-zone,
set dns-rules and zones
* gluon-respondd: allow respondd on mesh
* gluon-status-page-api: allow http input on mesh and client
Filtering by MAC address won't filter out multicast packages like router
solicitations, causing uradvd to send out router advertisements with
maximum frequency (every 3 seconds) in active meshes, even when no local
client is actually interested in the advertisements.
Fixes#1230
The new gluon.site lua library will eventually replace gluon.site_config
(which is hereby deprecated, but will continue to be supported for a
while).
The new gluon.site library will wrap all values to allow traversing
non-existing tables without errors.
site = require 'gluon.site'
c = site.a.b.c -- doesn't fail even if a or a.b don't exist
The wrapped values must be unwrapped using call syntax:
site_name = site.site_name()
Using the call syntax on a non-existing value will return nil. An
alternative default value may be passed instead:
mac = site.next_node.mac('16:41:95:40:f7:dc')
The generic upgrade script is moved to run after the more specific scripts.
In addition, the script will now remove the configuration sections of
uninstalled VPN packages, so both positive and negative changes of the
default enable state can be migrated correctly.
Based-on-patch-by: Cyrus Fox <cyrus@lambdacore.de>
Fixes: #1187
When a Gluon node is used to connect to an uplink router/DHCP server (for
example in deployments without VPN tunnels), the gw_mode must be set to
server; this should be preserved on upgrades.
Fixes#1196
To reduce the number of packages that need to be listed in
GLUON_SITE_PACKAGES, this adds a new variable GLUON_FEATURES. Sets of
packages are enabled automatically based on the combination of listed
feature flags.
Site-specified package feeds can provide their own feature flag
definitions.
As PROVIDES can be used to replace real packages now, we don't need the
virtual packages as workaround anymore. This also means that the providing
packages don't need to be added to site.mk explicitly anymore when the
default provider is used.
